summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)Author
2008-07-09[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.Patrice Vilchez
New timings are based on application note "NAND Flash Support on AT91SAM9 Microcontrollers" available at http://atmel.com/dyn/resources/prod_documents/doc6255.pdf). Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add support for L2 outer cache on XScale3Eric Miao
The initial patch from Lothar, and Lennert make it into a cleaner one, modified and tested on PXA320 by Eric Miao. This patch moves the L2 cache operations out of proc-xsc3.S into dedicated outer cache support code. CACHE_XSC3L2 can be deselected so no L2 cache specific code will be linked in, and that L2 enable bit will not be set, this applies to the following cases: a. _only_ PXA300/PXA310 support included and no L2 cache wanted b. PXA320 support included, but want L2 be disabled So the enabling of L2 depends on two things: - CACHE_XSC3L2 is selected - and L2 cache is present Where the latter is only a safeguard (previous testing shows it works OK even when this bit is turned on). IXP series of processors with XScale3 cannot disable L2 cache for the moment since they depend on the L2 cache for its coherent memory, so IXP may always select CACHE_XSC3L2. Other L2 relevant bits are always turned on (i.e. the original code enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side effects. Specifically, these bits are: - OC bits in TTBASE register (table walk outer cache attributes) - LLR Outer Cache Attributes (OC) in Auxiliary Control Register Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add simple gpio debug LEDs support for zyloniteEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add GPIO expander (PCA9539) support for zyloniteEric Miao
And also reserve 32 IRQs for the two GPIO expanders. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add pxa3xx NAND support for littletonEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add pxa3xx NAND support for zyloniteEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add pxa3xx NAND device and clock sourcesEric Miao
A pxa3xx_set_nand_info() is also introduced to set the PXA3xx NAND driver specific platform_data structure pointer. Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: move pxa310 specific MMC3 clk out of generic pxa3xx.cEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: make PXA3xx_CK() and PXA3xx_CKEN() public in clock.heric miao
So processor specific clock sources can be defined in pxa300.c and pxa320.c. Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state changeEric Miao
Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: introduce dedicated __mfp_validate() to check PXA2xx MFPEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: embed body of pxa320_init_mfp()Eric Miao
pxa320_init_mfp() is simple enough to be embedded into pxa320_init() to simplify the code a bit. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: remove WAKEUP_ON_LEVEL_HIGH from keypad direct keysEric Miao
Setting PKWR bits on those pins will make the resuming from low power state to fail. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: fix typo of CONFIG_*_MODULEEric Miao
The correct macro name when a driver is built as a module is CONFIG_*_MODULE instead of CONFIG_*_MODULES. This patch fixes this in several places. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: use IORESOURCE_IRQ_* instead of IRQF_* for IRQ resourceEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: add codename zylonite for PXA3xx Development PlatformEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09Merge branch 'machtypes' into pxa-palmRussell King
2008-07-09[ARM] 5103/2: CM-X270: update core platform supportMike Rapoport
Convert CM-X270 pin configuration to use MFP tables. Make device initialization dependent on respective driver CONFIG_ value (like in zylonite). Cleanup includes Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5101/2: EM-X270 updatesMike Rapoport
Convert EM-X270 pin configuration to use MFP tables and gpio library Make device initialization dependent on respective driver CONFIG_ value (like in zylonite) Add keypad and gpio_key devices Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5138/1: magician: set pwm-backlight .id = -1Philipp Zabel
There will always be only one pwm-backlight on this device. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5137/1: magician: MACH_MAGICIAN doesn't need to depend on ARCH_PXAPhilipp Zabel
It is only defined inside an "if ARCH_PXA ... endif" block, so the depends on is not needed. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>? Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5126/1: magician: remove superfluous mtd includesPhilipp Zabel
These were only needed for hardcoded flash partition tables, which were never submitted. It is better to have the bootloader pass the partition table to the kernel instead. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5125/1: magician: move gpio pin configuration into __initdata sectionPhilipp Zabel
The pin configuration array is only used during board init. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5119/1: magician: include linux/gpio.h instead of asm/gpio.hPhilipp Zabel
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5042/1: magician: request GPIOs for pda_powerPhilipp Zabel
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5095/2: pcm990: switch from pxa_gpio_mode to pxa2xx_mfp_configGuennadi Liakhovetski
pxa_gpio_mode() is deprecated, use the new pxa2xx_mfp_config() function to configure GPIOs in pcm990 platform code. Convert "array, ARRAY_SIZE(array)" to "ARRAY_AND_SIZE(array)" while at it. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5143/1: pxa: further cleanup PXA Kconfig by removing oneDmitry Baryshkov
