| Age | Commit message (Collapse) | Author |
|---|
|
There are some efforts going on to have flexcan_switch function
implemented in flexcan driver, so that this platform function hook
can be saved for device tree boot. But due to the mx28evk board
design oddness that two flexcan transceivers share one switch gpio,
we have to come up a separate and generic gpio-switch driver to handle
all these gpio switch use cases.
Before that happens, we choose to use auxdata to pass flexcan_switch
function hook, so that the DT conversion is not blocked there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
For non-DT boot, function tx28_add_fec0 configures all ENET0 pins
into gpio mode for resetting fec phy, and then reconfigures those pins
into ENET function after that.
For DT boot, all the pin configuration is done by pinctrl subsystem.
Ideally, when gpio_request gets called, GPIO subsystem should call
pinctrl to configure pins into gpio mode automatically, and have pins
freed up from pinctrl subsystem when gpio_free is called. But right
now, this cooperation between gpio and pinctrl hasn't been available.
As the result, we have to explicitly call pinctrl_get_select and
pinctrl_put for device tree boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There is no need for adding board related entries into dt_board_compat.
Leave only the SoC entry.
This way we do not need to patch a C file when adding dt support for
a new board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Added missed clkmux setting for mx28evk.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add AUART0 support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: intc: Handle domain association for sparseirq pre-allocated vectors.
sh: sh7269: Fix LCD pinmux
sh: dma: fix request_irq usage
|
|
Pull two sparc fixes from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
|
|
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull three dma-mapping fixes from Marek Szyprowski.
* 'fixes-for-linus-for-3.6-rc2' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: fix incorrect freeing of atomic allocations
ARM: dma-mapping: fix atomic allocation alignment
ARM: mm: fix MMU mapping of CMA regions
|
|
ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.
Since this can not possibly work, it's better to disable i2c
support entirely on this board.
Without this patch, building davinci_all_defconfig results in:
arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Andrey Porodko <panda@chelcom.ru>
|
|
Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.
Without this patch, building tct_hammer_defconfig results in:
net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)
The size of vmlinux increases by 1.78% because of this:
size obj-arm/vmlinux.nobug
text data bss dec hex filename
2108474 116916 55352 2280742 22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
text data bss dec hex filename
2150804 116916 53696 2321416 236c08 obj-arm/vmlinux
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
|
|
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.
Without this patch, building exynos_defconfig results in:
arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.
drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
|
|
Without this patch, building integrator_defconfig results in:
arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.
Without this patch, building s3c2410_defconfig results in:
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
|
|
The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.
Without this patch, building hackkit_defconfig results in:
arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.
In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.
As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.
Without this patch, building raumfeld_defconfig results in:
drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
Commit 3d55c29 "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:
1) That patch only created the vdd_sys regulator when booting using a
board file. Since this is the root of the whole regulator tree, this
caused no regulators to successfully initialize when booting using
device tree. The registration of vdd_sys is moved to fix this.
2) When booting use DT, the regulator core sets has_full_constraints,
which in turn causes the core to turn off any regulators not marked
as always on. Some of the affected regulators are required for basic
system operation. To solve this, add always on constraints to all
relevant regulators. This doesn't affect booting using a board file
since nothing sets has_full_constraints in that case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit e9da6e9905e639b0f842a244bc770b48ad0523e9 (ARM: dma-mapping:
remove custom consistent dma region) changed the way atomic allocations
are handled. However, arm_dma_free() was not modified accordingly, and
as a result freeing of atomic allocations does not work correctly when
CMA is disabled. Memory is leaked and following WARNINGs are seen:
[ 57.698911] ------------[ cut here ]------------
[ 57.753518] WARNING: at arch/arm/mm/dma-mapping.c:263 arm_dma_free+0x88/0xe4()
[ 57.811473] trying to free invalid coherent area: e0848000
[ 57.867398] Modules linked in: sata_mv(-)
[ 57.921373] [<c000d270>] (unwind_backtrace+0x0/0xf0) from [<c0015430>] (warn_slowpath_common+0x50/0x68)
