| Age | Commit message (Collapse) | Author |
|---|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:
- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.
- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.
Further, vdda_lli is supposed to be 1.5V and not 3V.
- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi
This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.
- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.
- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".
So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.
Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.
- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
|
|
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
|
|
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
|
|
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
- lots of devm_ conversions and cleanup
- platform_set_drvdata cleanups
- s3c2410: dev_err/dev_info + dev_pm_ops
- watchdog_core: don't try to stop device if not running fix
- wdrtas: use print_hex_dump
- xilinx cleanups
- orion_wdt fixes
- softdog cleanup
- hpwdt: check on UEFI bits
- deletion of mpcore_wdt driver
- addition of broadcom BCM2835 watchdog timer driver
- addition of MEN A21 watcdog devices
* git://www.linux-watchdog.org/linux-watchdog: (38 commits)
watchdog: hpwdt: Add check for UEFI bits
watchdog: softdog: remove replaceable ping operation
watchdog: New watchdog driver for MEN A21 watchdogs
Watchdog: fix clearing of the watchdog interrupt
Watchdog: allow orion_wdt to be built for Dove
watchdog: Add Broadcom BCM2835 watchdog timer driver
watchdog: delete mpcore_wdt driver
watchdog: xilinx: Setup the origin compatible string
watchdog: xilinx: Fix driver header
watchdog: wdrtas: don't use custom version of print_hex_dump
watchdog: core: don't try to stop device if not running
watchdog: jz4740: Pass device to clk_get
watchdog: twl4030: Remove redundant platform_set_drvdata()
watchdog: mpcore: Remove redundant platform_set_drvdata()
watchdog: da9055: use platform_{get,set}_drvdata()
watchdog: da9052: use platform_{get,set}_drvdata()
watchdog: cpwd: use platform_{get,set}_drvdata()
watchdog: s3c2410_wdt: convert s3c2410wdt to dev_pm_ops
watchdog: s3c2410_wdt: use dev_err()/dev_info() instead of pr_err()/pr_info()
watchdog: wm831x: use platform_{get,set}_drvdata()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
|
|
[suggested by Rasmus Villemoes] make O_DIRECTORY | O_RDWR part of O_TMPFILE;
that will fail on old kernels in a lot more cases than what I came up with.
And make sure O_CREAT doesn't get there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
OMAP recently changed how the platforms are configured, so OMAP2/3/4 SoC
support is no longer enabled by default. Add them back.
Enable new ethernet driver for sunxi.
The i.MX console options moved due to resorting, no functional change.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Russell King <linux@arm.linux.org.uk>
[olof: squashed three commits down to one]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
|
|
This that should have been fixed but weren't, way to much, intrusive
and late.
|
|
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
http://lkml.kernel.org/r/20130704223010.GA30625@quad
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20130708214404.B0B6EA66@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull Xtensa updates from Chris Zankel.
* tag 'xtensa-next-20130710' of git://github.com/czankel/xtensa-linux: (22 commits)
xtensa: remove the second argument of __bio_kmap_atomic()
xtensa: add static function tracer support
xtensa: Flat DeviceTree copy not future-safe
xtensa: check TLB sanity on return to userspace
xtensa: adjust boot parameters address when INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX is selected
xtensa: bootparams: fix typo
xtensa: tell git to ignore generated .dtb files
xtensa: ccount based sched_clock
xtensa: ccount based clockevent implementation
xtensa: consolidate ccount access routines
xtensa: cleanup ccount frequency tracking
xtensa: timex.h: remove unused symbols
xtensa: tell git to ignore copied zlib source files
xtensa: fix section mismatch in pcibios_fixup_bus
xtensa: ISS: fix section mismatch in iss_net_setup
arch: xtensa: include: asm: compiling issue, need cmpxchg64() defined.
xtensa: xtfpga: fix section mismatch
xtensa: remove unused platform_init_irq()
xtensa: tell git to ignore generated files
xtensa: flush TLB entries for pages of non-current mm correctly
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
|
|
Pull more KVM changes from Gleb Natapov:
"A fix for a bug that prevents some guests from working on old Intel
CPUs and a patch that integrates ARM64 KVM, merged via ARM64 tree,
into Kconfig."
* tag 'kvm-3.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: mark unusable segment as nonpresent
arm64: KVM: Kconfig integration
|
|
Pull Sparc bugfixes from David Miller:
"Four bug fixes:
1) Enable snoop tags properly on Sparc32/LEON, from Andreas Larsson
2) strcpy() length check fix from Chen Gang.
3) Forgotten unregister_netdev() in sunvnet driver, from Dave
Kleikamp.
4) Fix broken assembler offsets used in vm_area_struct accesses on
sparc32, from Olivier DANET."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
[PATCH] sparc32: vm_area_struct access for old Sun SPARCs.
sunvnet: vnet_port_remove must call unregister_netdev
sparc32, leon: Require separate snoop tags set to regard snooping to be enabled
arch: sparc: kernel: check the memory length before use strcpy().
|
|
Merge more patches from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: remove free_area_cache
zswap: add documentation
zswap: add to mm/
zbud: add to mm/
|
|
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two small fixlets"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix interrupt handler timing harness
perf/x86/amd: Do not print an error when the device is not present
|
|
Commit e4c6bfd2d79d063017ab19a18915f0bc759f32d9 ("mm: rearrange
vm_area_struct for fewer cache misses") changed the layout of the
vm_area_struct structure, it broke several SPARC32 assembly routines
which used numerical constants for accessing the vm_mm field.
