| Age | Commit message (Collapse) | Author |
|---|
|
hpet_disable is called unconditionally on machine reboot if hpet support
is compiled in the kernel.
hpet_disable only checks if the machine is hpet capable but doesn't make
sure that hpet has been initialized.
[ tglx: Made it a one liner and removed the redundant hpet_address check ]
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <alpine.DEB.2.00.1007211726240.22235@kaball-desktop>
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
After programming the HPET, we do a readback as a workaround for
ATI/SBx00 chipsets as a synchronization. Unfortunately this triggers
an erratum in newer ICH chipsets (ICH9+) where reading the comparator
immediately after the write returns the old value. Furthermore, as
always, I/O reads are bad for performance.
Therefore, restrict the readback to the chipsets that need it, or, for
debugging purposes, when we are running with hpet=verbose.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <20100225185348.GA9674@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: Fix double enable_IR_x2apic() call on SMP kernel on !SMP boards
x86: Increase CONFIG_NODES_SHIFT max to 10
ibft, x86: Change reserve_ibft_region() to find_ibft_region()
x86, hpet: Fix bug in RTC emulation
x86, hpet: Erratum workaround for read after write of HPET comparator
bootmem, x86: Fix 32bit numa system without RAM on node 0
nobootmem, x86: Fix 32bit numa system without RAM on node 0
x86: Handle overlapping mptables
x86: Make e820_remove_range to handle all covered case
x86-32, resume: do a global tlb flush in S4 resume
|
|
We think there exists a bug in the HPET code that emulates the RTC.
In the normal case, when the RTC frequency is set, the rtc driver tells
the hpet code about it here:
int hpet_set_periodic_freq(unsigned long freq)
{
uint64_t clc;
if (!is_hpet_enabled())
return 0;
if (freq <= DEFAULT_RTC_INT_FREQ)
hpet_pie_limit = DEFAULT_RTC_INT_FREQ / freq;
else {
clc = (uint64_t) hpet_clockevent.mult * NSEC_PER_SEC;
do_div(clc, freq);
clc >>= hpet_clockevent.shift;
hpet_pie_delta = (unsigned long) clc;
}
return 1;
}
If freq is set to 64Hz (DEFAULT_RTC_INT_FREQ) or lower, then
hpet_pie_limit (a static) is set to non-zero. Then, on every one-shot
HPET interrupt, hpet_rtc_timer_reinit is called to compute the next
timeout. Well, that function has this logic:
if (!(hpet_rtc_flags & RTC_PIE) || hpet_pie_limit)
delta = hpet_default_delta;
else
delta = hpet_pie_delta;
Since hpet_pie_limit is not 0, hpet_default_delta is used. That
corresponds to 64Hz.
Now, if you set a different rtc frequency, you'll take the else path
through hpet_set_periodic_freq, but unfortunately no one resets
hpet_pie_limit back to 0.
Boom....now you are stuck with 64Hz RTC interrupts forever.
The patch below just resets the hpet_pie_limit value when requested freq
is greater than DEFAULT_RTC_INT_FREQ, which we think fixes this problem.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <201003112200.o2BM0Hre012875@imap1.linux-foundation.org>
Signed-off-by: Daniel Hecht <dhecht@vmware.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
On Wed, Feb 24, 2010 at 03:37:04PM -0800, Justin Piszcz wrote:
> Hello,
>
> Again, on the Intel DP55KG board:
>
> # uname -a
> Linux host 2.6.33 #1 SMP Wed Feb 24 18:31:00 EST 2010 x86_64 GNU/Linux
>
> [ 1.237600] ------------[ cut here ]------------
> [ 1.237890] WARNING: at arch/x86/kernel/hpet.c:404 hpet_next_event+0x70/0x80()
> [ 1.238221] Hardware name:
> [ 1.238504] hpet: compare register read back failed.
