| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two final fixlets for 3.18:
- Prevent microcode reload wreckage on 32bit
- Unbreak cross compilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Limit the microcode reloading to 64-bit for now
x86: Use $(OBJDUMP) instead of plain objdump
|
|
This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset. Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.
Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Many of AM335x and AM437x hook backlight to
one of these two devices. By enabling their
drivers we make sure pwm-backlight can do
its thing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AM437x devices have a DWC3 IP inside of them.
The host side implementation of DWC3 is XHCI
compliant. By enabling XHCI driver, we get
the USB host port on AM437x Starter Kit working
out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Without this, sound on AM437x Starter Kit will
not work.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AM437x Starter Kit ships with EDT FT5306 touchscreen
device. By enabling the driver we make sure touchscreen
will work out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
None of these drivers are known to be used on
any platform supported by omap2plus_defconfig,
by removing them we get a slight smaller kernel.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
|
|
SA-1111 uses internal MMIO space offsets as a device name, so device
name for sa1111 pcmcia is 1800 (PCMCIA is at offset 0x1800).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Both SA1100 framebuffer and PCMCIA drivers require knowledge of cpu
frequency to correctly program timings. Currently they receive timing
information by calling cpufreq_get(0). However if cpu frequency driver
is not enabled (e.g. due to unsupported DRAM chip/board on sa1110)
cpufreq_get(0) returns 0, causing incorrect timings to be programmed.
Add cpu clock returning cpu frequency, to be used by sa11x0 fb and
pcmcia drivers.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We reused host EBX and ECX, but KVM might not support all features;
emulated XSAVE size should be smaller.
EBX depends on unknown XCR0, so we default to ECX.
SDM CPUID (EAX = 0DH, ECX = 0):
EBX Bits 31-00: Maximum size (bytes, from the beginning of the
XSAVE/XRSTOR save area) required by enabled features in XCR0. May
be different than ECX if some features at the end of the XSAVE save
area are not enabled.
ECX Bit 31-00: Maximum size (bytes, from the beginning of the
XSAVE/XRSTOR save area) of the XSAVE/XRSTOR save area required by
all supported features in the processor, i.e all the valid bit
fields in XCR0.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add nested virtualization support for xsaves.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add logic to get/set the XSS model-specific register.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Initialize the XSS exit bitmap. It is zero so there should be no XSAVES
or XRSTORS exits.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
- EAX=0Dh, ECX=1: output registers EBX/ECX/EDX are reserved.
- EAX=0Dh, ECX>1: output register ECX bit 0 is clear for all the CPUID
leaves we support, because variable "supported" comes from XCR0 and not
XSS. Bits above 0 are reserved, so ECX is overall zero. Output register
EDX is reserved.
Source: Intel Architecture Instruction Set Extensions Programming
Reference, ref. number 319433-022
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This is the size of the XSAVES area. This starts providing guest support
for XSAVES (with no support yet for supervisor states, i.e. XSS == 0
always in guests for now).
Wanpeng Li suggested testing XSAVEC as well as XSAVES, since in practice
no real processor exists that only has one of them, and there is no
other way for userspace programs to compute the area of the XSAVEC
save area. CPUID(EAX=0xd,ECX=1).EBX provides an upper bound.
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Expose the XSAVES feature to the guest if the kvm_x86_ops say it is
available.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
For code that deals with cpuid, this makes things a bit more readable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Userspace is expecting non-compacted format for KVM_GET_XSAVE, but
struct xsave_struct might be using the compacted format. Convert
in order to preserve userspace ABI.
Likewise, userspace is passing non-compacted format for KVM_SET_XSAVE
but the kernel will pass it to XRSTORS, and we need to convert back.
Fixes: f31a9f7c71691569359fa7fb8b0acaa44bce0324
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
get_xsave_addr is the API to access XSAVE states, and KVM would
like to use it. Export it.
Cc: stable@vger.kernel.org
Cc: x86@kernel.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixups for kvm/next (3.19)
Here we have two fixups of the latest interrupt rework and
one architectural fixup.
|
|
The commit 3690951fc6d42f3a0903987677d0e592c49dd8db
(arm64: Use swiotlb late initialisation)
switches the DMA mapping code to swiotlb_tlb_late_init_with_default_size(),
the arm64_swiotlb_init() will not used anymore, so remove this function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.
