| Age | Commit message (Collapse) | Author |
|---|
|
Recent arm64 builds using CONFIG_ARM64_64K_PAGES are failing with:
arch/arm64/kernel/perf_regs.c: In function ‘perf_reg_abi’:
arch/arm64/kernel/perf_regs.c:41:2: error: implicit declaration of function ‘is_compat_thread’
arch/arm64/kernel/perf_event.c:1398:2: error: unknown type name ‘compat_uptr_t’
This is due to some recent arm64 perf commits with compat support:
commit 23c7d70d55c6d9:
ARM64: perf: add support for frame pointer unwinding in compat mode
commit 2ee0d7fd36a3f8:
ARM64: perf: add support for perf registers API
Those patches make the arm64 kernel unbuildable if CONFIG_COMPAT is not
defined and CONFIG_ARM64_64K_PAGES depends on !CONFIG_COMPAT. This patch
allows the arm64 kernel to build with and without CONFIG_COMPAT.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This reverts commit 82b2f495fba338d1e3098dde1df54944a9c19751. The
__boot_cpu_mode variable is flushed in head.S after being written,
therefore the additional cache flushing is no longer required.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).
This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The current TCR register setting in arch/arm64/mm/proc.S assumes that
TCR_EL1.TG* fields are one bit wide and bit 31 is RES1 (reserved, set to
1). With the addition of 16K pages (currently unsupported in the
kernel), the TCR_EL1.TG* fields have been extended to two bits. This
patch updates the corresponding Linux definitions and drops the bit 31
setting in proc.S in favour of the new macros.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Joe Sylve <joe.sylve@gmail.com>
|
|
Since this macro is identical to pgprot_writecombine() and is only used
in a single place, remove it completely to avoid confusion. On ARMv7+
processors, the coherent DMA mapping must be Normal NonCacheable (a.k.a.
writecombine) to avoid mismatched hardware attribute aliases (with the
kernel linear mapping as Normal Cacheable).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
DMA_ATTR_WRITE_COMBINE is currently ignored. Set the pgprot
appropriately for non coherent opperations.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The current dma_ops do not specify an mmap function so maping
falls back to the default implementation. There are at least
two issues with using the default implementation:
1) The pgprot is always pgprot_noncached (strongly ordered)
memory even with coherent operations
2) dma_common_mmap calls virt_to_page on the remapped non-coherent
address which leads to invalid memory being mapped.
Fix both these issue by implementing a custom mmap function which
correctly accounts for remapped addresses and sets vm_pg_prot
appropriately.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[catalin.marinas@arm.com: replaced "arm64_" with "__" prefix for consistency]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Without this, the following scenario is incorrectly determined
to be invalid.
addr 0x7f_ffffe000 size 8192 addr_limit 0x80_00000000
This behavior was observed while trying to vmsplice the stack
as part of a CRIU dump of a process on a system started with the
norandmaps kernel parameter.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Probably due to rebasing over the lengthy time it took to get the patch
merged commit addea9ef055b (cpufreq: enable ARM drivers on arm64) added
a duplicate Power management options section. Add CPUfreq to the CPU
power management section and remove a duplicate include of the main
power section.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Rather than have separate hugetlb and transparent huge page pmd
manipulation functions, re-wire our thp functions to simply call the
pte equivalents.
This allows THP to take advantage of the new PTE_WRITE logic introduced
in:
c2c93e5 arm64: mm: Introduce PTE_WRITE
To represent splitting THPs we use the PTE_SPECIAL bit as this is not
used for pmds.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
asm-generic offers an atomic-add based rwsem implementation, which
can avoid the need for heavier, spinlock-based synchronisation on the
fast path.
This patch makes use of the optimised implementation for arm64 CPUs.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This enables support for the generic CPU feature modalias implementation that
wires up optional CPU features to udev based module autoprobing.
A file <asm/cpufeature.h> is provided that maps CPU feature numbers to
elf_hwcap bits, which is the standard way on arm64 to advertise optional CPU
features both internally and to user space.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[catalin.marinas@arm.com: removed unnecessary "!!"]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Make smp_spin_table_cpu_postboot() static, because this function
is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Make local symbols static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add support for unwinding using the dwarf information in compat
mode. Using the correct user stack pointer allows perf to record
the frames correctly in the native and compat modes.
Note that although the dwarf frame unwinding works ok using
libunwind in native mode (on ARMv7 & ARMv8), some changes are
required to the libunwind code for the compat mode. Those changes
are posted separately on the libunwind mailing list.
Tested on ARMv8 platform with v8 and compat v7 binaries, the latter
are statically built.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When profiling a 32-bit application, user space callchain unwinding
using the frame pointer is performed in compat mode. The code is taken
over from the AARCH32 code and adapted to work on AARCH64.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch implements the functions required for the perf registers API,
allowing the perf tool to interface kernel register dumps with libunwind
in order to provide userspace backtracing.
Compat mode is also supported.
Only the general purpose user space registers are exported, i.e.:
PERF_REG_ARM_X0,
...
