| Age | Commit message (Collapse) | Author |
|---|
|
This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
I forgot to separete the different names in the reg-names property. This
didn't cause anything to fail because the driver does not use the names
and simply relies on the order of the memory offsets in reg.
This patch fixes this in case it is used later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 bug fixes that should probably go into 3.11 since I'm also
tagging them for stable.
Once fixes our old /proc/powerpc/lparcfg file which provides partition
informations when running under our hypervisor and also acts as a
user-triggerable Oops when hot :-(
The other two respectively are a one liner to fix a HVSI protocol
handshake problem causing the console to fail to show up on a bunch of
machines until we reach userspace, which I deem annoying enough to
warrant going to stable, and a nasty gcc miscompile causing us to pass
virtual instead of physical addresses to the firmware under some
circumstances"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/hvsi: Increase handshake timeout from 200ms to 400ms.
powerpc: Work around gcc miscompilation of __pa() on 64-bit
powerpc: Don't Oops when accessing /proc/powerpc/lparcfg without hypervisor
|
|
The current vmlinux.lds.S places the notes sections between the
end of rw data and start of bss. This means that _edata doesn't
really point to the end of data. Since notes are read-only, this
patch moves them to the read-only segment so that _edata does
point to the end of initialized rw data.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch skips the deep C1(AFTR -Arm off top running) state for
exynos5440 SoC as this soc does not support this state. The cpu's
only allows the basic C0 state.
The C1 state is filtered by re-initialising the driver state_count
value to 1.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Currently PM domains support will be enabled for EXYNOS4X12 SoCs
only if EXYNOS4210 SoC or EXYNOS5250 SoC support is also enabled.
Fix it by explicitly selecting PM domains support (if PM support
is enabled) by SOC_EXYNOS4212 and SOC_EXYNOS4412 config options.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Enable reserved memory initialization from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
|
|
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
With OPAL v3 we can return secondary CPUs to firmware on kexec. This
allows firmware to do various cleanups making things generally more
reliable, and will enable the "new" kernel to call OPAL to perform
some reconfiguration tasks early on that can only be done while
all the CPUs are in firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch cleans the initialization of dma contiguous framework. The
all-in-one dma_declare_contiguous() function is now separated into
dma_contiguous_reserve_area() which only steals the the memory from
memblock allocator and dma_contiguous_add_device() function, which
assigns given device to the specified reserved memory area. This improves
the flexibility in defining contiguous memory areas and assigning device
to them, because now it is possible to assign more than one device to
the given contiguous memory area. Such split in initialization procedure
is also required for upcoming device tree support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
|
|
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The "rmci" stuff only exists on 64-bit
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As suggested by paulus we can simplify the Data Stream Control Register
(DSCR) Facility Status and Control Register (FSCR) handling.
Firstly, we simplify the asm by using a rldimi.
Secondly, we now use the FSCR only to control the DSCR facility, rather
than both the FSCR and HFSCR. Users will see no functional change from
this but will get a minor speedup as they will trap into the kernel only
once (rather than twice) when they first touch the DSCR. Also, this
changes removes a bunch of ugly FTR_SECTION code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge stuff that already went into Linus via "merge" which
are pre-reqs for subsequent patches
|
|
Calls to dlpar_detach_node do not iterate over child nodes detaching them as
well. By iterating and detaching the child nodes we ensure that they have the
OF_DETACHED flag set and that their reference counts are decremented such that
the node will be freed from memory by of_node_release.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The node to be detached is retrieved via its phandle by a call to
of_find_node_by_phandle which increments the ref count. We need a matching
call to of_node_put to decrement the ref count and ensure the node is
actually freed.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently the device nodes created in the device subtree returned by a call to
dlpar_configure_connector are all named in the root node. This is because the
the node name in the work area returned by ibm,configure-connector rtas call
only contains the node name and not the entire node path. Passing the parent
node where the new subtree will be created to dlpar_configure_connector allows
the correct node path to be prefixed in the full_name field.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently the OF_DYNAMIC and kref initialization for a node happens in
dlpar_attach_node. However, a node passed to dlpar_attach_node may be a tree
containing child nodes, and no initialization traversal is done on the
tree. Since the children never get their kref initialized or the OF_DYNAMIC
flag set these nodes are prevented from ever being released from memory
should they become detached. This initialization step is better done at the
time each node is allocated in dlpar_parse_cc_node.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On the first call to ibm,update-properties for a node the first property
returned is the full node path. Currently this is not parsed correctly by the
update_dt_node function. Commit 2e9b7b0 attempted to fix this, but was
incorrect as it made a wrong assumption about the layout of the first
property in the work area. Further, if ibm,update-properties must be called
multiple times for the same node this special property should only be skipped
after the initial call. The first property descriptor returned consists of
the property name, property value length, and property value. The property
name is an empty string, property length is encoded in 4 byte integer, and
the property value is the node path.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
header
The work area buffer returned by the ibm,update-properties rtas call contains
20 bytes of header information prior to the property value descriptor data.
