| Age | Commit message (Collapse) | Author |
|---|
|
Support for single-step in the emulator (new in 3.12) does not work for
MMIO or PIO writes, because they are completed without returning to
the emulator. This is not worse than what we had in 3.11; still, add
comments so that the issue is not forgotten.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
These will happen due to MMIO.
Suggested-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
The map_mem() function limits the current memblock limit to PGDIR_SIZE
(the initial swapper_pg_dir mapping) to avoid create_mapping()
allocating memory from unmapped areas. However, if the first block is
within PGDIR_SIZE and not ending on a PMD_SIZE boundary, when 4K page
configuration is enabled, create_mapping() will try to allocate a pte
page. Such page may be returned by memblock_alloc() from the end of such
bank (or any subsequent bank within PGDIR_SIZE) which is not mapped yet.
The patch limits the current memblock limit to the aligned end of the
first bank and gradually increases it as more memory is mapped. It also
ensures that the start of the first bank is aligned to PMD_SIZE to avoid
pte page allocation for this mapping.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: "Leizhen (ThunderTown, Euler)" <thunder.leizhen@huawei.com>
Tested-by: "Leizhen (ThunderTown, Euler)" <thunder.leizhen@huawei.com>
|
|
The old display drivers are no longer used, and will be phased out. So
remove them from the omap2plus_defconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for AM3517EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note: the management of LCD GPIOs is unclear. They were originally muxed
as inputs, and LCD_PANEL_PWR was labelled as "dvi enable".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for Zoom board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for OMAP3 Pandora board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for OMAP3EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for 3430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for H4 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for cm-t35 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for igep0020 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for OMAP3 Stalker board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for LDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for 2430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use new display drivers for devkit8000 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use the new display drivers for Beagleboard.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use the new display drivers for RX51 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use the new display drivers for OMAP3 Overo board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note that the LCD add-on boards for lcd43 and lcd35 use the same GPIOs
for the panels. This means that both panel devices cannot be probed at
the same time.
DT will handle this correctly, i.e. the DT data will contain the panel
device only for the add-on board that is attached. However, for the
board file we need a hackish solution: We parse the kernel boot command
line, and see whether lcd43 or lcd35 is set as a default display, and
add the given one. Or, if neither is given, default to lcd43.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
4430SDP board has an option for a PicoDLP mini-projector. PicoDLP cannot
be used at the same time as the second LCD, and there are GPIOs that
need to be set/unset when changing the used display.
Managing that kind of board specific setup is not simple without board
file callbacks. As only some 4430SDP boards actually have the PicoDLP
installed, and 4430SDP boards are not that common in the first place,
let's remove PicoDLP data from the board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Use the new display drivers for OMAP4 Panda and OMAP4 SDP boards.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Add some of the most common new display drivers to omap2plus_defconfig
to be built as modules.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
This is no longer needed as omap4 is now booted using device tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
A user space program using the transactional execution facility
should be allowed to do program interrupt filtering. Do not set the
transactional-execution program-interruption-filtering override (PIFO)
bit in CR0.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For a single-threaded KVM guest ptep_modify_prot_start will not use
IPTE, the invalid bit will therefore not be set. If DEBUG_VM is set
pgste_set_key called by ptep_modify_prot_commit will complain about
the missing invalid bit. ptep_modify_prot_start should set the
invalid bit in all cases.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Modify the psw_idle waiting logic in entry[64].S to return with
interrupts disabled. This avoids potential issues with udelay
and interrupt loops as interrupts are not reenabled after
clock comparator interrupts.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This file is entirely pseries specific nowadays, so move it out
of arch/powerpc/kernel where it doesn't belong anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge recent fixes to lparcfg so subsequent patches can move
the whole file to arch/powerpc/platforms/pseries
|
|
In downstream kernel we've standardized the clock consumer names
that MSM device drivers use. Replace the uart specific clock
names in this driver with the more standard 'core' and 'iface'
names. Also simplify the code by assuming that clk_prepare_enable
and clk_disable_unprepare() will properly check for NULL pointers
(it will because MSM uses the common clock framework).
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
So I assumed that Beagle bone has only one USB port in host mode because
the micro USB connector had an USB-UART there. I was wrong a little. The
second port runs on host mode, but the micro USB plug is connected to an
internal HUB with two ports: one to the USB-UART and one to musb
instance one.
For that reason, this patch enables both ports: the primary in device
mode only and the second in host mode only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is what I observe:
On the first connect, the musb starts with DEVCTL.Session set. On
disconnect, musb_core calls try_idle. That functions removes the Session
bit signalizing that the session is over (something that only in OTG is
required). A new device, that is plugged, is no longer recognized.