PERF_REG_ARM_X28,
PERF_REG_ARM_FP,
PERF_REG_ARM_LR,
PERF_REG_ARM_SP,
PERF_REG_ARM_PC
and not the PERF_REG_ARM_V* registers.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
ARMv8 supports a range of physical address bit sizes. The PARange bits
from ID_AA64MMFR0_EL1 register are read during boot-time and the
intermediate physical address size bits are written in the translation
control registers (TCR_EL1 and VTCR_EL2).
There is no change in the VA bits and levels of translation.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Reviewed-by: Will Deacon <Will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Special pte mappings are not intended to be executable and do not even
have an associated struct page. This patch ensures that we do not call
__sync_icache_dcache() on such ptes.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Steve Capper <Steve.Capper@arm.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Cc: <stable@vger.kernel.org>
|
|
pgprot_{dmacoherent,writecombine,noncached} don't need to generate
executable mappings with side-effects like __sync_icache_dcache() being
called when the mapping is in user space.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Cc: <stable@vger.kernel.org>
|
|
Commit 8adbf57fc429 ("irqchip: gic: use dmb ishst instead of dsb when
raising a softirq") added an explicit dmb(...) call to the GIC driver.
This patch adds a simple dmb() macro to arm64, which expands to a DMB SY
instruction.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add basic CPU topology support to arm64, based on the existing pre-v8
code and some work done by Mark Hambleton. This patch does not
implement any topology discovery support since that should be based on
information from firmware, it merely implements the scaffolding for
integration of topology support in the architecture.
No locking of the topology data is done since it is only modified during
CPU bringup with external serialisation from the SMP code.
The goal is to separate the architecture hookup for providing topology
information from the DT parsing in order to ease review and avoid
blocking the architecture code (which will be built on by other work)
with the DT code review by providing something simple and basic.
Following patches will implement support for interpreting topology
information from MPIDR and for parsing the DT topology bindings for ARM,
similar patches will be needed for ACPI.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: removed CONFIG_CPU_TOPOLOGY, always on if SMP]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This adds support for advertising the presence of ARMv8 Crypto
Extensions in the Aarch32 execution state to 32-bit ELF binaries
running in 32-bit compat mode under the arm64 kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add support for the ELF auxv entry AT_HWCAP2 when running 32-bit
ELF binaries in compat mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Currently we flush the entire dcache at boot within __cpu_setup, but
this is unnecessary as the booting protocol demands that the dcache is
invalid and off upon entering the kernel. The presence of the cache
flush only serves to hide bugs in bootloaders, and is not safe in the
presence of SMP.
In an SMP boot scenario the CPUs enter coherency outside of the kernel,
and the primary CPU enables its caches before bringing up secondary
CPUs. Therefore if any secondary CPU has an entry in its cache (in
violation of the boot protocol), the primary CPU might snoop it even if
the secondary CPU's cache is disabled. The boot-time cache flush only
serves to hide a firmware bug, and slows down a cpu boot unnecessarily.
This patch removes the unnecessary boot-time cache flush.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: make __flush_dcache_all local only]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Enable cpufreq and power kconfig menus on arm64 along with arm cpufreq
drivers. The power menu is needed for OPP support. At least on Calxeda
systems, the same cpufreq driver is used for arm and arm64 based
systems.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
psci_init() is written to return err code if something goes wrong. However,
the single user, setup_arch(), doesn't care about it. Moreover, every error
path is supplied with a clear message which is enough for pleasant debugging.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Since 652af899799354049b273af897b798b8f03fdd88 "arm64: factor out spin-table
boot method" psci prefix's been introduced. We have a common pr_fmt, so clean
them up.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch adds support for DMA API cache maintenance on SoCs without
hardware device cache coherency.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Since arm64 does not support ISA, there is no need for early swiotlb
initialisation. This patch switches the DMA mapping code to
swiotlb_tlb_late_init_with_default_size(). A side effect of this is that
GFP_DMA is used for the swiotlb buffer and devices with a 32-bit
coherent mask are correctly supported.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
On arm64 we do not have two DMA zones, so it does not make sense to
implement ZONE_DMA32. This patch changes ZONE_DMA32 with ZONE_DMA, the
latter covering 32-bit dma address space to honour GFP_DMA allocations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Remove some unnecessary bits that were apparently carried over from
another architecture's implementation:
- No need to get_page() the vdso text/data - these are part of the
kernel image.
- No need for ClearPageReserved on the vdso text.
- No need to vmap the first text page to check the ELF header - this
can be done through &vdso_start.
Also some minor cleanup:
- Use kcalloc for vdso_pagelist array allocation.
- Don't print on allocation failure, slab/slub will do that for us.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
arm64_swiotlb_alloc/free_coherent name can be misleading
somtimes with CMA support being enabled after this
patch (c2104debc235b745265b64d610237a6833fd53)
Change this name to be more generic:
__dma_alloc/free_coherent
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
[catalin.marinas@arm.com: renamed arm64_swiotlb_dma_ops to coherent_swiotlb_dma_ops]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Change the soft_restart() routine to call cpu_reset() at its identity mapped
physical address.