> [ 1.238793] Modules linked in:
> [ 1.239315] Pid: 0, comm: swapper Not tainted 2.6.33 #1
> [ 1.239605] Call Trace:
> [ 1.239886] <IRQ> [<ffffffff81056c13>] ? warn_slowpath_common+0x73/0xb0
> [ 1.240409] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.240699] [<ffffffff81056cb0>] ? warn_slowpath_fmt+0x40/0x50
> [ 1.240992] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241281] [<ffffffff81041ad0>] ? hpet_next_event+0x70/0x80
> [ 1.241573] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241859] [<ffffffff81078e32>] ? tick_handle_oneshot_broadcast+0xe2/0x100
> [ 1.246533] [<ffffffff8102a67a>] ? timer_interrupt+0x1a/0x30
> [ 1.246826] [<ffffffff81085499>] ? handle_IRQ_event+0x39/0xd0
> [ 1.247118] [<ffffffff81087368>] ? handle_edge_irq+0xb8/0x160
> [ 1.247407] [<ffffffff81029f55>] ? handle_irq+0x15/0x20
> [ 1.247689] [<ffffffff810294a2>] ? do_IRQ+0x62/0xe0
> [ 1.247976] [<ffffffff8146be53>] ? ret_from_intr+0x0/0xa
> [ 1.248262] <EOI> [<ffffffff8102f277>] ? mwait_idle+0x57/0x80
> [ 1.248796] [<ffffffff8102645c>] ? cpu_idle+0x5c/0xb0
> [ 1.249080] ---[ end trace db7f668fb6fef4e1 ]---
>
> Is this something Intel has to fix or is it a bug in the kernel?
This is a chipset erratum.
Thomas: You mentioned we can retain this check only for known-buggy and
hpet debug kind of options. But here is the simple workaround patch for
this particular erratum.
Some chipsets have a erratum due to which read immediately following a
write of HPET comparator returns old comparator value instead of most
recently written value.
Erratum 15 in
"Intel I/O Controller Hub 9 (ICH9) Family Specification Update"
(http://www.intel.com/assets/pdf/specupdate/316973.pdf)
Workaround for the errata is to read the comparator twice if the first
one fails.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20100225185348.GA9674@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com>
Cc: <stable@kernel.org>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Pass the clocksource as an argument to the clocksource resume callback.
Needed so we can point out which CMT channel the sh_cmt.c driver shall
resume.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
HPET MSI on platforms with ATI SB700/SB800 as they seem to have some
side-effects on floppy DMA. Do not use HPET MSI on such platforms.
Original problem report from Mark Hounschell
http://lkml.indiana.edu/hypermail/linux/kernel/0912.2/01118.html
[ This patch needs to go to stable as well. But, there are some
conflicts that prevents the patch from going as is. I can
rebase/resubmit to stable once the patch goes upstream.
hpa: still Cc:'ing stable@ as an FYI. ]
Tested-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100121190952.GA32523@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Andrew complained rightly that the WARN_ON in hpet_next_event() is
confusing and the code comment not really helpful.
Change it to WARN_ONCE and print the reason in clear text. Change the
comment to explain what kind of hardware wreckage we deal with.
Pointed-out-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
|
|
x86 arch support for remapping HPET MSI's by associating the HPET timer block
with the interrupt-remapping HW unit and setting up appropriate irq_chip
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.630510000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
On 64-bits, using unsigned long when unsigned int suffices
needlessly creates larger code (due to the need for REX
prefixes), and most of the logic in hpet.c really doesn't need
64-bit operations.
At once this avoids the need for a couple of type casts.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <4A8BC9780200007800010832@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
If CPU support always running local APIC timer, per-cpu hpet
timer could be disabled, which is useless and wasteful in such
case. Let's leave the timers to others.
The effect is that we reserve less timers.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: venkatesh.pallipadi@intel.com
LKML-Reference: <20090812031612.GA10062@sli10-desk.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The hpet per cpu timers request their interrupt without setting the
IRQF_TIMER flag so suspend_device_irqs() disables them as well which
results in a fatal resume failure on the boot CPU.
Adding IRQF_TIMER to the interupt flags when requesting the hpet per
cpu timer interrupts solves the problem.
