summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)Author
2013-08-22ARM: dts: i.MX51: Add one more I2C2 pinmux entryAlexander Shiyan
This adds one more I2C2 alternate pinmux entry. GPIO1_2 <=> SCL GPIO1_3 <=> SDA Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX51: Move pins configuration under "iomuxc" labelAlexander Shiyan
This unmix module/pin definitions and reduce indentation for pin groups, so makes template a bit cleaner. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hogPeter Chen
USB OTG vbus pin needs to be configured as gpio function at sabresd board. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulatorPeter Chen
We enabled USB host 1, so host 1's vbus should be on to let host 1 work. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27-phytec-phycore-som: Enable AUDMUXAlexander Shiyan
Patch adds AUDMUX routing for Phytec PCM-038 module. This route i.MX SSI0 (Port 1) to the slave port 4 where MC13783 codec interface is connected. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Disable AUDMUX in the templateAlexander Shiyan
AUDMUX expects additional parameters to be configured correctly, so turn it off into a template. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: wandboard: Add support for SDIO bcm4329Tony Prisk
The wandboard has a Broadcom 4329 WiFi connected via SDIO. This patch sets the required pins to enable the wifi module. Signed-off-by: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 templateAlexander Shiyan
External high frequency clock CKIH1 is optional for i.MX51, so move it setup into boards where it is used. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx53-qsb: Make USBH1 functionalFabio Estevam
mx53qsb uses GPIO7_8 to turn on VBUS, so add support for it. Also specify the PHY type in the device tree. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 ↵Philipp Zabel
Ouad module This patch enables I2C1 and adds device tree nodes for the EEPROM and the DA9063 PMIC connected to this I2C bus. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad modulePhilipp Zabel
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl-sabresd: Add touchscreen supportFabio Estevam
mx6 sabresd boards have a egalax touchscreen controller connected via I2C3. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: imx: add ocram clock for imx53Shawn Guo
Add missing ocram gate clock for imx53 and also represent it in device tree ocram node. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: ocram size is different between imx6q and imx6dlShawn Guo
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB. Let's have separate node for imx6q and imx6dl. It also changes imx6q size 0x3f000 to 0x40000 to match the hardware. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Liu Ying <Ying.Liu@freescale.com>
2013-08-22ARM: dts: imx27-phytec-phycore-som: Fix regulator settingsAlexander Shiyan
Outputs regulator SW1A and SW1A, SW2A and SW2B are connected together, so it determined as "joined" operation for MC13783. Separate work of these outputs in this case would be wrong, so we define only one of the outputs. Additionally, define the full range of voltages for the CPU (1.2v - 1.52v). Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Remove clock name from CPU nodeAlexander Shiyan
Clock name is not needed for "cpufreq-cpu0". Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Increase "clock-latency" valueAlexander Shiyan
i.MX27 CPU can be clocked with a 32 kHz quartz, and not just 32768 Hz, so increase "clock-latency" value, which will ensure that we use two clock cycles on frequency change. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Add label to CPU nodeAlexander Shiyan
Add a label to i.MX27 CPU node. This change allows the reuse this node in the upper levels of the DTS. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Remove optional "ptp" clock source for FECAlexander Shiyan
Patch removes optional "ptp" clock source for FEC. This clock is missing in i.MX27. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX27: Using "wdog_ipg_gate" clock source for watchdogAlexander Shiyan
Patch replaces "dummy" clock source for watchdog with "wdog_ipg_gate". Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl-sabresd: Allow buttons to wake-up the systemFabio Estevam
This is useful for testing suspend/resume sequence. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: imx6q: remove board specific CLKO setupShawn Guo
The CLKO is widely used by imx6q board designs to clock audio codec. Since most codecs accept 24 MHz frequency, let's initially set up CLKO with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO setup for audio codec can be removed. The board dts files also need an update on cko reference in codec node. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: use generic DMA bindings for SSI nodesShawn Guo
Updates SSI nodes to adopt generic DMA bindings. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: add LVDS panel for imx6qdl-sabresdShawn Guo
Add HannStar HSD100PXN1 XGA panel support on LVDS1 port of imx6qdl-sabresd board. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6q-wandboard: Add sata supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6: Add support for imx6q wandboardFabio Estevam
Add support for the imx6q wanboard variant. Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi file that contains the common peripheral nodes. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: add tempmon node for imx6q thermal supportShawn Guo
