summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)Author
2011-08-05ARM: iMX5: Don't enable DPLL if it already enabledJason Liu
If the DPLL is already enabled, don't try to enable it again. Since write to the DPLL control register will make the DPLL reset and which will cause some issues when some child module are sourced from this DPLL. Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-08-01i.MX25 GPT clock fix: ensure correct the clock sourceMehnert, Torsten
Request for comment and commit. From: T. Mehnert <t.mehnert@eckelmann.de> Date: Mon, 4 Jul 2011 15:53:30 +0200 Subject: [PATCH] i.MX25 GPT clock fix: ensure correct the clock source This patch ensures, that Linux will take the correct clock source (AHB_DIV) for gpt in the ARM i.MX25 implementation. The currect code depends on the reset defaults of the CCM_MCR register. So on some boards it could happen that the UPLL is used for clock source, which results in faulty time behavior in Linux. In this case all delays or sleeps will will be faktor 1.8 too long. Signed-off-by: Torsten Mehnert <t.mehnert@eckelmann.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26ARM: board-mx51_babbage: Fix UART2 registrationFabio Estevam
On MX51 Babbage board the RTS/CTS pins are not used on UART2 port. Fix the registration of this port. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26efika: Fix board id detectionArnaud Patard (Rtp)
Current code is assuming that gpio_get_value() is returning 0 or 1 but it should be checking if the value is 0 or not. Not doing it properly is breaking the detection of the board (and thus the reboot of efika mx to2) when using the new mxc gpio driver, which relies on basic mmio gpio. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26efikasb: fix gpio keys.Arnaud Patard (Rtp)
While testing the keys, I only checked that the key were generating an input event but unfortunately, they were not generating the right event. Fix that. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26efikasb/mx: fix usbh1 initialisationArnaud Patard (Rtp)
mx51_initialize_usb_hw() support introduced a small error. The usbh1 has pdev->id equal to 1 not 0, so use pdev->id to make things less error-prone and to fix that. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26ARM: mx53: add pad configuration for I2C signalsEric Miao
I2C signals SDA/SCL are a bit different, they need to be pull-up and open-drain (so to support multiple I2C devices). Signed-off-by: Richard Zhao <richard.zhao@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26ARM: mach-imx/mx31lilly: Fix section mismatchesFabio Estevam
Fix the following section mismatches: WARNING: vmlinux.o(.text+0x1026c): Section mismatch in reference from the function lilly1131_usb_init() to the variable .init.rodata:imx31_mxc_ehci_hs_data The function lilly1131_usb_init() references the variable __initconst imx31_mxc_ehci_hs_data. This is often because lilly1131_usb_init lacks a __initconst annotation or the annotation of imx31_mxc_ehci_hs_data is wrong. WARNING: vmlinux.o(.text+0x10270): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.rodata:(unknown) The function lilly1131_usb_init() references the (unknown reference) __initconst (unknown). This is often because lilly1131_usb_init lacks a __initconst annotation or the annotation of (unknown) is wrong. WARNING: vmlinux.o(.text+0x10274): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.data:(unknown) The function lilly1131_usb_init() references the (unknown reference) __initdata (unknown). This is often because lilly1131_usb_init lacks a __initdata annotation or the annotation of (unknown) is wrong. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26ARM: mach-imx/mx31ads: Fix section mismatchesFabio Estevam
Fix the following section mismatches: WARNING: vmlinux.o(.text+0x101cc): Section mismatch in reference from the function mxc_init_i2c() to the (unknown reference) .init.data:(unknown) The function mxc_init_i2c() references the (unknown reference) __initdata (unknown). This is often because mxc_init_i2c lacks a __initdata annotation or the annotation of (unknown) is wrong. WARNING: vmlinux.o(.text+0x101d8): Section mismatch in reference from the function mxc_init_i2c() to the variable .init.rodata:imx31_imx_i2c_data The function mxc_init_i2c() references the variable __initconst imx31_imx_i2c_data. This is often because mxc_init_i2c lacks a __initconst annotation or the annotation of imx31_imx_i2c_data is wrong. WARNING: vmlinux.o(.text+0x10200): Section mismatch in reference from the function mxc_init_audio() to the variable .init.rodata:imx31_imx_ssi_data The function mxc_init_audio() references the variable __initconst imx31_imx_ssi_data. This is often because mxc_init_audio lacks a __initconst annotation or the annotation of imx31_imx_ssi_data is wrong. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-26Add tlv320aic32x4 platform data to Visstrim_M10.Javier Martin