[ 58.033924] [<c0015430>] (warn_slowpath_common+0x50/0x68) from [<c00154dc>] (warn_slowpath_fmt+0x30/0x40)
[ 58.152024] [<c00154dc>] (warn_slowpath_fmt+0x30/0x40) from [<c000dc18>] (arm_dma_free+0x88/0xe4)
[ 58.219592] [<c000dc18>] (arm_dma_free+0x88/0xe4) from [<c008fa30>] (dma_pool_destroy+0x100/0x148)
[ 58.345526] [<c008fa30>] (dma_pool_destroy+0x100/0x148) from [<c019a64c>] (release_nodes+0x144/0x218)
[ 58.475782] [<c019a64c>] (release_nodes+0x144/0x218) from [<c0197e10>] (__device_release_driver+0x60/0xb8)
[ 58.614260] [<c0197e10>] (__device_release_driver+0x60/0xb8) from [<c0198608>] (driver_detach+0xd8/0xec)
[ 58.756527] [<c0198608>] (driver_detach+0xd8/0xec) from [<c0197c54>] (bus_remove_driver+0x7c/0xc4)
[ 58.901648] [<c0197c54>] (bus_remove_driver+0x7c/0xc4) from [<c004bfac>] (sys_delete_module+0x19c/0x220)
[ 59.051447] [<c004bfac>] (sys_delete_module+0x19c/0x220) from [<c0009140>] (ret_fast_syscall+0x0/0x2c)
[ 59.207996] ---[ end trace 0745420412c0325a ]---
[ 59.287110] ------------[ cut here ]------------
[ 59.366324] WARNING: at arch/arm/mm/dma-mapping.c:263 arm_dma_free+0x88/0xe4()
[ 59.450511] trying to free invalid coherent area: e0847000
[ 59.534357] Modules linked in: sata_mv(-)
[ 59.616785] [<c000d270>] (unwind_backtrace+0x0/0xf0) from [<c0015430>] (warn_slowpath_common+0x50/0x68)
[ 59.790030] [<c0015430>] (warn_slowpath_common+0x50/0x68) from [<c00154dc>] (warn_slowpath_fmt+0x30/0x40)
[ 59.972322] [<c00154dc>] (warn_slowpath_fmt+0x30/0x40) from [<c000dc18>] (arm_dma_free+0x88/0xe4)
[ 60.070701] [<c000dc18>] (arm_dma_free+0x88/0xe4) from [<c008fa30>] (dma_pool_destroy+0x100/0x148)
[ 60.256817] [<c008fa30>] (dma_pool_destroy+0x100/0x148) from [<c019a64c>] (release_nodes+0x144/0x218)
[ 60.445201] [<c019a64c>] (release_nodes+0x144/0x218) from [<c0197e10>] (__device_release_driver+0x60/0xb8)
[ 60.634148] [<c0197e10>] (__device_release_driver+0x60/0xb8) from [<c0198608>] (driver_detach+0xd8/0xec)
[ 60.823623] [<c0198608>] (driver_detach+0xd8/0xec) from [<c0197c54>] (bus_remove_driver+0x7c/0xc4)
[ 61.013268] [<c0197c54>] (bus_remove_driver+0x7c/0xc4) from [<c004bfac>] (sys_delete_module+0x19c/0x220)
[ 61.203472] [<c004bfac>] (sys_delete_module+0x19c/0x220) from [<c0009140>] (ret_fast_syscall+0x0/0x2c)
[ 61.393390] ---[ end trace 0745420412c0325b ]---
The patch fixes this.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
The alignment mask is calculated incorrectly. Fixing the calculation
makes strange hangs/lockups disappear during the boot with Amstrad E3
and 3.6-rc1 kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Fix dma_contiguous_remap() so that it continues through all the
regions, even after encountering one that is outside lowmem.
Without this change, if you have two CMA regions, the first outside
lowmem and the seocnd inside lowmem, only the second one will get
set up in the MMU. Data written to that region then doesn't get
automatically flushed from the cache into memory.
Signed-off-by: Chris Brand <cbrand@broadcom.com>
[extended patch subject with 'fix' word]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
|
|
There are two ports that can output the LCD data, therefore
they have to use separate pimux identifiers so we can select
the one we want to use.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
When calling request_irq with IRQF_SHARED, the dev cookie must be set
(i.e. non-NULL), otherwise the code rejects it immediately with -EINVAL.
So restore the logic here where we'd pass a pointer to the name as a
dummy unique val.
Otherwise, booting up on my LANDISK system would fail with:
DMAC Address Error0 request_irq fail
This was introduced in commit 7f47c7189b3e8f19a589f77a3ad169d7b691b582.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The native 31 bit and the compat behaviour for the mmap system calls differ:
In native 31 bit mode the passed in address for the mmap system call will be
unmodified passed to sys_mmap_pgoff().
In compat mode however the passed in address will be modified with
compat_ptr() which masks out the most significant bit.
The result is that in native 31 bit mode each mmap request (with MAP_FIXED)
will fail where the most significat bit is set, while in compat mode it
may succeed.
This odd behaviour was introduced with d3815898 "[S390] mmap: add missing
compat_ptr conversion to both mmap compat syscalls".
To restore a consistent behaviour accross native and compat mode this
patch functionally reverts the above mentioned commit.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The compat wrappers incorrectly called the non compat versions of
the system process_vm system calls.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
There are multiple errors in how sys_32_personality() handles personality
flags stored in top three bytes.
- directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
- directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Fix the first one by properly using personality() macro to compare only
PER_MASK bytes.
Fix the second one by setting only the bits that should be set, instead of
overwriting the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
It's unused, so remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
ARM i.MX fixes for 3.6-rc
* tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
i.MX27: Fix emma-prp and csi clocks.