Currently update_dt_node tries to advance over this header using sizeof(upwa).
The update_props_workarea struct contains 20 bytes worth of fields, that map
to the relevant header data, but the sizeof the structure is 24 bytes due to
4 bytes of padding at the end of the structure. Packing the structure ensures
that we don't advance too far over the rtas buffer.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The rc variable is initially used to store the return code from the
ibm,update-properties rtas call which returns 0 or 1 on success. A return
code of 1 indicates that ibm,update-properties must be called again for the
node. However, the rc variable is overwritten by a call to update_dt_prop
which returns 0 on success. This results in ibm,update-properties not being
called again for the given node when the rtas call rc was previously 1.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The update_dt_prop helper function fails to set the IN/OUT parameter prop to
NULL after a complete property has been parsed from the work area returned by
the ibm,update-properties rtas function. This results in the property list of
the device node being updated is corrupted and becomes a loop since the same
property structure is used repeatedly.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In the program check handler we handle some causes with interrupts off
and others with interrupts on.
We need to enable interrupts to handle the emulation cases, because they
access userspace memory and might sleep.
For faults in the kernel we don't want to do any emulation, and
emulate_instruction() enforces that. do_mathemu() doesn't but probably
should.
The other disadvantage of enabling interrupts for kernel faults is that
we may take another interrupt, and recurse. As seen below:
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dc10] 0000000000000000 (unreliable)
[c000000fb185dc80] c0000000007d8558 .program_check_exception+0x298/0x2d0
[c000000fb185dd00] c000000000002f40 emulation_assist_common+0x140/0x180
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dff0] 00000000008b9190 (unreliable)
[c000000fb185e060] c0000000007d8558 .program_check_exception+0x298/0x2d0
So avoid both problems by checking if the fault was in the kernel and
skipping the enable of interrupts and the emulation. Go straight to
delivering the SIGILL, which for kernel faults calls die() and so on,
dropping us in the debugger etc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This makes back traces and profiles easier to read.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The symbols that name some of our exception trampolines are ahead of the
location they name. In most cases this is OK because the code is tightly
packed, but in some cases it means the symbol floats ahead of the
correct location, eg:
c000000000000ea0 <performance_monitor_pSeries_1>:
...
c000000000000f00: 7d b2 43 a6 mtsprg 2,r13
Fix them all by moving the symbol after the set of the location.
While we're moving them anyway, rename them to loose the camelcase and
to make it clear that they are trampolines.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We haven't updated these for a while it seems, it's nice to have in the
oops output.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The spec says it "may be problematic" if CPU x registers the VPA of
CPU y. Add a warning in case we ever do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The VSX alignment handler needs to write out the existing VSX
state to memory before operating on it (flush_vsx_to_thread()).
If we take a VSX alignment exception in the kernel bad things
will happen. It looks like we could write the kernel state out
to the user process, or we could handle the kernel exception
using data from the user process (depending if MSR_VSX is set
or not).
Worse still, if the code to read or write the VSX state causes an
alignment exception, we will recurse forever. I ended up with
hundreds of megabytes of kernel stack to look through as a result.
Floating point and SPE code have similar issues but already include
a user check. Add the same check to emulate_vsx().
With this patch any unaligned VSX loads and stores in the kernel
will show up as a clear oops rather than silent corruption of
kernel or userspace VSX state, or worse, corruption of a potentially
unlimited amount of kernel memory.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As a part of pseries_idle backend driver cleanup to make
the code common to both pseries and powernv platforms, it
is necessary to move the backend-driver code to drivers/cpuidle.
As a pre-requisite for that, it is essential to move plpar_wrapper.h
to include/asm.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As a part of pseries_idle cleanup to make the backend driver
code common to both pseries and powernv.