Without this platform data the aic32x4 audio codec in the Visstrim_M10 won't work properly. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-21Merge branch 'for_linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: sparc,kgdbts: fix compile regression with kgdb test suite
2011-07-21sparc,kgdbts: fix compile regression with kgdb test suiteJason Wessel
Commit 63ab25ebbc (kgdbts: unify/generalize gdb breakpoint adjustment) introduced a compile regression on sparc. kgdbts.c: In function 'check_and_rewind_pc': kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set' Simply add the correct macro definition for instruction pointer on the Sparc architecture. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: David S. Miller <davem@davemloft.net>
2011-07-21x86: Make Dell Latitude E6420 use reboot=pciH. Peter Anvin
Yet another variant of the Dell Latitude series which requires reboot=pci. From the E5420 bug report by Daniel J Blueman: > The E6420 is affected also (same platform, different casing and > features), which provides an external confirmation of the issue; I can > submit a patch for that later or include it if you prefer: > http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/ Reported-by: Daniel J Blueman <daniel.blueman@gmail.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
2011-07-21x86: Make Dell Latitude E5420 use reboot=pciDaniel J Blueman
Rebooting on the Dell E5420 often hangs with the keyboard or ACPI methods, but is reliable via the PCI method. [ hpa: this was deferred because we believed for a long time that the recent reshuffling of the boot priorities in commit 660e34cebf0a11d54f2d5dd8838607452355f321 fixed this platform. Unfortunately that turned out to be incorrect. ] Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.com Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
2011-07-20Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86. reboot: Make Dell Latitude E6320 use reboot=pci x86, doc only: Correct real-mode kernel header offset for init_size x86: Disable AMD_NUMA for 32bit for now
2011-07-19Merge branch 'fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: davinci: DM365 EVM: fix video input mux bits ARM: davinci: Check for NULL return from irq_alloc_generic_chip arm: davinci: Fix low level gpio irq handlers' argument
2011-07-19davinci: DM365 EVM: fix video input mux bitsJon Povey
Video input mux settings for tvp7002 and imager inputs were swapped. Comment was correct. Tested on EVM with tvp7002 input. Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> Acked-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: stable@kernel.org Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-19ARM: davinci: Check for NULL return from irq_alloc_generic_chipTodd Poynor
Avoid NULL dereference of irq_alloc_generic_chip return in low memory conditions. Signed-off-by: Todd Poynor <toddpoynor@google.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-17Merge branch 'pm-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6 * 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: PM / MIPS: Convert i8259.c to using syscore_ops
2011-07-17Merge branch 's5p-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung * 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: SAMSUNG: DMA Cleanup as per sparse ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chip
2011-07-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc: sun4m SMP: fix wrong shift instruction in IPI handler sparc32,leon: Added __init declaration to leon_flush_needed() sparc/irqs: Do not trace arch_local_{*,irq_*} functions
2011-07-16sparc: sun4m SMP: fix wrong shift instruction in IPI handlerWill Simoneau
This shift instruction appears to be shifting in the wrong direction. Without this change, my SparcStation-20MP hangs just after bringing up the second CPU: Entering SMP Mode... Starting CPU 2 at f02b4e90 Brought up 2 CPUs Total of 2 processors activated (99.52 BogoMIPS). *** stuck *** Signed-off-by: Will Simoneau <simoneau@ele.uri.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-16ARM: SAMSUNG: DMA Cleanup as per sparseSangwook Lee
Function declaration differs between file: dma.c and file:dma.h and SPARSE (Documentation/sparse.txt) gives error messages All dma channels are members of 'enum dma_ch' and not 'unsigned int' Please have a look at channel definitions in: arch/arm/mach-s3c64xx/include/mach/dma.h arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h arch/arm/mach-s3c2410/include/mach/dma.h So all arguments should be of type 'enum dma_ch' Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-07-16ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chipTodd Poynor
Signed-off-by: Todd Poynor <toddpoynor@google.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-07-15ARM: fix regression in IXP4xx clocksourceRichard Cochran
