Age | Commit message (Collapse) | Author |
|
Add node describing Zynq's GPIO controller.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add node for the Xilinx A/D Converter.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
In Armada 375 SoCs, the MDIO is handled by a separate orion-mdio driver,
despite the register is contained within the "LMS" block of the network
controller.
Therefore we need to add the clock to the MDIO devicetree to prevent the
controller from being accesed with its clock gated. This is needed, for
instance, to be able to load the MDIO driver before the network driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1405961296-5846-7-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The vendor bootloader provided for Armada 375 boards expect an
alias for the ethernet nodes, which is used to fixup the MAC address.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lkml.kernel.org/r/1405961296-5846-6-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
ZONE_DMA is created to allow 32-bit only devices to access memory in the
absence of an IOMMU. On systems where the memory starts above 4GB, it is
expected that some devices have a DMA offset hardwired to be able to
access the bottom of the memory. Linux currently supports DT bindings
for the DMA offsets but they are not (easily) available early during
boot.
This patch tries to guess a DMA offset and assumes that ZONE_DMA
corresponds to the 32-bit mask above the start of DRAM.
Fixes: 2d5a5612bc (arm64: Limit the CMA buffer to 32-bit if ZONE_DMA)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
|
|
As clocksource pxa_timer was moved to clocksource framework, the
pxa_timer initialization needs to be a bit amended, to pass the
necessary informations to clocksource, ie :
- the timer interrupt (mach specific)
- the timer registers base (ditto)
- the timer clockrate
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Select CLKSRC_OF for PXA architectures.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Move time.c from arch/arm/mach-pxa/time.c to
drivers/clocksource/pxa_timer.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Adds ability to shutdown all CPUs except the first one
(since it might be special for a lot of platforms).
It is now possible to use kexec which requires such a feature.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When compiling for multiplatform for both ARMv6 and ARMv7, the default
compiler flags are for ARMv6, and the following cpu-hotplug change will
fail with:
/tmp/ccSFxfmI.s:68: Error: selected processor does not support ARM mode `isb '
/tmp/ccSFxfmI.s:74: Error: selected processor does not support ARM mode `isb '
/tmp/ccSFxfmI.s:75: Error: selected processor does not support ARM mode `dsb '
Fix this in a similar manner as in commit 9f0affcf3e21 "ARM: mvebu: Fix pmsu
compilation when ARMv6 is selected", by specifying ARMv7 flags for platsmp.o.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds bch8 ecc software fallback which is mostly used by
omap3s because they lack hardware elm support.
Fixes: 0611c41934ab35ce84dea34ab291897ad3cbc7be (ARM: OMAP2+: gpmc:
update gpmc_hwecc_bch_capable() for new platforms and ECC schemes)
Cc: <stable@vger.kernel.org> # 3.15.x+
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
A reference to ARCH_HAS_OPP was added in commit 333d17e56 (arm64: add
ARCH_HAS_OPP to allow enabling OPP library) however this symbol is no
longer needed after commit 049d595a4db3b3a (PM / OPP: Make OPP invisible
to users in Kconfig).
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
OMAP hwmod data additions for v3.17. Most of these are DRA7xx-related,
although one patch adds DSS hwmods for AM43xx.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-v3.17/20140722143514/
|
|
In the recent commit b50a6c584bb4 "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584bb4 ("powerpc/perf: Clear MMCR2 when enabling PMU")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
INV cmd for dcache provides 2 modes discard or wback-before-discard.
One is default and other needs to be set, if so desired. This is common
for line-op/entire-cache-op. So refactor them out into a helper
Doesn't affect generated code but paves way for any common
micro-optimization.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
* print aliasing or not, VIPT/PIPT etc
* compress param storage using bitfields
* more use of IS_ENABLED to de-uglify code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
With all IRQs unmasked by default on all cores, it is no longer needed
to unmask them explicitly.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Hardware keeps them enabled on reset, and Linux needs to keep status quo.
Any spurious interrupts will be reported/blocked by genirq.