Remove non-essential smt_snooze_delay declaration in pseries.h
header file and pseries.h file inclusion in
pseries/processor_idle.c
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The stmw instruction was incorrectly decoded as an update form instruction
and thus the RA register was being clobbered.
Also, the utility routine to write memory to unaligned addresses breaks the
operation into smaller aligned accesses but was incorrectly incrementing
the address by only one; it needs to increment the address by the size of
the smaller aligned chunk.
Signed-off-by: Tom Musta <tmusta@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Memory I/O resources need to be marked as busy or else we cannot remove
them when doing memory hot remove.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* pm-cpufreq: (60 commits)
cpufreq: pmac32-cpufreq: remove device tree parsing for cpu nodes
cpufreq: pmac64-cpufreq: remove device tree parsing for cpu nodes
cpufreq: maple-cpufreq: remove device tree parsing for cpu nodes
cpufreq: arm_big_little: remove device tree parsing for cpu nodes
cpufreq: kirkwood-cpufreq: remove device tree parsing for cpu nodes
cpufreq: spear-cpufreq: remove device tree parsing for cpu nodes
cpufreq: highbank-cpufreq: remove device tree parsing for cpu nodes
cpufreq: cpufreq-cpu0: remove device tree parsing for cpu nodes
cpufreq: imx6q-cpufreq: remove device tree parsing for cpu nodes
drivers/bus: arm-cci: avoid parsing DT for cpu device nodes
ARM: mvebu: remove device tree parsing for cpu nodes
ARM: topology: remove hwid/MPIDR dependency from cpu_capacity
of/device: add helper to get cpu device node from logical cpu index
driver/core: cpu: initialize of_node in cpu's device struture
ARM: DT/kernel: define ARM specific arch_match_cpu_phys_id
of: move of_get_cpu_node implementation to DT core library
powerpc: refactor of_get_cpu_node to support other architectures
openrisc: remove undefined of_get_cpu_node declaration
microblaze: remove undefined of_get_cpu_node declaration
cpufreq: fix bad unlock balance on !CONFIG_SMP
...
|
|
* pm-cpuidle: (25 commits)
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
cpuidle: Rearrange code and comments in get_typical_interval()
cpuidle: Ignore interval prediction result when timer is shorter
cpuidle-kirkwood.c: simplify use of devm_ioremap_resource()
cpuidle: kirkwood: Make kirkwood_cpuidle_remove function static
cpuidle: calxeda: Add missing __iomem annotation
SH: cpuidle: Add missing parameter for cpuidle_register()
ARM: ux500: cpuidle: Move ux500 cpuidle driver to drivers/cpuidle
ARM: ux500: cpuidle: Remove pointless include
ARM: ux500: cpuidle: Instantiate the driver from platform device
ARM: davinci: cpuidle: Fix target residency
cpuidle: Add Kconfig.arm and move calxeda, kirkwood and zynq
cpuidle: Check if device is already registered
cpuidle: Introduce __cpuidle_device_init()
cpuidle: Introduce __cpuidle_unregister_device()
...
|
|
* acpi-assorted:
ACPI / osl: Kill macro INVALID_TABLE().
earlycpio.c: Fix the confusing comment of find_cpio_data().
ACPI / x86: Print Hot-Pluggable Field in SRAT.