Commit 234b6ceddb4fc2a4bc5b9a7670f070f6e69e0868 clocksource: convert ARM 32-bit up counting clocksources broke the build for ixp4xx and made big endian operation impossible. This commit restores the original behaviour. Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> [ Thomas says that we might want to have generic BE accessor functions to the MMIO clock source, but that hasn't happened yet, so in the meantime this seems to be the short-term fix for the particular problem - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-16PM / MIPS: Convert i8259.c to using syscore_opsRafael J. Wysocki
The code in arch/mips/kernel/i8259.c still hasn't been converted to using struct syscore_ops instead of a sysdev for resume and shutdown. As a result, this code doesn't build any more after suspend, resume and shutdown callbacks have been removed from struct sysdev_class. Fix this problem by converting i8259.c to using syscore_ops. Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Ralf Baechle <ralf@linux-mips.org>
2011-07-12x86. reboot: Make Dell Latitude E6320 use reboot=pciMaxime Ripard
The Dell Latitude E6320 doesn't reboot unless reboot=pci is set. Force it thanks to DMI. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Link: http://lkml.kernel.org/r/1309269451-4966-1-git-send-email-maxime.ripard@free-electrons.com Cc: Matthew Garrett <mjg@redhat.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
2011-07-12Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/mm: Fix memory_block_size_bytes() for non-pseries mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
2011-07-12Merge branch 'fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting ARM: pxa/raumfeld: fix device name for codec ak4104 ARM: pxa/raumfeld: display initialisation fixes ARM: pxa/raumfeld: adapt to upcoming hardware change ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd) arm: mach-vt8500: add forgotten irq_data conversion ARM: pxa168: correct nand pmu setting ARM: pxa910: correct nand pmu setting ARM: pxa: fix PGSR register address calculation
2011-07-12arm: davinci: Fix low level gpio irq handlers' argumentIdo Yariv
Commit 7416401 ("arm: davinci: Fix fallout from generic irq chip conversion") introduced a bug, causing low level interrupt handlers to get a bogus irq number as an argument. The gpio irq handler falsely assumes that the handler data is the irq base number and that is no longer true. Set the irq handler data to be a pointer to the corresponding gpio controller. The chained irq handler can then use it to extract both the irq base number and the gpio registers structure. Signed-off-by: Ido Yariv <ido@wizery.com> CC: Thomas Gleixner <tglx@linutronix.de> [nsekhar@ti.com: renamed "ctl" to "d", simplified indexing logic for chips and took care of odd bank handling in irq handler] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2011-07-12powerpc/mm: Fix memory_block_size_bytes() for non-pseriesBenjamin Herrenschmidt
Just compiling pseries in the kernel causes it to override memory_block_size_bytes() regardless of what is the runtime platform. This cleans up the implementation of that function, fixing a bug or two while at it, so that it's harmless (and potentially useful) for other platforms. Without this, bugs in that code would trigger a WARN_ON() in drivers/base/memory.c when booting some different platforms. If/when we have another platform supporting memory hotplug we might want to either move that out to a generic place or make it a ppc_md. callback. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-07-12mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a headerBenjamin Herrenschmidt
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c files, and I need it in a third one to fix a powerpc bug, so let's first move it into a header Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Ingo Molnar <mingo@elte.hu>
2011-07-11Merge branch 'fix' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
2011-07-11x86: Disable AMD_NUMA for 32bit for nowTejun Heo
Commit 2706a0bf7b ("x86, NUMA: Enable CONFIG_AMD_NUMA on 32bit too") enabled AMD NUMA for 32bit too. Unfortunately, SPARSEMEM on 32bit had rather coarse (512MiB) addr->node mapping granularity due to lack of space in page->flags. This led to boot failure on certain AMD NUMA machines which had 128MiB alignment on nodes. Patches to properly detect this condition and reject NUMA configuration are posted[1] but deemed too pervasive for merge at this point (-rc6). Disable AMD NUMA for 32bit for now and re-enable once the detection logic is merged. [1] http://thread.gmane.org/gmane.linux.kernel/1161279/focus=1162583 Reported-by: Hans Rosenfeld <hans.rosenfeld@amd.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Conny Seidel <conny.seidel@amd.com> Link: http://lkml.kernel.org/r/20110711083432.GC943@htj.dyndns.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
