| Age | Commit message (Collapse) | Author |
|---|
|
Manual fixup of:
arch/powerpc/Kconfig
|
|
The new dma_attrs support must only be enabled for 64 bits as it's not
been implemented for 32 bits yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Push the sync below the secondary smp init hold loop and comment its purpose.
This should speed up boot by reducing global traffic during the single-threaded
portion of boot.
Signed-off-by: Sonny Rao <sonnyrao@us.ibm.com>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
VSX loads and stores will take an alignment exception when the address
is not on a 4 byte boundary.
This add support for these alignment exceptions and will emulate the
requested load or store.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
giveup_vsx didn't save the FPU and VMX regsiters. Change it to be
like giveup_fpr/altivec which save these registers.
Also update call sites where FPU and VMX are already saved to use the
original giveup_vsx (renamed to __giveup_vsx).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Implement save_stack_trace_tsk on powerpc, so that we can run with
latencytop.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
It is okay for both _PAGE_GUARDED and _PAGE_COHERENT (G and M) to be set
in the same pte. In fact, even if that were not the case, there doesn't
seem to be any place where G is set without also setting I (_PAGE_NO_CACHE),
so the test for I is sufficient as a condition to clear _PAGE_COHERENT
when filling the hash table.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Background from Maynard Johnson:
As of POWER6, a set of 32 common events is defined that must be
supported on all future POWER processors. The main impetus for this
compat set is the need to support partition migration, especially from
processor P(n) to processor P(n+1), where performance software that's
running in the new partition may not be knowledgeable about processor
P(n+1). If a performance tool determines it does not support the
physical processor, but is told (via the
PPC_FEATURE_PSERIES_PERFMON_COMPAT bit) that the processor supports
the notion of the PMU compat set, then the performance tool can
surface just those events to the user of the tool.
PPC_FEATURE_PSERIES_PERFMON_COMPAT indicates that the PMU supports at
least this basic subset of events which is compatible across POWER
processor lines.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Adds a character driver for BSR support on IBM POWER systems including
Power5 and Power6. The BSR is an optional processor facility not currently
implemented by any other processors. It's primary purpose is fast large SMP
synchronization. More details on the BSR are in comments to the code which
follows. This patch adds BSR driver to pseries_defconfig.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
|
|
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc55d20536fbdceb6131f38e288541e0 depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/rodata' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
move BUG_TABLE into RODATA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, generic: mark early_printk as asmlinkage
printk: export console_drivers
printk: remember the message level for multi-line output
printk: refactor processing of line severity tokens
printk: don't prefer unsuited consoles on registration
printk: clean up recursion check related static variables
namespacecheck: more kernel/printk.c fixes
namespacecheck: fix kernel printk.c
|
|
Even the help-text makes it clear that normal people shouldn't enable
it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (228 commits)
ftrace: build fix for ftraced_suspend
ftrace: separate out the function enabled variable
ftrace: add ftrace_kill_atomic
ftrace: use current CPU for function startup
ftrace: start wakeup tracing after setting function tracer
ftrace: check proper config for preempt type
ftrace: trace schedule
ftrace: define function trace nop
ftrace: move sched_switch enable after markers
ftrace: prevent ftrace modifications while being kprobe'd, v2
fix "ftrace: store mcount address in rec->ip"
mmiotrace broken in linux-next (8-bit writes only)
ftrace: avoid modifying kprobe'd records
ftrace: freeze kprobe'd records
kprobes: enable clean usage of get_kprobe
ftrace: store mcount address in rec->ip
ftrace: build fix with gcc 4.3
namespacecheck: fixes
ftrace: fix "notrace" filtering priority
ftrace: fix printout
...
|
|
* 'bkl-removal' of git://git.lwn.net/linux-2.6: (146 commits)
IB/umad: BKL is not needed for ib_umad_open()
IB/uverbs: BKL is not needed for ib_uverbs_open()
bf561-coreb: BKL unneeded for open()
Call fasync() functions without the BKL
snd/PCM: fasync BKL pushdown
ipmi: fasync BKL pushdown
ecryptfs: fasync BKL pushdown
Bluetooth VHCI: fasync BKL pushdown
tty_io: fasync BKL pushdown
tun: fasync BKL pushdown
i2o: fasync BKL pushdown
mpt: fasync BKL pushdown
Remove BKL from remote_llseek v2
Make FAT users happier by not deadlocking
x86-mce: BKL pushdown
vmwatchdog: BKL pushdown
vmcp: BKL pushdown
via-pmu: BKL pushdown
uml-random: BKL pushdown
uml-mmapper: BKL pushdown
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (821 commits)
x86: make 64bit hpet_set_mapping to use ioremap too, v2
x86: get x86_phys_bits early
x86: max_low_pfn_mapped fix #4
x86: change _node_to_cpumask_ptr to return const ptr
x86: I/O APIC: remove an IRQ2-mask hack
x86: fix numaq_tsc_disable calling
x86, e820: remove end_user_pfn
x86: max_low_pfn_mapped fix, #3
x86: max_low_pfn_mapped fix, #2
x86: max_low_pfn_mapped fix, #1
x86_64: fix delayed signals
x86: remove conflicting nx6325 and nx6125 quirks
x86: Recover timer_ack lost in the merge of the NMI watchdog
x86: I/O APIC: Never configure IRQ2
x86: L-APIC: Always fully configure IRQ0
x86: L-APIC: Set IRQ0 as edge-triggered
x86: merge dwarf2 headers
x86: use AS_CFI instead of UNWIND_INFO
