| Age | Commit message (Collapse) | Author |
|---|
|
Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.
This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.
Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.
Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.
Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is wrong comment for TLB. Early printk uartlite
console uses TLB 63.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
__copy_to/from_user_inatomic should call __copy_to/from_user
because there is not necessary to check access because of kernel function.
might_sleep in copy_to/from_user macros is causing problems
in debug sessions too (CONFIG_DEBUG_SPINLOCK_SLEEP).
BUG: sleeping function called from invalid context at
.../arch/microblaze/include/asm/uaccess.h:388
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper
1 lock held by swapper/1:
#0: (&p->cred_guard_mutex){......}, at: [<c00d4b90>] prepare_bprm_creds+0x2c/0x88
Kernel Stack:
...
Call Trace:
[<c0006bd4>] microblaze_unwind+0x7c/0x94
[<c0006684>] show_stack+0xf4/0x190
[<c0006730>] dump_stack+0x10/0x30
[<c00103a0>] __might_sleep+0x12c/0x160
[<c0090de4>] file_read_actor+0x1d8/0x2a8
[<c0091568>] generic_file_aio_read+0x6b4/0xa64
[<c00cd778>] do_sync_read+0xac/0x110
[<c00ce254>] vfs_read+0xc8/0x160
[<c00d585c>] kernel_read+0x38/0x64
[<c00d5984>] prepare_binprm+0xfc/0x130
[<c00d6430>] do_execve+0x228/0x370
[<c000614c>] microblaze_execve+0x58/0xa4
caused by file_read_actor (mm/filemap.c) which calls
__copy_to_user_inatomic.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Conflicts:
tools/perf/Makefile
tools/perf/util/hist.c
Merge reason: Resolve the conflicts and update to latest upstream.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
vmx does not restore GDT.LIMIT to the host value, instead it sets it to 64KB.
This means host userspace can learn a few bits of host memory.
Fix by reloading GDTR when we load other host state.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Sometimes, atomically set spte is not needed, this patch call __xchg_spte()
more smartly
Note: if the old mapping's access bit is already set, we no need atomic operation
since the access bit is not lost
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Introduce set_spte_track_bits() to cleanup current code
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
If the old mapping is not present, the spte.a is not lost, so no need
atomic operation to set it
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
In sync-page path, if spte.writable is changed, it will lose page dirty
tracking, for example:
assume spte.writable = 0 in a unsync-page, when it's synced, it map spte
to writable(that is spte.writable = 1), later guest write spte.gfn, it means
spte.gfn is dirty, then guest changed this mapping to read-only, after it's
synced, spte.writable = 0
So, when host release the spte, it detect spte.writable = 0 and not mark page
dirty
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
In current code, if ept is enabled(shadow_accessed_mask = 0), the page
accessed tracking is lost.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
In the speculative path, we should check guest pte's reserved bits just as
the real processor does
Reported-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The index wasn't calculated correctly (off by one) for huge spte so KVM guest
was unstable with transparent hugepages.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
If the destination is a memory operand and the memory cannot
map to a valid page, the xchg instruction emulation and locked
instruction will not work on io regions and stuck in endless
loop. We should emulate exchange as write to fix it.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
If pit delivers interrupt while pic is masking it OS will never do EOI
and ack notifier will not be called so when pit will be unmasked no pit
interrupts will be delivered any more. Calling mask notifiers solves this
issue.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
With tdp enabled we should get into emulator only when emulating io, so
reexecution will always bring us back into emulator.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Mark inc (0xfe/0 0xff/0) and dec (0xfe/1 0xff/1) as lock prefix capable.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
'level' and 'sptep' are aliases for 'interator.level' and 'iterator.sptep', no
need for them.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Currently, when we fetch an spte, we only verify that gptes match those that
the walker saw if we build new shadow pages for them.