This reverts commit b77d43943ea83997c6c37b8831d1561981d499c5.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
These are a pre-req to get rk3288 SMP to work with some firmwares, so merge
it in here as well as in next/drivers.
* clocksource/physical-timers:
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
|
|
* clocksource/physical-timers:
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
|
|
This is a bug fix for using physical arch timers when
the arch_timer_use_virtual boolean is false. It restores the
arch_counter_get_cntpct() function after removal in
0d651e4e "clocksource: arch_timer: use virtual counters"
We need this on certain ARMv7 systems which are architected like this:
* The firmware doesn't know and doesn't care about hypervisor mode and
we don't want to add the complexity of hypervisor there.
* The firmware isn't involved in SMP bringup or resume.
* The ARCH timer come up with an uninitialized offset between the
virtual and physical counters. Each core gets a different random
offset.
* The device boots in "Secure SVC" mode.
* Nothing has touched the reset value of CNTHCTL.PL1PCEN or
CNTHCTL.PL1PCTEN (both default to 1 at reset)
One example of such as system is RK3288 where it is much simpler to
use the physical counter since there's nobody managing the offset and
each time a core goes down and comes back up it will get reinitialized
to some other random value.
Fixes: 0d651e4e65e9 ("clocksource: arch_timer: use virtual counters")
Cc: stable@vger.kernel.org
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The imx6 PM code seems to be quite creative in its use of irq_data,
using something that is very much a hardware interrupt number where
we expect a virtual one. Yes, it worked so far, but that's only
luck, and it will definitely explode in 3.19.
Fix it by using a pair of helper functions that deal with the
actual hardware.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mach-imx directly references to the irq field in
struct irq_data, and uses this to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different.
Just replacing all instances of irq with hwirq fixes the issue.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/dt
Merge "ARM: BCM5301X: DT changes for v3.19 #2" from Hauke Mehrtens:
ARM: BCM5301X: dts updates
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
based SoCs
This patch enables the MAX77686 PMIC drivers in the multi_v7_defconfig used
on exynos4412-prime family of SoCs [1]. The exynos4412-prime based boards
are producing the following runtime errors only on the multi_v7_defconfig [2]:
kern.err: deviceless supply vdd_arm not found, using dummy regulator
kern.err: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage to 1287500
kern.err: cpufreq: __target_index: Failed to change cpu frequency: -22
I reviewed the exynos_defconfig, which does not produce these runtime
errors. It was obvious that the exynos_defconfig has the PMIC drivers
enabled, whereas the multi_v7_defconfig does not. This patch has been tested
on a odroid-u2 and a odroid-u3 board. It has resolved the runtime errors.
Therefore, I purpose we enabled these drivers in the multi_v7_defconfig.
[1] http://www.hardkernel.com/main/products/prdt_info.php?g_code=G135270682824
[2] http://storage.armcloud.us/kernel-ci/mainline/v3.18-rc7-48-g7cc78f8/arm-multi_v7_defconfig/lab-tbaker-00/boot-exynos4412-odroidu3.html
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The existing MCE code calls flush_tlb hook with IS=0 (single page) resulting
in partial invalidation of TLBs which is not right. This patch fixes
that by passing IS=0xc00 to invalidate whole TLB for successful recovery
from TLB and ERAT errors.
Cc: stable@vger.kernel.org
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
upatepp can get called for a nohpte fault when we find from the linux
page table that the translation was hashed before. In that case
we are sure that there is no existing translation, hence we could
avoid doing tlbie.
We could possibly race with a parallel fault filling the TLB. But
that should be ok because updatepp is only ever relaxing permissions.
We also look at linux pte permission bits when filling hash pte
permission bits. We also hold the linux pte busy bits while
inserting/updating a hashpte entry, hence a paralle update of
linux pte is not possible. On the other hand mprotect involves
ptep_modify_prot_start which cause a hpte invalidate and not updatepp.
Performance number:
We use randbox_access_bench written by Anton.