This patch defines the VMA_VM_MM constant to replace the immediate values.
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if data snooping is enabled, without separate snoop tags snooping will not
work when the MMU is enabled.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the related next strcpy(), the destination length is less than 512,
but the source maximize length may be 'OPROMMAXPARAM' (4096) which is
more than 512.
One work flow may:
openprom_sunos_ioctl() -> if (cmd == OPROMSETOPT)
getstrings() -> will alloc buffer with size 'OPROMMAXPARAM'.
opromsetopt() -> devide the buffer into 'var' and 'value'
of_set_property() -> pass
prom_setprop() -> pass
ldom_set_var()
And do not mind the additional 4 alignment buffer increasing, since
'sizeof(pkt) - sizeof(pkt.header)' is 4 alignment at least.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.11:
Core:
- Add support for eMMC 5.1 devices
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
management of eMMC/SD between requests, using runtime PM
- Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code
at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
- dw_mmc: Add support for Altera SoCFPGAs
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
cards
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
- sdhi/tmio: Add DT DMA support"
* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
mmc: bcm281xx SDHCI driver
mmc: sdhci: add card_event callback to sdhci
mmc: core: Fixup Oops for SDIO shutdown
mmc: sdhci-pci: add another device id
mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
mmc: esdhc: Add support for 8-bit bus width and non-removable card
mmc: core: production year for eMMC 4.41 and later
mmc: omap: remove unnecessary #if 0's
mmc: sdhci: fix ctrl_2 on super-speed selection
mmc: dw_mmc-pltfm: add Rockchip variant
mmc: dw_mmc-pltfm: move probe and remove below dt match table
mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
mmc: sdhci: fix caps2 for HS200
sdhci-pxav3: Fix runtime PM initialization
mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Enable power_off_notify for eMMC shutdown sequence
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For the 3.11 merge we only have one new MFD driver for the Kontron
PLD.
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator
subdevice addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need
since commit 0998d0631001 ("device-core: Ensure drvdata = NULL when
no driver is bound")
* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
mfd: sec: Provide max_register to regmap
mfd: wm8994: Remove duplicate check for active JACKDET
MAINTAINERS: Add include directory to MFD file patterns
mfd: sec: Remove fields not used since regmap conversion
watchdog: Kontron PLD watchdog timer driver
mfd: max8998: Add support for Device Tree
regulator: max8998: Use arrays for specifying voltages in platform data
mfd: max8998: Add irq domain support
regulator: palmas: Add TPS659038 support
mfd: Kontron PLD mfd driver
mfd: palmas: Add TPS659038 PMIC support
mfd: palmas: Add SMPS10_BOOST feature
mfd: palmas: Check if irq is valid
mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
mfd: twl-core: Change TWL6025 references to TWL6032
mfd: davinci_voicecodec: Fix build breakage
mfd: vexpress: Make the driver optional for arm and arm64
mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
mfd: davinci_voicecodec: Convert to use devm_* APIs
mfd: twl4030-power: Fix relocking on error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"irq-tracing fixlet"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tracing: Add irq_enter/exit() in smp_trace_reschedule_interrupt()
|
|
Pull microblaze update from Michal Simek:
"This Microblaze merge window is quite minimal.
I have also added to my branch one xilinx systemace sparse fix because
haven't got any reply from block maintainer."
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
xilinx systemace: Fix sparse warnings
microblaze: Move __NR_syscalls from uapi
microblaze: Enable KGDB in defconfig
microblaze: Don't mark arch_kgdb_ops as const.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fixes from James Hogan:
"This is just a single fix to fix bad UDP checksums sometimes being
generated to IP addresses *.*.255.255"
* tag 'metag-fixes-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: checksum.h: fix carry in csum_tcpudp_nofold
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao:
"blackfin updates for Linux 3.11"
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
smp: refine bf561 smpboot code
bf609: stmmac: fix build after stmmac_mdio_bus_data changed
bf609: add cpu revision 0.1
bf609: rename bfin6xx_spi to bfin_spi3
kgdb: blackfin: include irq_regs.h in kgdb.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of ARC architecture updates from Vineet Gupta:
"Couple of Platform updates (Device Tree files primarily) given that
the corresponding drivers (net/ethernet/arc/*, irqctl/irq-tb10x.c)
have now been merged into your tree.
Ideally these shd have been part of same submissions, oh well..."
