summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)Author
2011-03-07ARM: iomux-imx31: allow pin_list to be constUwe Kleine-König
This fixes the following warning in a mx3_defconfig build: arch/arm/mach-mx3/mach-bug.c: In function 'bug_board_init': arch/arm/mach-mx3/mach-bug.c:47: warning: passing argument 1 of 'mxc_iomux_setup_multiple_pins' discards qualifiers from pointer target type While at it remove some useless consts from unsigned int arguments. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx53_smd: Add I2C supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx25_3ds: Add I2C supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx27_3ds: Add I2C supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx31_3ds: Add I2C supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx35_3ds: Add I2C supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: Add SSI and aic3204 code to Visstrim_M10 boards.Javier Martin
Visstrim_M10 boards have an TI tlv320aic3204 codec attached to SSI1. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mx3/cpuimx35: fix build failureUwe Kleine-König
It seems vim's autocompletion played tricks on me without me noticing. This was intruduced in 97976e2 (ARM: mx3: use .init_early to initialize cpu type, reset address and iomuxer) Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: imx53_loco: add esdhc device supportRichard Zhu
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: imx51/53: add sdhc3/4 clockRichard Zhu
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07arm: mxs: tx28: add i2c bus and connected RTCWolfram Sang
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07arm: mxs: add i2c-devices for mx28Wolfram Sang
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07MX1: Add registration functions for SPI.Gwenhael Goavec-Merou
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07MX1: Add data structure for SPIGwenhael Goavec-Merou
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07MX1: Register clock for SPI2Gwenhael Goavec-Merou
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07MX1: Rename SPI interrupt name and base address.Gwenhael Goavec-Merou
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: imx35: fix trivial copy/paste errorRyan Lortie
Change imx31_add_imx_keypad() to imx35_add_imx_keypad() in mach-mx3/devices-imx35.h. Signed-off-by: Ryan Lortie <desrt@desrt.ca> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: imx35: fix ATA_DATA3 pad control addressRyan Lortie
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor Reference Manual" the correct address for the pad control register IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8. Signed-off-by: Ryan Lortie <desrt@desrt.ca> Acked-by: Marc Reilly <marc@cpdesign.com.au> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07i.MX25: add sdma clock definitionsEric Bénard
Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-07ARM: mxs: Initial support for Ka-Ro TX28Lothar Waßmann
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and me. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-07ARM: mxs: Add missing EXPORT_SYMBOL for mxs_reset_blockSascha Hauer
It is used for example in the i2c driver which can be compiled modular. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01ARM: mxs: Add pwm clocks and device registrationSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01ARM: mxc: add a dma mask to fec devicesUwe Kleine-König
This is not strictly necessary but the right thing to do. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01ARM: mxs: add a dma mask to fec devicesLothar Waßmann
This is not strictly necessary but the right thing to do. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01ARM: mxc: free dma_mask in error pathUwe Kleine-König
This fixes a small memory leak that was only hit in very unlikely error paths Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01ARM: mxs: free dma_mask in error pathLothar Waßmann
This fixes a small memory leak that was only hit in very unlikely error paths. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-03-01cpuimx51sd: mcp2515 supports up to 10MHz SPI clockEric Bénard
Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-01cpuimx51sd: fix tsc2007Eric Bénard
- wrong MUX was set before for IRQ - get_pendown_state is no more needed Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-01cpuimx51sd: add cpufreq supportEric Bénard
Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-03-01arm: mach-mx3: use IMX_GPIO_NR instead of hard-coded valuesWolfram Sang
The latter are error-prone because the bank number is one less than one would read in the documentation. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Eric Benard <eric@eukrea.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-28mx31: add support for the bugbase 1.3 from buglabsDenis 'GNUtoo' Carikli
Note that the hardware schematics and documentations can be obtained here: http://www.bugcommunity.com/wiki/index.php/BUGbase Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-28ARM: mx51_defconfig: change CONFIG_LEDS_CLASS 'm' to 'y'Shawn Guo
This patch is to fix the warning below. arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-28ARM: imx/mach-mx25_3ds: Use IMX_GPIO_NR instead of hard-coded valuesFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-28ARM: imx53: add sdhc pad settingsRichard Zhu
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-21ARM: imx53: correct Silicon Revision definition following fuse mapRichard Zhao
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-21ARM: imx53_smd add uncompress printFrank Li
Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: imx50: correct iomux-mx50.h wrong daisy chain settingsRichard Zhao
Most fix is for uart txd/cts. They don't need to select input. And fix some other pads with wrong select input. Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: imx53_loco: add i2c device supportRichard Zhao
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: imx53_loco add uncompress printRichard Zhao
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: imx53_loco: add all pad configure.Richard Zhao
Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: mach-mx5: Add watchdog support for MX53 based boardsFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18ARM: mx5: Add watchdog support for MX53Fabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18mx51: add support for efika smartbookArnaud Patard (Rtp)
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18efika: enable cpufreqArnaud Patard (Rtp)
Enable cpufreq on Genesi efika platforms Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18efikamx: add mc13892 support / implement power offArnaud Patard (Rtp)
This patch declares regulators for the efikamx. Use it also to power off the efikamx. Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to power off by setting GPIO 4 13 to high level instead of powering off through the mc13892. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18efikamx: add usb h1 supportArnaud Patard (Rtp)
Now that usb has been fixed, we can enable usb h1 on efikamx Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-18Introduce EFIKA_COMMONArnaud Patard (Rtp)
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things so it makes sense to create a common file for both devices and a specific file for each. No functionnal change except dropping uart 1 & 2. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-17ARM: mxs/mx28evk: add auart devicesShawn Guo
Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-17ARM: mxs/mx23evk: add auart deviceShawn Guo
Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-17ARM: mx23: dynamically allocate mx23 auart deviceShawn Guo
i.MX23 Reference Manaul starts auart index from 1 than 0. Changing the index to start from 0 requires corresponding changes on base address, irq, and iomux definitions, and will probably confuse people who reads codes and hardware documents together. This patch introduced the field 'hwid' to distinguish the driver id and controller id. These two ids are different on mx23 while identical on mx28. Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-28 19:31:31 +0000