This helps remove a SMP IRQ quirk (next commit), where a peripheral IRQ
is hard wired to core0, and request_irq()->unmask() happens on core1,
keeping the IRQ masked on core0, needing an explicit unmask.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The current cpu-private IRQ registration is ugly as it requires need to
expose arch_unmask_irq() outside of intc code.
So switch to percpu IRQ APIs:
-request_percpu_irq [boot core]
-enable_percpu_irq [all cores]
Encapsulated in helper arc_request_percpu_irq()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
59e79895b95892863617ce630fbda467f2470575
(ARM: shmobile: r8a7791: Add clocks)
added r8a7791 SD clocks when v3.14.
2c60a7df72711fb8b4be1e6aa651ab166a8931bc
(ARM: shmobile: Add SDHI devices for Koelsch DTS)
enabled SD on r8a7791 Koelsch when v3.15.
1299df03d7191ab4356c995dde8b912d3c8922e9
(ARM: shmobile: henninger: add SDHI0/2 DT support)
enable SD on r8a7791 Henninger when v3.16.
But r8a7791 SD clock had wrong address.
This patch fixup it.
[Kuninori Morimoto: tidyup for upstreaming]
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As exynos_cpuidle_init() and exynos_cpufreq_init() functions have just
one line of code for registering platform devices. So we can move them
to exynos_dt_machine_init() and remove exynos_cpuidle_init() and
exynos_cpufreq_init(). This will help in reducing lines of code in
exynos.c, making it more clean.
Suggested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Under "arm/mach-exynos" many files are using PMU register offsets.
Since we have added support for accessing PMU base address via DT,
now we can remove PMU mapping from exynosX_iodesc. Let's convert
all these access using iomapped address.
This will help us in removing static mapping of PMU base address
as well as help in reducing dependency over machine header files.
Thus helping for migration of PMU implementation from machine to
driver folder which can be reused for ARM64 based SoC.
Also as we have removed static mappings from "regs-pmu.h" it does
not need map.h anymore. But "platsmp.c" needed this and till now it
got included indirectly. So lets move header inclusion of
"mach/map.h" from "regs-pmu.h" to "platsmp.c".
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Turning off a cluster when all 4 cores of the cluster are powered off
saves power significantly. Powering off the A15 L2 alone gives around
100mW in savings. Add support for powering off the A15/A7 clusters on
exynos5420/5800.
The patch enables specific register bits which ensure that:
- cluster L2 will be turned on before the first man is powered up.
- last man will be turned off before the cluster L2 is turned off.
- core is powered down before powering it up.
Remove the exynos_cluster_power_control function completely as we can
rely on the above mentioned bits rather than polling the cluster power
status register.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
|
|
The forthcoming patch will make <acpi/acpi.h> to be visible to all kernel
source code. Thus for the architectures that do not support ACPI and
haven't implemented <asm/acenv.h>, we need to make it excluded.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
GHES currently maps two pages with atomic_ioremap. From now
on, NMI is architectural depended so there is no need to allocate
an NMI page for platforms without NMI support.
To make it possible to not use a second page, swap the existing
page order so that the IRQ context page is first, and the optional
NMI context page is second. Then, use HAVE_ACPI_APEI_NMI to decide
how many pages are to be allocated.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Currently APEI depends on x86 architecture. It is because of NMI hardware
error notification of GHES which is currently supported by x86 only.
However, many other APEI features can be still used perfectly by other
architectures.
This commit adds two symbols:
1. HAVE_ACPI_APEI for those archs which support APEI.
2. HAVE_ACPI_APEI_NMI which is used for NMI code isolation in ghes.c
file. NMI related data and functions are grouped so they can be wrapped
inside one #ifdef section. Appropriate function stubs are provided for
!NMI case.
Note there is no functional changes for x86 due to hard selected
HAVE_ACPI_APEI and HAVE_ACPI_APEI_NMI symbols.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This commit abstracts MCE calls and provides weak corresponding default
implementation for those architectures which do not need arch specific
actions. Each platform willing to do additional architectural actions
should provides desired function definition. It allows us to avoid wrap
code into #ifdef in generic code and prevent new platform from introducing
dummy stub function too.
