| Age | Commit message (Collapse) | Author |
|---|
|
The naming convention of this driver was always under the scanner, people
complained that it should have a more generic name than cpu0, as it manages all
CPUs that are sharing clock lines.
Also, in future it will be modified to support any number of clusters with
separate clock/voltage lines.
Lets rename it to 'cpufreq_dt' from 'cpufreq_cpu0'.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Size restrictions native kernels wouldn't have resulted from the initrd
getting mapped into the initial mapping. The kernel doesn't really need
the initrd to be mapped, so use infrastructure available in Xen to avoid
the mapping and hence the restriction.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
The Xen ARM API is stable since Xen 4.4 and everything has been
upstreamed in Linux for ARM and ARM64. Therefore we can drop "EXPERIMENTAL"
from the Xen option in the both Kconfig.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
|
|
No functional changes
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
hwreg_present() and hwreg_write() temporarily change the VBR register to
another vector table. This table contains a valid bus error handler
only, all other entries point to arbitrary addresses.
If an interrupt comes in while the temporary table is active, the
processor will start executing at such an arbitrary address, and the
kernel will crash.
While most callers run early, before interrupts are enabled, or
explicitly disable interrupts, Finn Thain pointed out that macsonic has
one callsite that doesn't, causing intermittent boot crashes.
There's another unsafe callsite in hilkbd.
Fix this for good by disabling and restoring interrupts inside
hwreg_present() and hwreg_write().
Explicitly disabling interrupts can be removed from the callsites later.
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
|
|
It pulls in more code, including causing us to build a relocatable
kernel, which is good for testing.
The resulting kernel is still usable as a non-crash dump kernel.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
For __ioremap().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Because powernv arrived after these other platforms, the defconfigs
didn't have PPC_POWERNV disabled, and being default y it gets turned on.
If we're going to bother having defconfigs for the specific platforms
then they should only build the code required for those platforms.
The grab bag of everything config is ppc64_defconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pci_bus_find_capability() is decleared in pci.h, so it is not necessary to do
it again.
This patch removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
rtas_call() accepts and returns values in CPU endianness.
The ddw_query_response and ddw_create_response structs members are
defined and treated as BE but as they are passed to rtas_call() as
(u32 *) and they get byteswapped automatically, the data is CPU-endian.
This fixes ddw_query_response and ddw_create_response definitions and use.
of_read_number() is designed to work with device tree cells - it assumes
the input is big-endian and returns data in CPU-endian. However due
to the ddw_create_response struct fix, create.addr_hi/lo are already
CPU-endian so do not byteswap them.
ddw_avail is a pointer to the "ibm,ddw-applicable" property which contains
3 cells which are big-endian as it is a device tree. rtas_call() accepts
a RTAS token in CPU-endian. This makes use of of_property_read_u32_array
to byte swap and avoid the need for a number of be32_to_cpu calls.
Cc: stable@vger.kernel.org # v3.13+
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[aik: folded Anton's patch with of_property_read_u32_array]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use the much more reader friendly ACCESS_ONCE() instead of the cast to volatile.
This is purely a stylistic change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1411482607-20948-1-git-send-email-bobby.prani@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
environment
PMU checking can fail due to various reasons. On native machine, this
is mostly caused by faulty hardware and it is reasonable to use
KERN_ERR in reporting. However, when kernel is running on virtualized
environment, this checking can fail if virtual PMU is not supported
(e.g. KVM on AMD host). It is annoying to see an error message on
splash screen, even though we know such failure is benign on
virtualized environment.
This patch checks if the kernel is running in a virtualized environment.
If so, it will use KERN_INFO in reporting, which reduces the syslog
priority of them. This patch was tested successfully on KVM.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1411617314-24659-1-git-send-email-wei@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I was looking for the trinity oops cause in the uncore driver.
(so far didn't found it)
However I found this tiny race: when a box is set up two threads on the
same CPU, they may be setting up the box in parallel (e.g. with kernel
preemption). This could lead to the reference count being increasing
too much. Always recheck there is no existing cpu reference inside the lock.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1411424826-15629-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On 32 bit systems cmpxchg cannot handle 64 bit values, so
some additional magic is required to allow a 32 bit system
with CONFIG_VIRT_CPU_ACCOUNTING_GEN=y enabled to build.
Make sure the correct cmpxchg function is used when doing
an atomic swap of a cputime_t.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Cc: oleg@redhat.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux390@de.ibm.com
Cc: linux-arch@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20140930155947.070cdb1f@annuminas.surriel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
cebf15eb09a2 ("x86, sched: Add new topology for multi-NUMA-node CPUs")
some code to try to detect the situation where we have a NUMA node
inside of the "DIE" sched domain.