I've setup a timer and checked the DEVCTL register and I haven't seen a
change in VBus and I saw the B-Device bit set. After setting the IDDIG
into A mode and forcing the device to behave like a A device, I didn't
see a change.
Neither VBUS goes to 0b11 nor does a session start request comes.
In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the
OTG_STATE_A_WAIT_BCON state while not in OTG mode.
Since the second port hast a standard A plug the patch changes the port
to run in host mode only and skips the timer which would remove
DEVCTL.Session so we can reconnect to another device later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
I forgot to separete the different names in the reg-names property. This
didn't cause anything to fail because the driver does not use the names
and simply relies on the order of the memory offsets in reg.
This patch fixes this in case it is used later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 bug fixes that should probably go into 3.11 since I'm also
tagging them for stable.
Once fixes our old /proc/powerpc/lparcfg file which provides partition
informations when running under our hypervisor and also acts as a
user-triggerable Oops when hot :-(
The other two respectively are a one liner to fix a HVSI protocol
handshake problem causing the console to fail to show up on a bunch of
machines until we reach userspace, which I deem annoying enough to
warrant going to stable, and a nasty gcc miscompile causing us to pass
virtual instead of physical addresses to the firmware under some
circumstances"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/hvsi: Increase handshake timeout from 200ms to 400ms.
powerpc: Work around gcc miscompilation of __pa() on 64-bit
powerpc: Don't Oops when accessing /proc/powerpc/lparcfg without hypervisor
|
|
The current vmlinux.lds.S places the notes sections between the
end of rw data and start of bss. This means that _edata doesn't
really point to the end of data. Since notes are read-only, this
patch moves them to the read-only segment so that _edata does
point to the end of initialized rw data.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch skips the deep C1(AFTR -Arm off top running) state for
exynos5440 SoC as this soc does not support this state. The cpu's
only allows the basic C0 state.
The C1 state is filtered by re-initialising the driver state_count
value to 1.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Currently PM domains support will be enabled for EXYNOS4X12 SoCs
only if EXYNOS4210 SoC or EXYNOS5250 SoC support is also enabled.
Fix it by explicitly selecting PM domains support (if PM support
is enabled) by SOC_EXYNOS4212 and SOC_EXYNOS4412 config options.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Enable reserved memory initialization from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
|
|
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
With OPAL v3 we can return secondary CPUs to firmware on kexec. This
allows firmware to do various cleanups making things generally more
reliable, and will enable the "new" kernel to call OPAL to perform
some reconfiguration tasks early on that can only be done while
all the CPUs are in firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch cleans the initialization of dma contiguous framework. The
all-in-one dma_declare_contiguous() function is now separated into
dma_contiguous_reserve_area() which only steals the the memory from
memblock allocator and dma_contiguous_add_device() function, which
assigns given device to the specified reserved memory area. This improves
the flexibility in defining contiguous memory areas and assigning device
to them, because now it is possible to assign more than one device to
the given contiguous memory area. Such split in initialization procedure
is also required for upcoming device tree support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
|
|
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The "rmci" stuff only exists on 64-bit
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As suggested by paulus we can simplify the Data Stream Control Register
(DSCR) Facility Status and Control Register (FSCR) handling.
Firstly, we simplify the asm by using a rldimi.
Secondly, we now use the FSCR only to control the DSCR facility, rather
than both the FSCR and HFSCR. Users will see no functional change from
this but will get a minor speedup as they will trap into the kernel only
once (rather than twice) when they first touch the DSCR. Also, this
changes removes a bunch of ugly FTR_SECTION code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge stuff that already went into Linus via "merge" which
are pre-reqs for subsequent patches
|
|
Calls to dlpar_detach_node do not iterate over child nodes detaching them as
well. By iterating and detaching the child nodes we ensure that they have the
OF_DETACHED flag set and that their reference counts are decremented such that
the node will be freed from memory by of_node_release.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The node to be detached is retrieved via its phandle by a call to
of_find_node_by_phandle which increments the ref count. We need a matching
call to of_node_put to decrement the ref count and ensure the node is
actually freed.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently the device nodes created in the device subtree returned by a call to
dlpar_configure_connector are all named in the root node. This is because the
the node name in the work area returned by ibm,configure-connector rtas call
only contains the node name and not the entire node path. Passing the parent
node where the new subtree will be created to dlpar_configure_connector allows
the correct node path to be prefixed in the full_name field.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