2011-07-11ARM: pxa/raumfeld: fix device name for codec ak4104Daniel Mack
In commit f0fba2ad (ASoC: multi-component - ASoC Multi-Component Support), the name of the ak4104 codec driver was changed without amending the platform code which uses it as well. Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-07-11ARM: pxa/raumfeld: display initialisation fixesSven Neumann
The display requires some milliseconds between GPIO_TFT_VA_EN and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with the display spec. Also tune timings for better compliance with the spec. Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Acked-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-07-11ARM: pxa/raumfeld: adapt to upcoming hardware changeSven Neumann
The backlight control is going to change back to PWM in the upcoming Raumfeld Controller hardware revision. Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Acked-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-07-11ARM: pxa: fix gpio_to_chip() clash with gpiolib namespaceLinus Walleij
The PXA platform code has a static inline helper called gpio_to_chip which clashes with the gpiolib namespace if we try to expose the function with the same name from gpiolib, and it's still confusing even if we don't do that. So rename it to gpio_to_pxachip(). Reported-by: H Hartley Sweeten <hartleys@visionengravers.com> Cc: Eric Miao <eric.miao@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2011-07-10Merge branch 'fixes' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing ARM: 6987/1: l2x0: fix disabling function to avoid deadlock ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1 ARM: 6980/1: mmci: use StartBitErr to detect bad connections ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion ARM: move memory layout sanity checking before meminfo initialization ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging ARM: 6989/1: perf: do not start the PMU when no events are present ARM: dmabounce: fix map_single() error return value
2011-07-08Merge branch 's5p-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung * 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: S3C2440: fix section mismatch on mini2440 ARM: S3C24XX: drop return codes in void function of dma.c ARM: S3C24XX: don't use uninitialized variable in dma.c ARM: EXYNOS4: Set appropriate I2C device variant ARM: S5PC100: Fix for compilation error spi/s3c64xx: Bug fix for SPI with different FIFO level ARM: SAMSUNG: Add tx_st_done variable ARM: EXYNOS4: Address a section mismatch w/ suspend issue. ARM: S5P: Fix bug on init of PWMTimers for HRTimer ARM: SAMSUNG: header file revised to prevent declaring duplicated ARM: EXYNOS4: fix improper gpio configuration ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
2011-07-08Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: omap: drop __initdata tags from static struct platform_device declarations
2011-07-08ARM: S3C2440: fix section mismatch on mini2440Wolfram Sang
If mini2440_init() is in __init, mini2440_parse_features() should also be in __init. Fixes: (.text+0x9adc): Section mismatch in reference from the function mini2440_parse_features.clone.0() to the (unknown reference) .init.data:(unknown) The function mini2440_parse_features.clone.0() references the (unknown reference) __initdata (unknown). Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Michel Pollet <buserror@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-07-08ARM: S3C24XX: drop return codes in void function of dma.cWolfram Sang
Commit bb072c3c (ARM / Samsung: Use struct syscore_ops for "core" power management) turned s3c2410_dma_resume_chan() from int to void. So, drop the actual return values, too. Fixes: arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_resume_chan': arch/arm/plat-s3c24xx/dma.c:1238:3: warning: 'return' with a value, in function returning void arch/arm/plat-s3c24xx/dma.c:1250:2: warning: 'return' with a value, in function returning void Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-07-08ARM: S3C24XX: don't use uninitialized variable in dma.cWolfram Sang
Commit 8970ef47 (S3C24XX: Remove hardware specific registers from DMA calls) removed the parameter dcon in s3c2410_dma_config() and calculates it on its own. So the debug-output for the old parameter can go, too. Fixes: arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_config': arch/arm/plat-s3c24xx/dma.c:1030:2: warning: 'dcon' is used uninitialized in this function Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-07-07Merge branch 'stable/bug.fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen * 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/pci: Move check for acpi_sci_override_gsi to xen_setup_acpi_sci.