unnecessary menu level Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5142/1: pxa: move move zaurus declarations to proper placeDmitry Baryshkov
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5088/3: pxa2xx: add pxa2xx_set_spi_info to register pxa2xx-spi ↵Guennadi Liakhovetski
platform devices Add a function to dynamically allocate and register pxa2xx-spi platform devices, to be used by PXA2xx and PXA3xx based systems. Switch pcm027 and lubbock to use it. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5084/1: zylonite: Register AC97 deviceMark Brown
The Zylonite has an AC97 subsystem on it so register the AC97 controller device. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration modelMark Brown
As well as moving all the device declarations to a single one in devices.c this causes all platforms to register the I/O and interrupt resources for the AC97 controller. Cc: eric miao <eric.miao@marvell.com> Cc: Mike Rapoport <mike@compulab.co.il> Cc: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Jürgen Schindele <linux@schindele.name> Cc: Juergen Beisert <jbe@pengutronix.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC ↵Philipp Zabel
drivers The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform driver name changes from pxa2xx-udc to pxa25x-udc) and the platform driver name of pxa27x_udc.c is fixed to pxa27x-udc. pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors and the pxa27x_device_udc is enabled in pxa27x.c. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Including from Ian Molton: Fixes for mistakes left over from the PXA2{5,7}X UDC split. Signed-off-by: Ian Molton <spyro@f2s.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] 5145/1: PXA2xx: provide api to control IrDA pins stateDmitry Baryshkov
Provide a set of functions to control state of pins dedicated to IrDA. Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09[ARM] pxa: remove pxa_set_cken()Russell King
pxa_set_cken() is now unused, remove it. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09Merge branches 'pxa-misc', 'pxa-pwm' and 'pxa-multi' into pxaRussell King
2008-07-09[ARM] pxa: allow clk aliasesRussell King
We need to support more than one name+device for a struct clk for a small number of peripherals. We do this by re-using struct clk alias to another struct clk - IOW, if we find that the entry we're using is an alias, we return the aliased entry not the one we found. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09powerpc: Fix problems with 32bit PPC's running with >= 4GB of RAMStefan Roese
This patch enables 32bit PPC's (with 36bit physical address space, e.g. IBM/AMCC PPC44x) to run with >= 4GB of RAM. Mostly its just replacing types (unsigned long -> phys_addr_t). Tested on an AMCC Katmai with 4GB of DDR2. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09powerpc/44x: Update ppc44x_defconfigJosh Boyer
Add the virtex and sam440ep platforms to the multiboard defconfig Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09powerpc/44x: Support NAND boot for Rev A Warp boardsSean MacLennan
Allow the Rev A Warp boards to boot from NAND. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09powerpc: rework 4xx PTE access and TLB missBenjamin Herrenschmidt
This is some preliminary work to improve TLB management on SW loaded TLB powerpc platforms. This introduce support for non-atomic PTE operations in pgtable-ppc32.h and removes write back to the PTE from the TLB miss handlers. In addition, the DSI interrupt code no longer tries to fixup write permission, this is left to generic code, and _PAGE_HWWRITE is gone. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09Merge branch 'virtex-for-2.6.27' of ↵Josh Boyer
git://git.secretlab.ca/git/linux-2.6-virtex into 4xx-next
2008-07-09powerpc/440: Convert Virtex ML507 device tree to dts-v1Grant Likely
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-09powerpc/bootwrapper: Allow user to specify additional default targetsGrant Likely
It is inconvenient to add additional default targets to the bootwrapper Makefile for each new board supported which just needs a different dts file. This change allows the defconfig to specify additional build targets. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-07-09x86: fix copy_user on x86Vitaly Mayatskikh
Switch copy_user_generic_string(), copy_user_generic_unrolled() and __copy_user_nocache() from custom tail handlers to generic copy_user_tail_handle(). Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-09x86: introduce copy_user_handle_tail() routineVitaly Mayatskikh
Introduce generic C routine for handling necessary tail operations after protection fault in copy_*_user on x86. Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-09Merge branch 'x86/unify-lib' into x86/coreIngo Molnar
2008-07-09x86: e820 memmap - add checking for NULL early paramCyrill Gorcunov
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: akpm@linux-foundation.org Cc: andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-09x86: smpboot maxcpus - add checking for NULL early paramCyrill Gorcunov
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: akpm@linux-foundation.org Cc: andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-09x86: io delay - add checking for NULL early paramCyrill Gorcunov
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: akpm@linux-foundation.org Cc: andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-09x86: idle process - add checking for NULL early paramCyrill Gorcunov
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Cc: akpm@linux-foundation.org Cc: andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-03-17 02:09:39 +0000