Age | Commit message (Collapse) | Author |
|
Add PCIe support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The PMIC interrupt was changed from modul revision 1 to 2. Revision 1 was
declared as a prototype and is not in series by any customers.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The nand is on the module (PFL-A-02) and not on the baseboard (PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The gmpi and fec node were not in alphabatical order.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
ST-M41T0M6 is available on Colibri carrier boards.
Hence enable M41T0M6 RTC.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
imx6q-tbs2910 board uses sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Since restructuring of the device tree files, the USB misc/phy
nodes are disabled by default. Hence we need to enable those
explicitly when USB is used.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Use GPIO support by adding SD card detection configuration and
GPIO pinmux for Colibri's standard GPIO pins. Attach the GPIO
pins to the iomuxc node to get the GPIO pin settings applied.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Audio on phyFLEX boards is presented by tlv320aic3007 codec connected
over SSI interface.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.
This patch fixes i2c2, i2c3 pin configuration which caused messages:
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add Colibri VF50 device tree files vf500-colibri.dtsi and
vf500-colibri-eval-v3.dts, in line with the Colibri VF61 device tree
files. However, to minimize dupplication we also add vf-colibri.dtsi
and vf-colibri-eval-v3.dtsi which contain the common device tree
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This adds more generic base device trees for Vybrid SoCs. There
are three series of Vybrid SoC commonly available:
- VF3xx series: single core, Cortex-A5 without external memory
- VF5xx series: single core, Cortex-A5
- VF6xx series: dual core, Cortex-A5/Cortex-M4
The second digit represents the presents of a L2 cache (VFx1x).
The VF3xx series are not suitable for Linux especially since the
internal memory is quite small (1.5MiB).
The VF500 is essentially the base SoC, with only one core and
without L1 cache. The VF610 is a superset of the VF500, hence
vf500.dtsi is then included and enhanced by vf610.dtsi. There is
no board using VF510 or VF600 currently, but, if needed, they can
be added easily.
The Linux kernel can also run on the Cortex-M4 CPU of Vybrid
using !MMU support. This patchset creates a device tree structure
which allows to share peripherals nodes for a VF6xx Cortex-M4
device tree too. The two CPU types have different views of the
system: Foremost they are using different interrupt controllers,
but also the memory map is slightly different. The base device
tree vfxxx.dtsi allows to create SoC and board level device trees
supporting the Cortex-M4 while reusing the shared peripherals
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.
This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.
For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This add Freescale QorIQ LS1021A SoC device tree support.
The QorIQ LS1021A processor incorporates dual ARM Cortex-A7 cores,
providing virtualization support, advanced security features and the
broadest array of high-speed interconnects and optimized peripheral
features.
The LS1021A SoC shares IPs with i.MX, Vybrid and PowerPC platform.
For the detail information about Freescale QorIQ LS1021A SoC,
please refer to the QorIQ LS1021A Reference Manual.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On registration I2C bus drivers attemp to get ids from device tree
aliases, add a missing alias for I2C4 found on iMX6 DualLite/Solo.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
compatible for fec2 node to be compatible with the old version.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add all required properties for the cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Enable ADC support for Colibri VF61 modules
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The Colibri standard defines four pins as PWM outputs, two of them (PWM
A and C) are routed to FTM instance 0 and the other two (PWM B and D)
are routed to FTM instance 1. Hence enable both FTM instances for the
Colibri module and mux the four pins accordingly.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add Global Timer support which is part of the private peripherals
of the Cortex-A5 processor. This Global Timer is compatible with the
Cortex-A9 implementation. It's a 64-bit timer and is clocked by the
peripheral clock, which is typically 133 or 166MHz on Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The newly introduced LS1021A SoC selects CONFIG_SOC_FSL, which
is originally symbol used for the PowerPC based platforms
and guards lots of code that does not build on ARM.
This breaks allmodconfig, so let's remove it for now, until
either all those drivers are fixed or they use a dependency
on IMX instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
With the clock assignment device tree changes, the clocks get
initialized properly but the search for those clocks fails with
errors:
[ 0.000000] i.MX clk 4: register failed with -17
[ 0.000000] i.MX clk 5: register failed with -17
This is because the module can't find those clocks anymore, and
tries to initialize fixed clocks with the same name.
Get the clock modules input clocks from the assigned clocks by
default by using of_clk_get_by_name(). If this function returns
not a valid clock, fall back to the old behaviour and search the
input clock from the device tree's /clocks/$name node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Instanciate device for the generic cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.
While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This is the bypass clock used to feed the ARM partition
while we reprogram PLL1 to another rate.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add enet init for i.mx6sx:
- Add phy ar8031 fixup
- Set enet clock source from internal PLL
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Add the ARM Global Timer as clocksource/scheduler clock option and
use it as default scheduler clock. This leaves the PIT timer for
other users e.g. the secondary Cortex-M4 core. Also, the Global Timer
has double the precission (running at pheripheral clock compared to
IPG clock) and a 64-bit incrementing counter register. We still keep
the PIT timer as an secondary option in case the ARM Global Timer is
not available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
For LPDDR2 platform, no need to enable weak2P5 in DSM mode,
it can be pulled down to save power(~0.65mW).
And per design team's recommendation, we should disconnect
VDDHIGH and SNVS in DSM mode on i.MX6SL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
As the DDR/IO and MMDC setting are different on LPDDR2 and DDR3,
we used cpu type to decide how to do these settings in suspend
before which is NOT flexible, take i.MX6SL for example, although
it has LPDDR2 on EVK board, but users can also use DDR3 on other
boards, so it is better to read the DDR type from MMDC then decide
how to do related settings.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Stock firmware on rk3288 does not initizalize the CNTVOFF registers
of the architected timer correctly. This introduces issues with the
newly added SMP support for rk3288, resulting in rcu stalls due to
differing timer values per core.
There exist preliminary and tested patches for u-boot for this problem,
but there are a minority of boards using other bootloaders like coreboot.
There also is currently a second solution for miss-initialized architected
timers in the works:
- clocksource: arch_timer: Fix code to use physical timers when requested
- clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
Therefore disable smp on rk3288 again till these are finalized, also
allowing coreboot-based boards to boot again.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
sclk_mfc is required for MFC device since commit
0c2272170d78f826f6e97f99fb8a67fc17feef07 ("media: s5p-mfc: rename
special clock to sclk_mfc"), so add it to exynos4 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This ensures the core and the audio subsystem clocks are configured
properly, as expected by the sound machine driver. These bits are
missing to obtain proper audio sample rates in kernel v3.17, where
audio support for Odroid X2/U3 was first added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Pull in to receive 54ef6df3f3f1 ("rcu: Provide counterpart to
rcu_dereference() for non-RCU situations").
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The HP Chromebook 11 uses an Atmel maXTouch as trackpad.
The keymap was found by trial-and-error.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Spotted in the Chrome OS 3.8 based device tree.
Needs CONFIG_SENSORS_LM90.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds max77693-haptic node to support for haptic motor driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch add PWM(Pulse Width Modulation) node and
handle to use pwm property.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|