2011-07-07Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: Don't use the EFI reboot method by default x86, suspend: Restore MISC_ENABLE MSR in realmode wakeup x86, reboot: Acer Aspire One A110 reboot quirk x86-32, NUMA: Fix boot regression caused by NUMA init unification on highmem machines
2011-07-07Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and ↵Linus Torvalds
'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: debugobjects: Fix boot crash when kmemleak and debugobjects enabled * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: jump_label: Fix jump_label update for modules oprofile, x86: Fix race in nmi handler while starting counters * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: Disable (revert) SCHED_LOAD_SCALE increase sched, cgroups: Fix MIN_SHARES on 64-bit boxen
2011-07-07xen/pci: Move check for acpi_sci_override_gsi to xen_setup_acpi_sci.Konrad Rzeszutek Wilk
Previously we would check for acpi_sci_override_gsi == gsi every time a PCI device was enabled. That works during early bootup, but later on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup. The reason is that acpi_sci_override_gsi was declared in __initdata and after early bootup could contain bogus values. This patch moves the check for acpi_sci_override_gsi to the site where the ACPI SCI is preset. CC: stable@kernel.org Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net> Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net> [http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html] Suggested-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2011-07-07genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)Simon Guinot
This fixes a regression introduced by e59347a "arm: orion: Use generic irq chip". Depending on the device, interrupts acknowledgement is done by setting or by clearing a dedicated register. Replace irq_gc_ack() with some {set,clr}_bit variants allows to handle both cases. Note that this patch affects the following SoCs: Davinci, Samsung and Orion. Except for this last, the change is minor: irq_gc_ack() is just renamed into irq_gc_ack_set_bit(). For the Orion SoCs, the edge GPIO interrupts support is currently broken. irq_gc_ack() try to acknowledge a such interrupt by setting the corresponding cause register bit. The Orion GPIO device expect the opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used. Tested on Network Space v2. Reported-by: Joey Oravec <joravec@drewtech.com> Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-07-07arm: mach-vt8500: add forgotten irq_data conversionWolfram Sang
This platform has not been converted to 'struct irq_data' when the big pile was done. It fails to compile nowadays, because the compatibility code has gone. CC arch/arm/mach-vt8500/irq.o arch/arm/mach-vt8500/irq.c:118:2: error: unknown field 'ack' specified in initializer arch/arm/mach-vt8500/irq.c:118:2: warning: initialization from incompatible pointer type arch/arm/mach-vt8500/irq.c:119:2: error: unknown field 'mask' specified in initializer arch/arm/mach-vt8500/irq.c:119:2: warning: initialization from incompatible pointer type arch/arm/mach-vt8500/irq.c:120:2: error: unknown field 'unmask' specified in initializer arch/arm/mach-vt8500/irq.c:120:2: warning: initialization from incompatible pointer type arch/arm/mach-vt8500/irq.c:121:2: error: unknown field 'set_type' specified in initializer arch/arm/mach-vt8500/irq.c:121:2: warning: initialization from incompatible pointer type make[1]: *** [arch/arm/mach-vt8500/irq.o] Error 1 Add the missing conversion. Tested on a JayPC-Tablet. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Alexey Charkov <alchark@gmail.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>