Reported-by: Benjamin S. <sbenni@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Benjamin S. <sbenni@gmx.de>
Cc: stable@kernel.org
|
|
(See http://bugzilla.kernel.org/show_bug.cgi?id=12961)
It partially reverts commit c23e253e67c9d8a91a0ffa33c1f571a17f0a2403
(x86: hpet: stop HPET_COUNTER when programming periodic mode)
HPET on AMD 81xx chipset needs a second write (with HPET_TN_SETVAL
cleared) to T0_CMP register to set the period in periodic mode.
With this patch HPET_COUNTER is still stopped but not reset when HPET
is programmed in periodic mode. This should help to avoid races when
HPET is programmed in periodic mode and fixes a boot time hang that
I've observed on a machine when using 1000HZ.
[ Impact: fix boot time hang on machines with AMD 81xx chipset ]
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Jeff Mahoney <jeffm@suse.com>
LKML-Reference: <20090421180037.GA2763@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: fix system hang on some systems operating with HZ_1000
On a system that stalled with HZ_1000, the first value written to
T0_CMP (when the main counter was not stopped) did not trigger an
interrupt. Instead after the main counter wrapped around (after
several minutes) an interrupt was triggered and afterwards the
periodic interrupt took effect.
This can be fixed by implementing HPET spec recommendation for
programming the periodic mode (i.e. stopping the main counter).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Hounschell <markh@compro.net>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
By splitting up existing hpet_start_counter function.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Hounschell <markh@compro.net>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Mark Hounschell <markh@compro.net>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: fix preemption bug
x86, olpc: fix model detection without OFW
x86, hpet: fix for LS21 + HPET = boot hang
x86: CPA avoid repeated lazy mmu flush
x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
x86/cpa: make sure cpa is safe to call in lazy mmu mode
x86, ptrace, mm: fix double-free on race
|
|
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce33590687888ebb900d09557b8807c4539022, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Implement Linus's suggestion: introduce the hpet_cnt_ahead()
helper function to compare hpet time values - like other
wrapping counter comparisons are abstracted away elsewhere.
(jiffies, ktime_t, etc.)
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There's a small problem with hpet_rtc_reinit function - it checks
for the:
hpet_readl(HPET_COUNTER) - hpet_t1_cmp > 0
to continue increasing both the HPET_T1_CMP (register) and the
hpet_t1_cmp (variable).
But since the HPET_COUNTER is always 32-bit, if the hpet_t1_cmp
is 64-bit this condition will always be FALSE once the latter hits
the 32-bit boundary, and we can have a situation, when we don't
increase the HPET_T1_CMP register high enough.
The result - timer stops ticking, since HPET_T1_CMP becomes less,
than the COUNTER and never increased again.
The solution is (based on Linus's suggestion) to not compare 64-bits
(on 64-bit x86), but to do the comparison on 32-bit signed
integers.
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: Fix debugobjects warning
debugobject enabled kernels spit out a warning in hpet code due to a
workqueue which is initialized on stack.
Add INIT_WORK_ON_STACK() which calls init_timer_on_stack() and use it
in hpet.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix warning in kernel/hrtimer.c
x86: make sure we really have an hpet mapping before using it
x86: enable HPET on Fujitsu u9200
linux/timex.h: cleanup for userspace
posix-timers: simplify de_thread()->exit_itimers() path
posix-timers: check ->it_signal instead of ->it_pid to validate the timer
posix-timers: use "struct pid*" instead of "struct task_struct*"
nohz: suppress needless timer reprogramming
clocksource, acpi_pm.c: put acpi_pm_read_slow() under CONFIG_PCI
nohz: no softirq pending warnings for offline cpus
hrtimer: removing all ur callback modes, fix
hrtimer: removing all ur callback modes, fix hotplug
hrtimer: removing all ur callback modes
x86: correct link to HPET timer specification
rtc-cmos: export second NVRAM bank
Fixed up conflicts in sound/drivers/pcsp/pcsp.c and sound/core/hrtimer.c
manually.
|
|
Impact: prepare the hpet code for Xen dom0 booting
When booting in Xen dom0, the hpet isn't really accessible, so make
sure the mapping is non-NULL before use.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: auto-enable HPET on Fujitsu u9200
HPET timer is listed in the ACPI table, but needs a quirk entry in order to
work. Unfortunately, the quirk code runs after first HPET hpet_enable() which
has already determined that the timer doesn't work (reads 0xFFFFFFFF). This
patch allows hpet_enable() to be called again after running the quirk code.