The cpu_reset() routine must be called at its identity mapped physical address
so that when the MMU is turned off the instruction pointer will be at the correct
location in physical memory.
Signed-off-by: Geoff Levand <geoff@infradead.org> for Huawei, Linaro
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch changes the idmap page table creation during boot to cover
the whole kernel image, allowing functions like cpu_reset() to be safely
called with the physical address.
This patch also simplifies the create_block_map asm macro to no longer
take an idmap argument and always use the phys/virt/end parameters. For
the idmap case, phys == virt.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Over the past couple of years, the generic mmu_gather gained range
tracking - 597e1c3580b7 (mm/mmu_gather: enable tlb flush range in generic
mmu_gather), 2b047252d087 (Fix TLB gather virtual address range
invalidation corner cases) - and tlb_fast_mode() has been removed -
29eb77825cc7 (arch, mm: Remove tlb_fast_mode()).
The new mmu_gather structure is now suitable for arm64 and this patch
converts the arch asm/tlb.h to the generic code. One functional
difference is the shift_arg_pages() case where previously the code was
flushing the full mm (no tlb_start_vma call) but now it flushes the
range given to tlb_gather_mmu() (possibly slightly more efficient
previously).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
The patch moves the PCI I/O space (currently at 64K) before the
earlyprintk mapping and extends it to 16MB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
processor debug state PSTATE.D is unmasked in smp call
clear_os_lock for secondary cpus. So debug state is still
masked in normal kernel context. With this patch, unmask
debug state on secondary boot for the cpus in normal kernel
context. Now kgdb tests passed with multicore.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add HAVE_ARCH_KGDB for arm64 Kconfig
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
typecast instruction_pointer macro to unsigned long to
resolve following compiler warnings like
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 2 has type 'u64' [-Wformat]
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add KGDB software step debugging support for EL1 debug
in AArch64 mode.
KGDB registers step debug handler with debug monitor.
On receiving 'step' command from GDB tool, target enables
software step debugging and step address is updated in ELR.
Software Step debugging is disabled when 'continue' command
is received
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add KGDB debug support for kernel debugging.
With this patch, basic KGDB debugging is possible.GDB register
layout is updated and GDB tool can establish connection with
target and can set/clear breakpoints.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add macros to enable and disable to manage PSTATE.D
for debugging. The macros local_dbg_save and local_dbg_restore
are moved to irqflags.h file
KGDB boot tests fail because of PSTATE.D is masked.
unmask it for debugging support
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- a bugfix which prevents a divide by 0 panic when the newly introduced
try_msr_calibrate_tsc() fails
- enablement of the Baytrail platform to utilize the newfangled msr
based calibration
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: tsc: Add missing Baytrail frequency to the table
x86, tsc: Fallback to normal calibration if fast MSR calibration fails
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixlets from all around the place"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore: Fix IVT/SNB-EP uncore CBOX NID filter table
perf/x86: Correctly use FEATURE_PDCM
perf, nmi: Fix unknown NMI warning
perf trace: Fix ioctl 'request' beautifier build problems on !(i386 || x86_64) arches
perf trace: Add fallback definition of EFD_SEMAPHORE
perf list: Fix checking for supported events on older kernels
perf tools: Handle PERF_RECORD_HEADER_EVENT_TYPE properly
perf probe: Do not add offset twice to uprobe address
perf/x86: Fix Userspace RDPMC switch
perf/x86/intel/p6: Add userspace RDPMC quirk for PPro
|
|
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
|
|
This patch updates the CBOX PMU filters mapping tables for SNB-EP
and IVT (model 45 and 62 respectively).
The NID umask always comes in addition to another umask.
When set, the NID filter is applied.
The current mapping tables were missing some code/umask
combinations to account for the NID umask. This patch
fixes that.
Cc: mingo@elte.hu
Cc: ak@linux.intel.com
Reviewed-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140219131018.GA24475@quad
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The current code simply assumes Intel Arch PerfMon v2+ to have
the IA32_PERF_CAPABILITIES MSR; the SDM specifies that we should check
CPUID[1].ECX[15] (aka, FEATURE_PDCM) instead.
This was found by KVM which implements v2+ but didn't provide the
capabilities MSR. Change the code to DTRT; KVM will also implement the
MSR and return 0.
Cc: pbonzini@redhat.com
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140203132903.GI8874@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When using BTS on Core i7-4*, I get the below kernel warning.
$ perf record -c 1 -e branches:u ls
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317893] Uhhuh. NMI received for unknown reason 31 on CPU 2.
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317920] Do you have a strange power saving mode enabled?
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
kernel:[ 438.317945] Dazed and confused, but trying to continue
Make intel_pmu_handle_irq() take the full exit path when returning early.
Cc: eranian@google.com
Cc: peterz@infradead.org
Cc: mingo@kernel.org
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392425048-5309-1-git-send-email-andi@firstfloor.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