x86: use ignore macro instead of hash comment
x86: use matching CFI_ENDPROC
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (50 commits)
crypto: ixp4xx - Select CRYPTO_AUTHENC
crypto: s390 - Respect STFL bit
crypto: talitos - Add support for sha256 and md5 variants
crypto: hash - Move ahash functions into crypto/hash.h
crypto: crc32c - Add ahash implementation
crypto: hash - Added scatter list walking helper
crypto: prng - Deterministic CPRNG
crypto: hash - Removed vestigial ahash fields
crypto: hash - Fixed digest size check
crypto: rmd - sparse annotations
crypto: rmd128 - sparse annotations
crypto: camellia - Use kernel-provided bitops, unaligned access helpers
crypto: talitos - Use proper form for algorithm driver names
crypto: talitos - Add support for 3des
crypto: padlock - Make module loading quieter when hardware isn't available
crypto: tcrpyt - Remove unnecessary kmap/kunmap calls
crypto: ixp4xx - Hardware crypto support for IXP4xx CPUs
crypto: talitos - Freescale integrated security engine (SEC) driver
[CRYPTO] tcrypt: Add self test for des3_ebe cipher operating in cbc mode
[CRYPTO] rmd: Use pointer form of endian swapping operations
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (31 commits)
avr32: Fix typo of IFSR in a comment in the PIO header file
avr32: Power Management support ("standby" and "mem" modes)
avr32: Add system device for the internal interrupt controller (intc)
avr32: Add simple SRAM allocator
avr32: Enable SDRAMC clock at startup
rtc-at32ap700x: Enable wakeup
macb: Basic suspend/resume support
atmel_serial: Drain console TX shifter before suspending
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
avr32: Use a quicklist for PTE allocation as well
avr32: Use a quicklist for PGD allocation
avr32: Cover the kernel page tables in the user PGDs
avr32: Store virtual addresses in the PGD
avr32: Remove useless zeroing of swapper_pg_dir at startup
avr32: Clean up and optimize the TLB operations
avr32: Rename at32ap.c -> pdc.c
avr32: Move setup_platform() into chip-specific file
avr32: Kill special exception handler sections
avr32: Kill unneeded #include <asm/pgalloc.h> from asm/mmu_context.h
avr32: Clean up time.c #includes
...
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (71 commits)
[S390] sclp_tty: Fix scheduling while atomic bug.
[S390] sclp_tty: remove ioctl interface.
[S390] Remove P390 support.
[S390] Cleanup vmcp printk messages.
[S390] Cleanup lcs printk messages.
[S390] Cleanup kprobes printk messages.
[S390] Cleanup vmwatch printk messages.
[S390] Cleanup dcssblk printk messages.
[S390] Cleanup zfcp dumper printk messages.
[S390] Cleanup vmlogrdr printk messages.
[S390] Cleanup s390 debug feature print messages.
[S390] Cleanup monreader printk messages.
[S390] Cleanup appldata printk messages.
[S390] Cleanup smsgiucv printk messages.
[S390] Cleanup cpacf printk messages.
[S390] Cleanup qeth print messages.
[S390] Cleanup netiucv printk messages.
[S390] Cleanup iucv printk messages.
[S390] Cleanup sclp printk messages.
[S390] Cleanup zcrypt printk messages.
...
|
|
This simplifies the code significantly, and was the whole point of the
exercise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
arch/x86/kernel/entry_32.S
arch/x86/kernel/process_32.c
arch/x86/kernel/process_64.c
arch/x86/lib/Makefile
include/asm-x86/irqflags.h
kernel/Makefile
kernel/sched.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Remove the "uninitialized use" compile warning and avoid potential
runtime issue.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
There isn't any reason at this point that we can't build 82xx, 83xx & 86xx
support in with the other 6xx based boards. Twiddle the Kconfigs to allow
this.
This allows us to remove the machine type selection for related to 6xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Publish the devices listed in dts under SOC as of_device for 85xx_cds
platform. The devices are needed by the 85xx EDAC driver.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
For some reason long ago I decided that we should zero out the time base
when we calibrate the decrementer. The problem is that this can be
harmful in SMP systems where the firmware has already synchronized the
time bases on the various cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Moved the pic initialization into its own common file and out of the board
code. Also fixed the OF reference counting on the mpic node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
These issues were reported by Stephen Rothwell for another 85xx board
port and pointed out by Chen Gong as issues in the DS port.
* mpic OF node reference counting was off
* of_device_id struct should be marked as __initdata
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
udbg_putc is a *function pointer* that is initialized during
udbg_init_cpm. It might not be initialized properly when called from
udbg_putc_cpm(), so (recursively) call udbg_putc_cpm() directly.
Signed-off-by: Nye Liu <nyet@mrv.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix interrupt threading issue on pq2fads when running with CONFIG_PREEMPT_RT
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Most likely it is broken anyway because of the changes in memory
detection. Since we can't test it and there are probably better ways
that using a P390 card, remove support for it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Move memory detection code to own file and also simplify it.
Also add an interface which can be called at any time to get the
current memory layout. This interface is needed by our kernel
internal system dumper.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
As noted by Akinobu Mita in patch b1fceac2b9e04d278316b2faddf276015fc06e3b,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
arch/s390/kernel/topology.c | 2 --
1 file changed, 2 deletions(-)
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