Signed-off-by: Janne Kulmala <janne.t.kulmala@tut.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
|
|
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
|
|
Impact: fix build warning
this warning:
arch/x86/kernel/hpet.c:36: warning: ‘hpet_num_timers’ defined but not used
Triggers because hpet_num_timers is unused in the !CONFIG_PCI_MSI case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: make global variable static
Fix this sparse warning:
arch/x86/kernel/hpet.c:36:18: warning: symbol 'hpet_num_timers' was
not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Some functions that may be called from this handler require that
interrupts are disabled. Also, combining IRQF_DISABLED and
IRQF_SHARED does not reliably disable interrupts in a handler, so
remove IRQF_SHARED from the irq flags (this irq is not shared anyway).
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Cc: "Will Newton" <will.newton@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In hpet_next_event() we check that the value we just wrote to
HPET_Tn_CMP(timer) has reached the chip. Currently, we're checking that
the value we wrote to HPET_Tn_CMP(timer) is in HPET_T0_CMP, which, if
timer is anything other than timer 0, is likely to fail.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
It is possible to flood the console with call traces if the WARN_ON
condition is true because of the frequency with which this function is
called.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix the below compile warnings due to recent HPET MSI changes
arch/x86/kernel/hpet.c:48: warning: 'hpet_devs' defined but not used
arch/x86/kernel/hpet.c:50: warning: 'per_cpu__cpu_hpet_dev' defined but not used
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
v2: fix hpet compiling error
v3: Bjorn want to use dev_printk instead
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Added dummy function for hpet_setup_msi_irq().
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
On Sat, Sep 06, 2008 at 06:03:53AM -0700, Ingo Molnar wrote:
>
> it crashes two testsystems, the fault on a NULL pointer in hpet init,
> with:
>
> initcall print_all_ICs+0x0/0x520 returned 0 after 26 msecs
> calling hpet_late_init+0x0/0x1c0
> BUG: unable to handle kernel NULL pointer dereference at 000000000000008c
> IP: [<ffffffff80d228be>] hpet_late_init+0xfe/0x1c0
> PGD 0
> Oops: 0000 [1] SMP
> CPU 0
> Modules linked in:
> Pid: 1, comm: swapper Not tainted 2.6.27-rc5 #29725
> RIP: 0010:[<ffffffff80d228be>] [<ffffffff80d228be>] hpet_late_init+0xfe/0x1c0
> RSP: 0018:ffff88003fa07dd0 EFLAGS: 00010246
> RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
> RDX: ffffc20000000160 RSI: 0000000000000000 RDI: 0000000000000003
> RBP: ffff88003fa07e90 R08: 0000000000000000 R09: ffff88003fa07dd0
> R10: 0000000000000001 R11: 0000000000000000 R12: ffff88003fa07dd0
> R13: 0000000000000002 R14: ffffc20000000000 R15: 000000006f57e511
> FS: 0000000000000000(0000) GS:ffffffff80cf6a80(0000) knlGS:0000000000000000
> CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
> CR2: 000000000000008c CR3: 0000000000201000 CR4: 00000000000006e0
> DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
> Process swapper (pid: 1, threadinfo ffff88003fa06000, task ffff88003fa08000)
> Stack: 00000000fed00000 ffffc20000000000 0000000100000003 0000000800000002
> 0000000000000000 0000000000000000 0000000000000000 0000000000000000
> 0000000000000000 0000000000000000 0000000000000000 0000000000000000
> Call Trace:
> [<ffffffff80d227c0>] ? hpet_late_init+0x0/0x1c0
> [<ffffffff80209045>] do_one_initcall+0x45/0x190
> [<ffffffff80296f39>] ? register_irq_proc+0x19/0xe0
> [<ffffffff80d0d140>] ? early_idt_handler+0x0/0x73
> [<ffffffff80d0dabc>] kernel_init+0x14c/0x1b0
> [<ffffffff80942ac1>] ? trace_hardirqs_on_thunk+0x3a/0x3f
> [<ffffffff8020dbd9>] child_rip+0xa/0x11
> [<ffffffff8020ceee>] ? restore_args+0x0/0x30