Initially, there are two APEI arch-specific calls:
- arch_apei_enable_cmcff()
- arch_apei_report_mem_error()
Both interact with MCE driver for X86 architecture.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
Add hwmod data for RTC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Adding hwmod data for CPSW and MDIO which is present in DRA7xx SoC
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Added hwmod data for pcie1 and pcie2 subsystem present in DRA7xx SOC.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Added hwmod data for pcie1 and pcie2 phy present in DRA7xx SOC.
Also added the missing CLKCTRL OFFSET macro and CONTEXT OFFSET macro
for pcie1 phy and pcie2 phy.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This module is needed for the SATA and PCIe PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.stlinux.com/devel/kernel/linux-sti into next/defconfig
Merge "ARM: STi: defconfig changes for v3.17" from Maxime Coquelin:
STi defconfig updates for v3.17
- Enable ST's Thermal controller driver
- Enable ST's Keyscan driver
- Enable ST's MiPHY365 Phy driver for STiH416 SATA & PCIe
- Enable ST's AHCI driver.
* tag 'sti-defconfig-for-v3.17-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: multi_v7_defconfig: Enable MiPHY365x - ST's Generic (SATA & PCIe) PHY
ARM: multi_v7_defconfig: Enable ST's (S)ATA driver
ARM: multi_v7_defconfig: add ST Keyscan driver
ARM: update multi_v7_defconfig for STI
ARM: multi_v7_defconfig: Configure in ST's Thermal Controller
+ Linux 3.16-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Aquaris5 is a mobile phone based on the MT6589 SoC.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This adds a generic devicetree board file and a dtsi for boards
based on MT6589 SoCs from Mediatek.
Apart from the generic parts (gic, clocks) the only component
currently supported are the timers.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
This patch adds KEYBOARD_ST_KEYSCAN config
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
|
|
Commit 554086d ("x86_32, entry: Do syscall exit work on badsys
(CVE-2014-4508)") introduced a regression in the x86_32 syscall entry
code, resulting in syscall() not returning proper errors for undefined
syscalls on CPUs supporting the sysenter feature.
The following code:
> int result = syscall(666);
> printf("result=%d errno=%d error=%s\n", result, errno, strerror(errno));
results in:
> result=666 errno=0 error=Success
Obviously, the syscall return value is the called syscall number, but it
should have been an ENOSYS error. When run under ptrace it behaves
correctly, which makes it hard to debug in the wild:
> result=-1 errno=38 error=Function not implemented
The %eax register is the return value register. For debugging via ptrace
the syscall entry code stores the complete register context on the
stack. The badsys handlers only store the ENOSYS error code in the
ptrace register set and do not set %eax like a regular syscall handler
would. The old resume_userspace call chain contains code that clobbers
%eax and it restores %eax from the ptrace registers afterwards. The same
goes for the ptrace-enabled call chain. When ptrace is not used, the
syscall return value is the passed-in syscall number from the untouched
%eax register.
Use %eax as the return value register in syscall_badsys and
sysenter_badsys, like a real syscall handler does, and have the caller
push the value onto the stack for ptrace access.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.11.1407221022380.31021@titan.int.lan.stealer.net
Reviewed-and-tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: <stable@vger.kernel.org> # If 554086d is backported
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
Bugfixes
--------
- add IPTE to trace event decoder
- document and advertise KVM_CAP_S390_IRQCHIP
Cleanups
--------
- Reuse kvm_vcpu_block for s390
- Get rid of tasklet for wakup processing
|
|
This changes the default IOTLB flushing method to lazy flushing, which
means that there will be no direct flush after each DMA unmap operation.
Instead, the iommu bitmap pointer will be adjusted after unmap, so that
no DMA address will be re-used until after an iommu bitmap wrap-around.
The only IOTLB flush will then happen after each wrap-around.
A new kernel parameter "s390_iommu=" is also introduced, to allow changing
the flushing behaviour to the old strict method.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|