| Age | Commit message (Collapse) | Author |
|---|
|
Commit 171c067 ("ARM: EXYNOS: add support uart for EXYNOS4 and
EXYNOS5") renames S5P_PA_UARTn to EXYNOS4_PA_UARTn. Hence we
need to do similar modification in mach-exynos4-dt.c to fix
compilation error.
arch/arm/mach-exynos/mach-exynos4-dt.c:40:2: error: 'S5P_PA_UART0'
undeclared here (not in a function)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file is including the SoC specific devices and properties. And
adds the dts file for SMDK5250 board which uses the EXYNOS5250
dts file. Its board specific properites will be added later.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds a new EXYNOS5 compatible device tree enabled board
When using this, a corresponding device tree blob which describes the
board's properties should be supplied at boot time to the kernel.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile update to run "make minconfig" on the tile defconfigs
from Chris Metcalf.
This removes almost three thousand lines of inane defconfig chatter.
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile/configs: convert to minimal configs via "make savedefconfig"
|
|
Adding struct _sigchld_x32 caused a misalignment cascade in struct
siginfo, because union _sifields is located on an 4-byte boundary
(8-byte misaligned.)
Adding new fields that are 8-byte aligned caused the intermediate
structures to also be aligned to 8 bytes, thereby adding padding in
unexpected places.
Thus, change s64 to compat_s64 here, which makes it "misaligned on
paper". In reality these fields *are* actually aligned (there are 3
preceeding ints outside the union and 3 inside struct _sigchld_x32),
but because of the intervening union and struct it is not possible for
gcc to avoid padding without breaking the ABI.
Reported-and-tested-by: H. J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1329696488-16970-1-git-send-email-hpa@zytor.com
|
|
When handling Interrupt Source Override in MADT table, the default
ISA IRQ trigger model and polarity should be edge-rising.
Current IA64 implmentation doesn't follow the specification and
set default ISA IRQ trigger model as level-low. With that wrong
configuration and when system runs out of interrupt vectors,
it will cause vector sharing among edge triggered ISA IRQ and
level triggered PCI IRQ, then interrupt storm. So change the code
to follow the specification.
Signed-off-by: Liu Jiang <jiang.liu@huawei.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
In i.MX35-PDK, OV2640 camera is populated on the
personality board. This camera is registered as a subdevice via soc-camera interface.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This patch adds framebuffer support for freescale mx35 3ds board
Signed-off-by: Wu Guoxing <b39297@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This patch adds support cpufreq for EXYNOS5250 SoC. Basically,
the exynos-cpufreq.c is used commonly and exynos5250-cpufreq.c
is used for EXYNOS5250(two Cortex-A15 cores) SoC.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch adds support cpufreq for EXYNOS4X12 SoCs. Basically,
the exynos-cpufreq.c is used commonly and exynos4x12-cpufreq.c
is used for EXYNOS4212(two Cortex-A9 cores) and EXYNOS4412(four
Cortex-A9 cores) SoCs.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This patch changes to use ioremap() for EXYNOS4210
so that we can drop the static mapping for EXYNOS
SoCs.
Note: Will be updated for all of Samsung GPIOlibs
to use ioremap() next time.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds support regarding GPIO definitions for
EXYNOS5250 and change the macro of GPIO numbering to use
EXYNOS4 and EXYNOS5 SoCs.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds CONFIG_ARCH_EXYNOS5 and CONFIG_SOC_EXYNOS5250
for supporting EXYNOS5250 SoC and allows supporting EXYNOS4
and EXYNOS5 together.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The EXYNOS5250 has two Cortex-A15 cores and there's no
need to call scu_enable() in platform_smp_prepare_cpus()
because Cortex-A15 has no regarding scu register which
can be used for getting number of cores.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The GPIOs of EXYNOS4 and EXYNOS5 are changed to use
ioremap instead of static mapping. It alse causes the
change of external interrupt IO mapping. This patch
changes EXYNOS4 to EXYNOS for common use and changes
EINT_x macros for supporting dynamic IO mapping.
Signed-off-by: Eunki Kim <eunki_kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds the interrupt definitions for EXYNOS5250 at
<mach/irqs.h> file and it is needed for EXYNOS5250 SoC.
As a note, for single zImage of EXYNOS4 and EXYNOS5, prefix
of EXYNOS4_ and EXYNOS5_ has been added.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Patch adds x86_64 assembler implementation of Camellia block cipher. Two set of
functions are provided. First set is regular 'one-block at time' encrypt/decrypt
functions. Second is 'two-block at time' functions that gain performance increase
on out-of-order CPUs. Performance of 2-way functions should be equal to 1-way
functions with in-order CPUs.
Patch has been tested with tcrypt and automated filesystem tests.