It detected this by looking for cpus which match_die() but do not match
NUMA nodes via topology_same_node().
I wrote it up as:
if (match_die(c, o) == !topology_same_node(c, o))
which actually seemed to work some of the time, albiet
accidentally.
It should have been doing an &&, not an ==.
This code essentially chopped off the "DIE" domain on one of
Andrew Morton's systems. He reported that this patch fixed his
issue.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Link: http://lkml.kernel.org/r/20140930214546.FD481CFF@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
into for-next
|
|
This patch extends the start and end address of initrd to be page aligned,
so that we can free all memory including the un-page aligned head or tail
page of initrd, if the start or end address of initrd are not page
aligned, the page can't be freed by free_initrd_mem() function.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch changes the __init_end address to a
page align address, so that free_initmem() can
free the whole .init section, because if the end
address is not page aligned, it will round down to
a page align address, then the tail unligned page
will not be freed.
Signed-off-by: wang <yalin.wang2010@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Carlo Caione <carlo@caione.org>
|
|
When both 'cache-size' and 'cache-sets' are specified for a L2 cache
controller node, parse those properties and set up the
set size based on which type of L2 cache controller we are using.
Update the L2 cache controller Device Tree binding with the optional
'cache-size', 'cache-sets', 'cache-block-size' and 'cache-line-size'
properties. These come from the ePAPR specification.
Using the cache size, number of sets and cache line size we can
calculate desired associativity of the L2 cache. This is done
by the calculation:
set size = cache size / sets
ways = set size / line size
way size = cache size / ways = sets * line size
associativity = cache size / way size
Example output from the PB1176 DT that look like this:
L2: l2-cache {
compatible = "arm,l220-cache";
(...)
arm,override-auxreg;
cache-size = <131072>; // 128kB
cache-sets = <512>;
cache-line-size = <32>;
};
Ends up like this:
L2C OF: override cache size: 131072 bytes (128KB)
L2C OF: override line size: 32 bytes
L2C OF: override way size: 16384 bytes (16KB)
L2C OF: override associativity: 8
L2C: DT/platform modifies aux control register: 0x02020fff -> 0x02030fff
L2C-220 cache controller enabled, 8 ways, 128 kB
L2C-220: CACHE_ID 0x41000486, AUX_CTRL 0x06030fff
Which is consistent with the value earlier hardcoded for the
PB1176 platform.
This patch is an extended version based on the initial patch
by Florian Fainelli.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds support for clock_gettime with CLOCK_REALTIME
and CLOCK_MONOTONIC using vDSO. It also updates the vdso
struct nomenclature used for the clocks to match the x86 code
to keep it easier to update going forward.
We also support the *_COARSE clockid_t, for apps that want speed
but aren't concerned about fine-grained timestamps; this saves
about 20 cycles per call (see http://lwn.net/Articles/342018/).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: John Stultz <john.stultz@linaro.org>
|
|
This fixes the following OOPS:
loaded kvm module (v3.17-rc1-168-gcec26bc)
BUG: unable to handle kernel paging request at fffffffffffffffe
IP: [<ffffffff81168449>] put_page+0x9/0x30
PGD 1e15067 PUD 1e17067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
[<ffffffffa063271d>] ? kvm_vcpu_reload_apic_access_page+0x5d/0x70 [kvm]
[<ffffffffa013b6db>] vmx_vcpu_reset+0x21b/0x470 [kvm_intel]
[<ffffffffa0658816>] ? kvm_pmu_reset+0x76/0xb0 [kvm]
[<ffffffffa064032a>] kvm_vcpu_reset+0x15a/0x1b0 [kvm]
[<ffffffffa06403ac>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
[<ffffffffa062e540>] kvm_vm_ioctl+0x200/0x780 [kvm]
[<ffffffff81212170>] do_vfs_ioctl+0x2d0/0x4b0
[<ffffffff8108bd99>] ? __mmdrop+0x69/0xb0
[<ffffffff812123d1>] SyS_ioctl+0x81/0xa0
[<ffffffff8112a6f6>] ? __audit_syscall_exit+0x1f6/0x2a0
[<ffffffff817229e9>] system_call_fastpath+0x16/0x1b
Code: c6 78 ce a3 81 4c 89 e7 e8 d9 80 ff ff 0f 0b 4c 89 e7 e8 8f f6 ff ff e9 fa fe ff ff 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 <48> f7 07 00 c0 00 00 55 48 89 e5 75 1e 8b 47 1c 85 c0 74 27 f0
RIP [<ffffffff81193045>] put_page+0x5/0x50
when not using the in-kernel irqchip ("-machine kernel_irqchip=off"
with QEMU). The fix is to make the same check in
kvm_vcpu_reload_apic_access_page that we already have
in vmx.c's vm_need_virtualize_apic_accesses().