* tag 'arc-v3.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [TB10x] Updates for irqchip driver
ARC: [plat-arcfpga] Enable arc_emac for ARCAngle4 Board
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The PA-RISC updates for v3.11 include a gcc miscompilation fix,
gzip-compressed vmlinuz support, a fix in the PCI code for ATI FireGL
support on c8000 machines, a fix to prevent that %sr1 is being
clobbered and a few smaller optimizations and documentation updates"
* 'parisc-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix gcc miscompilation in pa_memcpy()
parisc: Ensure volatile space register %sr1 is not clobbered
parisc: optimize mtsp(0,sr) inline assembly
parisc: switch to gzip-compressed vmlinuz kernel
parisc: document the shadow registers
parisc: more capabilities info in /proc/cpuinfo
parisc: fix LMMIO mismatch between PAT length and MASK register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
P{ill ia64 warning fix from Tony Luck:
"Add some casts to avoid warnings from efi_runtime_services_t members"
* tag 'please-pull-fix-ia64-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] sim: Add casts to avoid assignment warnings
|
|
The reason is that other applications like strace
think that every __NR_xx is syscall.
Also __NR_syscalls is not used by user applications/libs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a999 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
|
|
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
|
|
When the local timer freq changed, the twd_update_frequency function
should be run all the CPUs include itself, otherwise, the twd freq will
not get updated and the local timer will not run correcttly.
smp_call_function will run functions on all other CPUs, but not include
himself, this is not correct,use on_each_cpu instead to fix this issue.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
imx_v6_v7_defconfig handles both multi-core and single-core SoCs, and it has CONFIG_SMP=y selected by default.
With such config we cannot select ARM_ERRATA_364296, as it depends on !SMP.
Let ARM_ERRATA_364296 be undependent on CONFIG_SMP, so that we can select this erratum for the ARM1136 SoCs, even if CONFIG_SMP=y is enabled.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When running the LTP testsuite one may hit this kernel BUG() with the
write06 testcase:
kernel BUG at mm/filemap.c:2023!
CPU: 1 PID: 8614 Comm: writev01 Not tainted 3.10.0-rc7-64bit-c3000+ #6
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000401e6e84 00000000401e6e88
IIR: 03ffe01f ISR: 0000000010340000 IOR: 000001fbe0380820
CPU: 1 CR30: 00000000bef80000 CR31: ffffffffffffffff
ORIG_R28: 00000000bdc192c0
IAOQ[0]: iov_iter_advance+0x3c/0xc0
IAOQ[1]: iov_iter_advance+0x40/0xc0
RP(r2): generic_file_buffered_write+0x204/0x3f0
Backtrace:
[<00000000401e764c>] generic_file_buffered_write+0x204/0x3f0
[<00000000401eab24>] __generic_file_aio_write+0x244/0x448
[<00000000401eadc0>] generic_file_aio_write+0x98/0x150
[<000000004024f460>] do_sync_readv_writev+0xc0/0x130
[<000000004025037c>] compat_do_readv_writev+0x12c/0x340
[<00000000402505f8>] compat_writev+0x68/0xa0
[<0000000040251d88>] compat_SyS_writev+0x98/0xf8
Reason for this crash is a gcc miscompilation in the fault handlers of
pa_memcpy() which return the fault address instead of the copied bytes.
Since this seems to be a generic problem with gcc-4.7.x (and below), it's
better to simplify the fault handlers in pa_memcpy to avoid this problem.
Here is a simple reproducer for the problem:
int main(int argc, char **argv)
{
int fd, nbytes;
struct iovec wr_iovec[] = {
{ "TEST STRING ",32},
{ (char*)0x40005000,32} }; // random memory.
fd = open(DATA_FILE, O_RDWR | O_CREAT, 0666);
nbytes = writev(fd, wr_iovec, 2);
printf("return value = %d, errno %d (%s)\n",
nbytes, errno, strerror(errno));
return 0;
}
In addition, John David Anglin wrote:
There is no gcc PR as pa_memcpy is not legitimate C code. There is an
implicit assumption that certain variables will contain correct values
when an exception occurs and the code randomly jumps to one of the
exception blocks. There is no guarantee of this. If a PR was filed, it
would likely be marked as invalid.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.8+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
I still see the occasional random segv on rp3440. Looking at one of
these (a code 15), it appeared the problem must be with the cache
handling of anonymous pages. Reviewing this, I noticed that the space
register %sr1 might be being clobbered when we flush an anonymous page.
Register %sr1 is used for TLB purges in a couple of places. These
purges are needed on PA8800 and PA8900 processors to ensure cache
consistency of flushed cache lines.
The solution here is simply to move the %sr1 load into the TLB lock
region needed to ensure that one purge executes at a time on SMP
systems. This was already the case for one use. After a few days of
operation, I haven't had a random segv on my rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
If the value which should be moved into a space register is zero, we can
optimize the inline assembly to become "mtsp %r0,%srX".
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
|
|
The latest PA-RISC Boot Loader (palo) allows loading of gzip compressed
vmlinuz kernels. So let's now switch to build a vmlinuz file when we
build a palo boot image.
PALO version 1.9 (or higher) is required for this which is available at
git://git.kernel.org/pub/scm/linux/kernel/git/deller/palo.git
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
|
|
Integrates the LZ4 decompression code to the arm pre-boot code.
Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Yann Collet <yann.collet.73@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