Tcrypt benchmark results:
AMD Phenom II 1055T (fam:16, model:10):
camellia-asm vs camellia_generic:
128bit key: (lrw:256bit) (xts:256bit)
size ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B 1.27x 1.22x 1.30x 1.42x 1.30x 1.34x 1.19x 1.05x 1.23x 1.24x
64B 1.74x 1.79x 1.43x 1.87x 1.81x 1.87x 1.48x 1.38x 1.55x 1.62x
256B 1.90x 1.87x 1.43x 1.94x 1.94x 1.95x 1.63x 1.62x 1.67x 1.70x
1024B 1.96x 1.93x 1.43x 1.95x 1.98x 2.01x 1.67x 1.69x 1.74x 1.80x
8192B 1.96x 1.96x 1.39x 1.93x 2.01x 2.03x 1.72x 1.64x 1.71x 1.76x
256bit key: (lrw:384bit) (xts:512bit)
size ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B 1.23x 1.23x 1.33x 1.39x 1.34x 1.38x 1.04x 1.18x 1.21x 1.29x
64B 1.72x 1.69x 1.42x 1.78x 1.81x 1.89x 1.57x 1.52x 1.56x 1.65x
256B 1.85x 1.88x 1.42x 1.86x 1.93x 1.96x 1.69x 1.65x 1.70x 1.75x
1024B 1.88x 1.86x 1.45x 1.95x 1.96x 1.95x 1.77x 1.71x 1.77x 1.78x
8192B 1.91x 1.86x 1.42x 1.91x 2.03x 1.98x 1.73x 1.71x 1.78x 1.76x
camellia-asm vs aes-asm (8kB block):
128bit 256bit
ecb-enc 1.15x 1.22x
ecb-dec 1.16x 1.16x
cbc-enc 0.85x 0.90x
cbc-dec 1.20x 1.23x
ctr-enc 1.28x 1.30x
ctr-dec 1.27x 1.28x
lrw-enc 1.12x 1.16x
lrw-dec 1.08x 1.10x
xts-enc 1.11x 1.15x
xts-dec 1.14x 1.15x
Intel Core2 T8100 (fam:6, model:23, step:6):
camellia-asm vs camellia_generic:
128bit key: (lrw:256bit) (xts:256bit)
size ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B 1.10x 1.12x 1.14x 1.16x 1.16x 1.15x 1.02x 1.02x 1.08x 1.08x
64B 1.61x 1.60x 1.17x 1.68x 1.67x 1.66x 1.43x 1.42x 1.44x 1.42x
256B 1.65x 1.73x 1.17x 1.77x 1.81x 1.80x 1.54x 1.53x 1.58x 1.54x
1024B 1.76x 1.74x 1.18x 1.80x 1.85x 1.85x 1.60x 1.59x 1.65x 1.60x
8192B 1.77x 1.75x 1.19x 1.81x 1.85x 1.86x 1.63x 1.61x 1.66x 1.62x
256bit key: (lrw:384bit) (xts:512bit)
size ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B 1.10x 1.07x 1.13x 1.16x 1.11x 1.16x 1.03x 1.02x 1.08x 1.07x
64B 1.61x 1.62x 1.15x 1.66x 1.63x 1.68x 1.47x 1.46x 1.47x 1.44x
256B 1.71x 1.70x 1.16x 1.75x 1.69x 1.79x 1.58x 1.57x 1.59x 1.55x
1024B 1.78x 1.72x 1.17x 1.75x 1.80x 1.80x 1.63x 1.62x 1.65x 1.62x
8192B 1.76x 1.73x 1.17x 1.78x 1.80x 1.81x 1.64x 1.62x 1.68x 1.64x
camellia-asm vs aes-asm (8kB block):
128bit 256bit
ecb-enc 1.17x 1.21x
ecb-dec 1.17x 1.20x
cbc-enc 0.80x 0.82x
cbc-dec 1.22x 1.24x
ctr-enc 1.25x 1.26x
ctr-dec 1.25x 1.26x
lrw-enc 1.14x 1.18x
lrw-dec 1.13x 1.17x
xts-enc 1.14x 1.18x
xts-dec 1.14x 1.17x
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch add support for EXYNOS5250 SoC has two Cortex-A15 cores.
Since actually, most codes in mach-exynos/ are used commonly for
EXYNOS4 and EXYNOS5 the EXYNOS5/EXYNOS5250 has been implemented
in mach-exynos/.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Actually, the base address of uart is different between EXYNOS4
and EXYNOS5 and this patch enables to support uart for EXYNOS4
and EXYNOS5 SoCs at runtime.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In all of Samsung platform, the setup-i2c0.c file for I2C channel 0
is always compiled. So when supporting new SoC,it should be updated
for it. Since EXYNOS5 GPIO will be supported after this, there is no
setup gpio in there now. It will be implemented with that, of course.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds clock-exynos5.c for EXYNOS5250 now
and that can be used for other EXYNOS5 SoCs later.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Since exynos4_init_uarts() can be used for EXYNOS5 SoCs,
this patch changes the name of function to exynos_init_uarts().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
According to commit cc511b8d84d8 ("ARM: 7257/1: EXYNOS: introduce
arch/arm/mach-exynos/common.[ch]"), we don't need to declare extern
for exynos4_map_io(), exynos4_init_clocks(), exynos4_init_uarts(),
and exynos_init(). And the exynos4210_register_clocks() and
exynos4212_register_clocks depend on each SoC not ARCH_EXYNOS4.