ACPI / thermal: Use THERMAL_TRIPS_NONE macro to replace number
ACPI / thermal: Remove unused macros in the driver/acpi/thermal.c
ACPI / thermal: Remove the unused lock of struct acpi_thermal
ACPI / osl: Fix osi_setup_entries[] __initdata attribute location
ACPI / numa: Fix __init attribute location in slit_valid()
ACPI / dock: Fix __init attribute location in find_dock_and_bay()
ACPI / Sleep: Fix incorrect placement of __initdata
ACPI / processor: Fix incorrect placement of __initdata
ACPI / EC: Fix incorrect placement of __initdata
ACPI / scan: Drop unnecessary label from acpi_create_platform_device()
ACPI: Move acpi_bus_get_device() from bus.c to scan.c
ACPI / scan: Allow platform device creation without any IO resources
ACPI: Cleanup sparse warning on acpi_os_initialize1()
platform / thinkpad: Remove deprecated hotkey_report_mode parameter
ACPI: Remove the old /proc/acpi/event interface
|
|
* acpi-sleep:
x86 / tboot / ACPI: Fail extended mode reduced hardware sleep
xen / ACPI: notify xen when reduced hardware sleep is available
ACPI / sleep: Introduce acpi_os_prepare_extended_sleep() for extended sleep path
|
|
* acpi-pci-hotplug: (34 commits)
ACPI / PM: Hold acpi_scan_lock over system PM transitions
ACPI / hotplug / PCI: Fix NULL pointer dereference in cleanup_bridge()
PCI / ACPI: Use dev_dbg() instead of dev_info() in acpi_pci_set_power_state()
ACPI / hotplug / PCI: Get rid of check_sub_bridges()
ACPI / hotplug / PCI: Clean up bridge_mutex usage
ACPI / hotplug / PCI: Redefine enable_device() and disable_device()
ACPI / hotplug / PCI: Sanitize acpiphp_get_(latch)|(adapter)_status()
ACPI / hotplug / PCI: Get rid of unused constants in acpiphp.h
ACPI / hotplug / PCI: Check for new devices on enabled slots
ACPI / hotplug / PCI: Allow slots without new devices to be rescanned
ACPI / hotplug / PCI: Do not check SLOT_ENABLED in enable_device()
ACPI / hotplug / PCI: Do not exectute _PS0 and _PS3 directly
ACPI / hotplug / PCI: Do not queue up event handling work items in vain
ACPI / hotplug / PCI: Consolidate slot disabling and ejecting
ACPI / hotplug / PCI: Drop redundant checks from check_hotplug_bridge()
ACPI / hotplug / PCI: Rework namespace scanning and trimming routines
ACPI / hotplug / PCI: Store parent in functions and bus in slots
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_bridge
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_func
ACPI / hotplug / PCI: Embed function struct into struct acpiphp_context
...
|
|
* pci/yijing-mps-v8:
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
PCI: Simplify pcie_bus_configure_settings() interface
PCI: Drop "PCI-E" prefix from Max Payload Size message
|
|
* pci/yinghai-assign-unassigned-v6:
PCI: Assign resources for hot-added host bridge more aggressively
PCI: Move resource reallocation code to non-__init
PCI: Delay enabling bridges until they're needed
PCI: Assign resources on a per-bus basis
PCI: Enable unassigned resource reallocation on per-bus basis
PCI: Turn on reallocation for unassigned resources with host bridge offset
PCI: Look for unassigned resources on per-bus basis
PCI: Drop temporary variable in pci_assign_unassigned_resources()
|
|
The definition of ffs() for ia64 is almost the same as
asm-generic/bitops/builtin-ffs.h. The only difference is whether it is
defined as inline function or macro function. So this switches to use
the header (both to reduce amount of arch specific code, and because
inline functions provide type-checking that macros do not).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch describe the phy used on atmel sama5d3 mother board:
- phy address
- phy interrupt pin
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the sdma driver holds the address tables for i.MX25/5 they
are no longer needed in platform_data. Remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Some toolchains (including Cavium OCTEON SDK) are emitting .eh_frame
sections by default. Discard them as they are useless in the kernel.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
... and create asm/mach-cavium-octeon/gpio.h so that things continue
to build.
This allows us to use the existing I2C connected GPIO expanders.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5632/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There were many cases of:
return something;
break;
All those break statements are unreachable and thus redundant.
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 02b849f7613003fe5f9e58bf233d49b0ebd4a5e8 ("MIPS: Get rid of the
use of .macro in C code.") replaced the macro usage but missed
the accessors in bmips.h, causing the following build error:
CC arch/mips/kernel/smp-bmips.o
{standard input}: Assembler messages:
{standard input}:951: Error: Unrecognized opcode `_ssnop'
{standard input}:952: Error: Unrecognized opcode `_ssnop'
(...)
make[6]: *** [arch/mips/kernel/smp-bmips.o] Error 1
Fix by rewriting the inline assembler using existing inline functions.
The generated code should stay unchanged.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5644/
Reviewed-by: Jonas Gorski <jogo@openwrt.org>
|
|
Fix I/O space setup, so that on non-PCI systems using inb()/outb()
won't crash the system. Some drivers may try to probe I/O space and for
that purpose we can just allocate some normal memory initially. Drivers
trying to reserve a region will fail early as we set the size to 0. If
a real I/O space is present, the PCI/PCIe support code will re-adjust
the values accordingly.
Tested with EdgeRouter Lite by enabling CONFIG_SERIO_I8042 that caused
the originally reported crash.
Reported-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5626/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