Kernel with THP disabled and smaller hash page table size.
86.60% random_access_b [kernel.kallsyms] [k] .native_hpte_updatepp
2.10% random_access_b random_access_bench [.] doit
1.99% random_access_b [kernel.kallsyms] [k] .do_raw_spin_lock
1.85% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
1.26% random_access_b [kernel.kallsyms] [k] .native_flush_hash_range
1.18% random_access_b [kernel.kallsyms] [k] .__delay
0.69% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
0.37% random_access_b [kernel.kallsyms] [k] .clear_user_page
0.34% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
0.32% random_access_b [kernel.kallsyms] [k] fast_exception_return
0.30% random_access_b [kernel.kallsyms] [k] .hash_page_mm
With Fix:
27.54% random_access_b random_access_bench [.] doit
22.90% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
5.76% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
5.20% random_access_b [kernel.kallsyms] [k] fast_exception_return
5.12% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
4.80% random_access_b [kernel.kallsyms] [k] .hash_page_mm
3.31% random_access_b [kernel.kallsyms] [k] data_access_common
1.84% random_access_b [kernel.kallsyms] [k] .trace_hardirqs_on_caller
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/cleanup
Pull "Fifth batch of cleanup/SoC for 3.19" from Nicolas Ferre:
- removal of now dead code and AT91-specific driver
- removal of !DT initialization in some core AT91 drivers
- simplification of Kconfig DT board file selection: now automatic
* tag 'at91-cleanup5' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
Pull "First batch of defconfigs for AT91 / 3.19:" from Nicolas Ferre:
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
commit 68a3c0433077 ([media] ARM: OMAP2: RX-51: update
si4713 platform data) updated board-rx51-peripherals.c
so that si4713 could be easily used on DT boot, but
it ended up introducing a build warning whenever
si4713 isn't enabled.
This patches fixes that warning:
arch/arm/mach-omap2/board-rx51-peripherals.c:1000:36: warning: \
‘rx51_si4713_platform_data’ defined but not used [-Wunused-variable]
static struct si4713_platform_data rx51_si4713_platform_data = {
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "last dts changes for 3.19" from Jason Cooper:
- rk3288 thermal driver that got accepted into the thermal tree
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
* tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: dts: rockchip: enable thermal on rk3288-evb board
ARM: dts: rockchip: add main thermal info to rk3288
ARM: dts: rockchip: add RK3288 Thermal data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This chip is present on at91sam9261ek board: add it to the at91_dt_defconfig.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
As this touch button driver is used on at91sam9x5ek, it's better to enable it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This is the selection of the new PWM driver using TC Blocks. This driver is
useful so we enable it in both sama5 and at91_dt defconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add the Atmel eXtended DMA Controller driver option. This driver is first used
on SAMA5D4 SoCs and only relevant in sama5_defconfig file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add neon support for sama5d4 and large blocks/files support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This commit adjusts the registration of the cpufreq-dt driver in the
mvebu platform to indicate to the cpufreq driver that the platform has
independent clocks for each CPU.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt2
Pull "ARM: tegra: Device tree changes for v3.19" from Thierry Reding:
The bulk of these changes add memory controller nodes for Tegra30,
Tegra114 and Tegra124. The memory controller implements an IOMMU that
the display controllers are attached to. This allows them to scan out
physically non-contiguous framebuffers and removes one of the primary
users of CMA.
The only other change adds a new MIPI pad control bank to the pin
controller on Tegra124. The corresponding driver patch for this went
into v3.18 as:
3ccc11f6b82c pinctrl: tegra: Add MIPI pad control
* tag 'tegra-for-3.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable IOMMU for display controllers on Tegra124
ARM: tegra: Enable IOMMU for display controllers on Tegra114
ARM: tegra: Enable IOMMU for display controllers on Tegra30
ARM: tegra: Add memory controller support for Tegra124
ARM: tegra: Add memory controller support for Tegra114
ARM: tegra: Add memory controller support for Tegra30
ARM: tegra: Add APB_MISC_GP as a MIPI pad control bank
These additional commits are merged as dependencies:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "ARM: tegra: IOMMU support for v3.19" from Thierry Reding:
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
* tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