However, this misses the following race:
vcpu1 vcpu2
walk
change gpte
walk
instantiate sp
fetch existing sp
Fix by validating every gpte, regardless of whether it is used for building
a new sp or not.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Partition the function into three sections:
- fetching indirect shadow pages (host_level > guest_level)
- fetching direct shadow pages (page_level < host_level <= guest_level)
- the final spte (page_level == host_level)
Instead of the current spaghetti.
A slight change from the original code is that we call validate_direct_spte()
more often: previously we called it only for gw->level, now we also call it for
lower levels. The change should have no effect.
[xiao: fix regression caused by validate_direct_spte() called too late]
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Move the code to check whether a gpte has changed since we fetched it into
a helper.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Add a helper to verify that a direct shadow page is valid wrt the required
access permissions; drop the page if it is not valid.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
To clarify spte fetching code, move large spte handling into a helper.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
To avoid split accesses to 64 bit sptes on i386, use __set_spte() to link
shadow pages together.
(not technically required since shadow pages are __GFP_KERNEL, so upper 32
bits are always clear)
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
To simplify the process of fetching an spte, add a helper that links
a shadow page to an spte.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Userspace needs to reset and save/restore these MSRs.
The MCE banks are not exposed since their number varies from vcpu to vcpu.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Fix:
general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
......
Call Trace:
[<ffffffffa0159bd1>] ? kvm_set_irq+0xdd/0x24b [kvm]
[<ffffffff8106ea8b>] ? trace_hardirqs_off_caller+0x1f/0x10e
[<ffffffff813ad17f>] ? sub_preempt_count+0xe/0xb6
[<ffffffff8106d273>] ? put_lock_stats+0xe/0x27
...
RIP [<ffffffffa0159c72>] kvm_set_irq+0x17e/0x24b [kvm]
This bug is triggered when guest is shutdown, is because we freed
irq_routing before pit thread stopped
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
When shadow pages are in use sometimes KVM try to emulate an instruction
when it accesses a shadowed page. If emulation fails KVM un-shadows the
page and reenter guest to allow vcpu to execute the instruction. If page
is not in shadow page hash KVM assumes that this was attempt to do MMIO
and reports emulation failure to userspace since there is no way to fix
the situation. This logic has a race though. If two vcpus tries to write
to the same shadowed page simultaneously both will enter emulator, but
only one of them will find the page in shadow page hash since the one who
founds it also removes it from there, so another cpu will report failure
to userspace and will abort the guest.
Fix this by checking (in addition to checking shadowed page hash) that
page that caused the emulation belongs to valid memory slot. If it is
then reenter the guest to allow vcpu to reexecute the instruction.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Currently if guest access address that belongs to memory slot but is not
backed up by page or page is read only KVM treats it like MMIO access.
Remove that capability. It was never part of the interface and should
not be relied upon.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Stanse found that there is an omitted unlock in kvm_create_pit in one fail
path. Add proper unlock there.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Gleb Natapov <gleb@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Real hardware disregards permission errors when computing page fault error
code bit 0 (page present). Do the same.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Bit 4 of the page fault error code is set only if EFER.NX is set.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This patch change to use DstAcc for decoding 'mov AL, moffs'
and introduced SrcAcc for decoding 'mov moffs, AL'.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
If IOPL check fail, the cli/sti emulate GP and then we should
skip writeback since the default write OP is OP_REG.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The source operand of 'mov rm,sreg' is segment register, not
general-purpose register, so remove SrcReg from decoding.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
'and AL,imm8' should be mask as ByteOp, otherwise the dest operand
length will no correct and we may fill the full EAX when writeback.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Fix the comment of out instruction, using the same style as the
other instructions.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Memory reads for 'mov sreg,rm16' should be 16 bits only.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
__set_spte() will happily replace an spte with the accessed bit set with
one that has the accessed bit clear. Add a helper update_spte() which checks
for this condition and updates the page flag if needed.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Currently, in the window between the check for the accessed bit, and actually
dropping the spte, a vcpu can access the page through the spte and set the bit,
which will be ignored by the mmu.
Fix by using an exchange operation to atmoically fetch the spte and drop it.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Since we need to make the check atomic, move it to the place that will
set the new spte.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