> [<ffffffff80d0d970>] ? kernel_init+0x0/0x1b0
> [<ffffffff8020dbcf>] ? child_rip+0x0/0x11
> Code: 20 48 83 c1 01 48 39 f1 75 e3 44 89 e8 4c 8b 05 29 29 22 00 31 f6 48 8d 78 01 66 66 90 89 f0 48 8d 04 80 48 c1 e0 05 4a 8d 0c 00 <f6> 81 8c 00 00 00 08 74 26 8b 81 80 00 00 00 8b 91 88 00 00 00
> RIP [<ffffffff80d228be>] hpet_late_init+0xfe/0x1c0
> RSP <ffff88003fa07dd0>
> CR2: 000000000000008c
> Kernel panic - not syncing: Fatal exception
There was one code path, with CONFIG_PCI_MSI disabled, where we were accessing
hpet_devs without initialization. That resulted in the above crash. The change
below adds a check for hpet_devs.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Initialize a per CPU HPET MSI timer when possible. We retain the HPET
timer 0 (IRQ 0) and timer 1 (IRQ 8) as is when legacy mode is being used. We
setup the remaining HPET timers as per CPU MSI based timers. This per CPU
timer will eliminate the need for timer broadcasting with IRQ 0 when there
is non-functional LAPIC timer across CPU deep C-states.
If there are more CPUs than number of available timers, CPUs that do not
find any timer to use will continue using LAPIC and IRQ 0 broadcast.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
small style cleanups.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Basic HPET MSI setup code. Routines to perform basic MSI read write
in HPET memory map and setting up irq_chip for HPET MSI.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Preparatory patch before the actual HPET MSI changes. Sets up hpet_set_mode
and hpet_next_event for the MSI related changes. Just the code
refactoring and should be zero functional change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Minor /dev/hpet updates and bugfixes:
* Remove dead code, mostly remnants of an incomplete/unusable
kernel interface ... noted when addressing "sparse" warnings:
+ hpet_unregister() and a routine it calls
+ hpet_task and all references, including hpet_task_lock
+ hpet_data.hd_flags (and HPET_DATA_PLATFORM)
* Correct and improve boot message:
+ displays *counter* (shared between comparators) bit width,
not *timer* bit widths (which are often mixed)
+ relabel "timers" as "comparators"; this is less confusing,
they are not independent like normal timers are (sigh)
+ display MHz not Hz; it's never less than 10 MHz.
* Tighten and correct the userspace interface code
+ don't accidentally program comparators in 64-bit mode using
32-bit values ... always force comparators into 32-bit mode
+ provide the correct bit definition flagging comparators with
periodic capability ... the ABI is unchanged
* Update Documentation/hpet.txt
+ be more correct and current
+ expand description a bit
+ don't mention that now-gone kernel interface
Plus, add a FIXME comment for something that could cause big trouble
on systems with more capable HPETs than at least Intel seems to ship.
It seems that few folk use this userspace interface; it's not very
usable given the general lack of HPET IRQ routing. I'm told that
the only real point of it any more is to mmap for fast timestamps;
IMO that's handled better through the gettimeofday() vsyscall.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-cmos, in two ways:
- When HPET is stealing the IRQs, use the first IRQ to grab
the seconds counter which will be monitored (instead of
using whatever was previously in that memory);
- In sane IRQ handling modes, scrub out old IRQ status before
enabling IRQs.
That latter is done by tightening up IRQ handling for rtc-cmos everywhere,
also ensuring that when HPET is used it's the only thing triggering IRQ
reports to userspace; net object shrink.
Also fix a bogus HPET message related to its RTC emulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
keep the one for VSYSCALL_HPET
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