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 4256f43f9fab91e1c17b5846a240cf4b66a768a8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change the type of physical address from unsigned long to phys_addr_t,
make valid_phys_addr_range more readable.
Signed-off-by: Min-Hua Chen <orca.chen@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch enables Thunder SoCs in the arm64 defconfig. This is
esp. useful to add Thunder platforms to automated builds based on
arm64 defconfig.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This introduces ARCH_THUNDER to enable soc specific drivers and dtb
files.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add initial device tree nodes for Cavium Thunder SoCs with support of
48 cores and gicv3. The dtsi file requires further changes, esp. for
pci, gicv3-its and smmu. This changes will be added later together
with the device drivers.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull "mvebu DT changes for v3.18 (round 2)" from Jason Cooper:
- Armada XP
- Add HW datasheet references to docs
- Armada 370
- Change internal registers to 0xf1000000 for Armada 370 RD board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'mvebu-dt-3.18-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: switch the Armada 370 RD board to internal registers at 0xf1000000
Documentation: arm: add hardware datasheet reference for Marvell Armada XP
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "Few keystone DTS fixes for 3.18" from Santosh Shilimkar:
- IO range fix for USB phy device
- Add missing dma-coherent property for K2E USB node
- Fix K2L MDIO start address
- Fix K2E MDIO start address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
|
|
hisi has a general dependency on ARCH_MULTIPLATFORM, which is
problematic when building a kernel for non-V7 platforms but selecting
drivers that might conflict with other architecture levels.
In this case, it broke my (still out of tree) patch set that
enables V7M multiplatform support, since that does not enable
MULTI_IRQ support:
arch/arm/kernel/built-in.o: In function `set_handle_irq':
arch/arm/kernel/irq.c:125: undefined reference to `handle_arch_irq'
arch/arm/kernel/built-in.o: In function `setup_arch':
arch/arm/kernel/setup.c:965: undefined reference to `handle_arch_irq'
Since all hisilicon platforms are ARMv7 based, we can avoid this
problem by just making the dependency more specific.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
|
|
UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Both strncpy and strlcpy suffer from the fact that they do
partial copies of strings into the destination when the target
buffer is too small. This is frequently pointless since an
overflow of the target buffer may make the result invalid.
strncpy() makes it relatively hard to even detect the error
condition, and with strlcpy() you have to duplicate the buffer
size parameter to test to see if the result exceeds it.
By returning zero in the failure case, we both make testing
for it easy, and by simply not copying anything in that case,
we make it mandatory for callers to test the error code.
To catch lazy programmers who don't check, we also place a NUL at
the start of the destination buffer (if there is space) to
ensure that the result is an invalid string.
At some point it may make sense to promote strscpy() to
a global platform-independent function, but other than the
reviewers, no one was interested on LKML, so for now leave
the strscpy() function as file-static.
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Use standard __init_begin and __init_end instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
ARRAY_SIZE is more concise to use when the size of an array is divided
by the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
// <smpl>
@i@
@@
@@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The definition of "comma" exists in scripts/Kbuild.include.
We should not double it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Clearing obj-y, obj-m, obj-n, obj- in each Makefile is
a useless habit.
They are non-exported variables; therefore they are always empty
whenever descending into each subdirectory.
(Moreorver, obj-y and obj-m are also set to empty at the beginning
of scripts/Makefile.build)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
In these Makefiles, at least one of "obj-y" and "obj-" is non-empty,
hence built-in.o is always created without such a trick.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au> [shmobile]
Acked-by: David S. Miller <davem@davemloft.net> [networking]
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
This patch replaces the static assignment of ~0 to dma_handle with
DMA_ERROR_CODE to be consistent with other platforms.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add printk levels to some places in the powerpc port.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add printk levels to powernv platform code, and convert to
pr_err() etc while here.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There is no need for yet another copy of the command line, just
use boot_command_line like everyone else.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use pr_fmt to give some context to the error messages in the
module code, and convert open coded debug printk to pr_debug.
Use pr_err for error messages.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Fill in the si_addr_lsb siginfo field so the hwpoison code can
pass to userspace the length of memory that has been corrupted.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
do_page_fault was missing knowledge of HWPOISON, and we would oops
if userspace tried to access a poisoned page:
kernel BUG at arch/powerpc/mm/fault.c:180!
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Exit out early for a kernel fault, avoiding indenting of
most of the function.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This reverts commit 7da4b29d496b1389d3a29b55d3668efecaa08ebd.
Now, that the issue is fixed, we can re-enable the code.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Merging the crypto tree for 3.17 to pull in the "by8" AVX CTR revert.
|