ARM: clk-imx31: Fix the keypad clock name
ARM: dts: imx27-3ds.dts: Fix serial console node
|
|
Just a small typo fix to make lsxl dtbs compile
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Naming of emma-prp related clocks for the i.MX27 is not correct.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Integrator timer is using the clock framework to get the
timer frequency, but missed to prepare the clock before enabling.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
* 'mxs/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: always build ocotp
ARM: mxs: Remove MMAP_MIN_ADDR setting from mxs_defconfig
ARM: mx28: Fix registers range
ARM: mx23: Fix registers range
|
|
With this patch ocotp support will always be build into the kernel on mxs.
Otherwise a DT-only kernel fails to link with:
arch/arm/mach-mxs/mach-mxs.c:169: undefined reference to `mxs_get_ocotp'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The CONFIG_DEFAULT_MMAP_MIN_ADDR was set to 65536 in mxs_defconfig,
this caused severe breakage of userland applications since the upper
limit for ARM is 32768. By default CONFIG_DEFAULT_MMAP_MIN_ADDR is
set to 4096 and can also be changed via /proc/sys/vm/mmap_min_addr
if needed.
Quoting Russell King [1]:
"4096 is also fine for ARM too. There's not much point in having
defconfigs change it - that would just be pure noise in the config
files."
the CONFIG_DEFAULT_MMAP_MIN_ADDR can be removed from the defconfig
altogether.
This problem was introduced by commit cde7c41 (ARM: configs: add
defconfig for mach-mxs).
[1] http://marc.info/?l=linux-arm-kernel&m=134401593807820&w=2
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI and power management fixes from Len Brown:
"A 3.3 sleep regression fixed, numa bugfix, plus some minor cleanups"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI processor: Fix tick_broadcast_mask online/offline regression
ACPI: Only count valid srat memory structures
ACPI: Untangle a return statement for better readability
ACPI / PCI: Do not try to acquire _OSC control if that is hopeless
ACPI: delete _GTS/_BFS support
ACPI/x86: revert 'x86, acpi: Call acpi_enter_sleep_state via an asmlinkage C function from assembler'
ACPI: replace strlen("string") with sizeof("string") -1
ACPI / PM: Fix build warning in sleep.c for CONFIG_ACPI_SLEEP unset
|
|
Pull KVM bug fixes from Marcelo Tosatti:
- Fix DS/ES segment register corruption on x86_32.
- Fix kvmclock wallclock migration offset.
- Fix PIT interrupt ACK vs system reset logic bug.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Fix ds/es corruption on i386 with preemption
KVM: x86: apply kvmclock offset to guest wall clock time
KVM: PIC: call ack notifiers for irqs that are dropped form irr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Various fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, kcmp: The kcmp system call can be common
arch/x86/kernel/kdebugfs.c: Ensure a consistent return value in error case
x86/mce: Add quirk for instruction recovery on Sandy Bridge processors
x86/mce: Move MCACOD defines from mce-severity.c to <asm/mce.h>
x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
x86, nops: Missing break resulting in incorrect selection on Intel
x86: CONFIG_CC_STACKPROTECTOR=y is no longer experimental
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix merge window fallout and fix sleep profiling (this was always
broken, so it's not a fix for the merge window - we can skip this one
from the head of the tree)."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/trace: Add ability to set a target task for events
perf/x86: Fix USER/KERNEL tagging of samples properly
perf/x86/intel/uncore: Make UNCORE_PMU_HRTIMER_INTERVAL 64-bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
m68k/apollo: Rename "timer" to "apollo_timer"
zorro: Remove unused zorro_bus.devices
m68k: Remove never used asm/shm.h
m68k/sun3: Remove unselectable code in prom_init()
m68k: Use asm-generic version of <asm/sections.h>
m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
mtd/uclinux: Use generic __bss_stop instead of _ebss
m68knommu: Allow ColdFire CPUs to use unaligned accesses
m68k: Remove five unused headers
m68k: CPU32 does not support unaligned accesses
m68k: Introduce config option CPU_HAS_NO_UNALIGNED
m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
m68k: Move CPU_HAS_* config options
m68k: Remove duplicate FPU config option
m68knommu: Clean up printing of sections
m68k: Use asm-generic version of <asm/types.h>
m68k: Use Kbuild logic to import asm-generic headers
|
|
Commit 88cde8b (ARM: dts: imx: update #interrupt-cells for gpio nodes)
changes gpio #interrupt-cells from 1 to 2 without updating the users.
It causes the gpio irq requesting call failing in client driver's probe
function.
Add the irq type cell for those gpio interrupt users to fix their
driver probe failure.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Since commit c7e963f (net/smsc911x: Add regulator support), the lan9220
device tree probe fails on imx53-ard board, because the commit makes
VDD33A and VDDVARIO supplies mandatory for the driver.
Add a fixed dummy 3V3 supplying lan9220 to fix the regression.
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