Mark ocotp as a syscon node and add tempmon for imx6q thermal support. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: remove old DMA binding data from gpmi nodeShawn Guo
After mxs-dma driver adopts generic DMA device tree binding, gpmi channel interrupt number is defined in DMA controller node, and channel ID is listed in "dmas" property. So the DMA channel interrupt number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which are used by old customized DMA binding can be removed now. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2013-08-22ARM: dtsi: enable ahci sata on imx6q platformsRichard Zhu
Only imx6q has the ahci sata controller, enable it on imx6q platforms. Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27: Add core voltagesAlexander Shiyan
This patch adds core voltages for i.MX27 CPUs. Only 266 and 400 MHz modes is documented in the datasheet, so we add a 266 MHz frequency for conform this. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: i.MX51: Add WEIM nodeAlexander Shiyan
This patch adds the missing (Wireless External Interface Module) WEIM devicetree node for i.MX51 CPUs. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6dl-wandboard: Add support for UART3Fabio Estevam
Wandboard has a bluetooth device connected to UART3, so add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6dl-wandboard: Add SDHC1 and SDHC2 portsFabio Estevam
Wandboard has a SD card slot on the baseboard connected to SDHC1 and a BCM4329 (Wifi + Bluetooth chip) connected to SDHC2. Add support for these ports. While at it, provide the card detect gpio on SDHC3 and also fix indentation on MX6QDL_PAD_GPIO_0__CCM_CLKO1 hog pin. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl.dtsi: Add another uart3 pin groupFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl.dtsi: Add usdhc1 pin groupsFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl/imx6sl: add the dma property for uartHuang Shijie
Add the dma property for all the uart. Note: Add the dma property does not mean we enable the dma for this uart. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx25: Make lcdc compatible to imx21 fbMatthias Weisser
Make lcdc compatible to imx21 fb. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6qdl: add a new pinctrl for uart3Huang Shijie
Add the a new pinctrl for uart3. In the imx6q{dl}-sabreauto boards, the uart3 is used for Bluetooth. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: add more imx6q/dl pin groupsShawn Guo
Add more imx6q/dl pin groups for those supported boards, e.g. sabresd, sabreauto, arm2. IPU2 pin groups are added into imx6q.dtsi, since the block is only available on imx6q. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: share pad macro names between imx6q and imx6dlShawn Guo
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board design can work with either chip plugged into the socket, e.g. sabresd and sabreauto boards. We currently define pin groups in imx6q.dtsi and imx6dl.dtsi respectively because the pad macro names are different between two chips. This brings a maintenance burden on having the same label point to the same pin group defined in two places. The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs pad macro names. Then the pin groups becomes completely common between imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the long term maintenance of imx6q/dt pin settings becomes easier. Unfortunately, the change brings some dramatic diff stat, but it's all about DTS file, and the ultimate net diff stat is good. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: enable the uart2 for imx6q-arm2Huang Shijie
enable the uart2 for imx6q-arm2 board. The uart2 works in the DTE mode, with the RTS/CTS and DMA enabled. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6q{dl}: add a DTE uart pinctrl for uart2Huang Shijie
In the arm2 board, the UART2 works in the dte mode. So add a pinctrl for both the imx6q{dl} boards. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6q{dl}: add DTE pads for uartHuang Shijie
The uart2 in the imx6q-arm2 board is used as a DTE uart, this patch adds the necessary DTE pads for uart2. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6sl: add "fsl,imx6q-uart" for uart compatibleHuang Shijie
In order to enable the DMA for some uart port in imx6sl, we add the "fsl,imx6q-uart" to the uart's compatible property. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27 phyCARD-S, i2c ADC device nodeMarkus Pargmann
Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27 phyCARD-S, move i2c1 and owire to rdkMarkus Pargmann
Both buses are not used on the phyCARD-S module. This patch moves them to the rdk file. Remove ioexpander. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27 phyCARD-S SOM remove wrong i2c sensorMarkus Pargmann
This sensor was introduced in the original pca100 board file, but phyCARD-S SOM and RDK do not have a temperature sensor. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx: Add the missing cpus nodeFabio Estevam
To make it consistent with the other i.mx SoCs, let's add the cpus nodes. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx6dl-wandboard: Add audio supportFabio Estevam
Wandboard has a sgtl5000 codec. Add audio support. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22ARM: dts: imx27 phyCARD-S remove wrong I2C RTCMarkus Pargmann
Fixup of commit "ARM: dts: Add device tree support for phycard pca100". Remove wrong I2C RTC node. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-03-16 23:21:30 +0000