So this patch fixed above.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The framebuffer driver needs the clock named 'lcd' as its bus
clock but the equivalent clock on Exynos4 is named as 'fimd'.
Hence, create a clkdev lookup entry with the name 'lcd' that
references the 'fimd' clock.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[kgene.kim@samsung.com: rebased on top of latest samsung tree]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The existing pcmcia platform_device structure is not used and is not needed by
the pending hx4700 PCMCIA/CF support. So let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
Move APIC ID validity check into platform APIC code, so it can
be overridden when needed. For NumaChip systems, always trust
MADT, as it's constructed with high APIC IDs.
Behaviour verifies on standard x86 systems and on NumaChip
systems with this, and compile-tested with allyesconfig.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Reviewed-by: Steffen Persvold <sp@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1331709454-27966-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Update to the almost-final v3.3 kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Drive the two Bluetooth UART output GPIOs (GPIO43_BTUART_TXD, GPIO45_BTUART_RTS)
LOW during sleep mode instead of HIGH. This reduces sleep mode battery discharge
from approximately 46 mA to approximately 30 mA.
Signed-off-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
GPIO105 (nIR_ON) is requested twice: first in gpio_request_array(), then in
pxa_irda_probe(). Consequently the second request fails with EBUSY:
pxa2xx-ir: probe of pxa2xx-ir failed with error -16
This patch removes the first request, allowing pxa_irda_probe() to succeed.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/mce
Apply two miscellaneous MCE fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix a stray ! which flipped the sense if we were generating a signal
frame for ia32 vs. x32.
Introduced in:
e7084fd5 x32: Switch to a 64-bit clock_t
Reported-by: H. J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Gregory M. Lueck <gregory.m.lueck@intel.com>
Link: http://lkml.kernel.org/r/1329696488-16970-1-git-send-email-hpa@zytor.com
|
|
Several platforms incorrectly use __io() for casting to 'void __iomem *'.
This converts all of those uses to use the common IOMEM macro.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-sh@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Several platforms create IOMEM defines for casting to 'void __iomem *',
and other platforms are incorrectly using __io() macro for the same
purpose. This creates a common definition and removes all the platform
specific versions. Rather than try to make linux/io.h and asm/io.h
assembly safe, the assembly version of IOMEM is moved into
asm/assembler.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Newer version of binutils are more strict about specifying the
correct options to enable certain classes of instructions.
The sparc32 build is done for v7 in order to support sun4c systems
which lack hardware integer multiply and divide instructions.
So we have to pass -Av8 when building the assembler routines that
use these instructions and get patched into the kernel when we find
out that we have a v8 capable cpu.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the include of ep93xx-regs.h from files which no longer need
it, notably include/mach/hardware.h.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
The EP93XX_SYSCON defines are now no longer needed outside of the
EP93xx SoC core code, so they can be moved to a private header.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
The crunch code in arch/arm/kernel is specific to the EP93xx. Move it
to the mach-ep93xx directory. This removes the need for the
EP93XX_SYSCON defines to be exported to arch/arm/kernel.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
The syscon access functions are no longer used outside of the core
EP93xx code. Move their definitions into the SoC code.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Move the pinmux setting of the EP93xx GPIOs to the core code. This
removes the need for the GPIO driver to have access to the system
controller registers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Move the AHB/APB peripheral defines to local SoC header since they are
only needed by the core SoC code. The UART defines are not moved
because they are used by the mach/uncompress.h header.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert the ep93xx watchdog driver into a platform device and
remove it's dependency on <mach/hardware.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
The ep93xx backlight driver uses a single register within the
framebuffer's register space. Currently the backlight driver uses a
static IO mapping for the register since the memory cannot be
requested by both drivers.
Convert the static mapping to use ioremap so that we can remove the
dependency on mach/hardware.h. To do so, we need remove the
request_mem_region from both the backlight and framebuffer drivers,
since whichever driver is loaded second will fail with -EBUSY
otherwise.
A proper fix is still required, and a FIXME comment has been added to
both drivers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Move the GPIO related defines out of ep93xx-regs.h and into
gpio-ep93xx.h where they belong.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Both the Snapper CL15 and EDB93xx audio drivers set the same audio
configuration in ep93xx_i2s_acquire. Remove the arguments to
ep93xx_i2s_acquire so that the audio drivers no longer need the
EP93XX_SYSCON defines exported.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
The PHYS_BASE defines in arch/arm/mach-ep93xx/include/mach-ep93xx-regs.h are
only used in the SoC code. Move the defines to a local header file.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into next/soc
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas: (234 commits)
ARM: shmobile: remove additional __io() macro use
ARM: mach-shmobile: default to no earlytimer
ARM: mach-shmobile: r8a7779 and Marzen timer rework
ARM: mach-shmobile: r8a7740 and Bonito timer rework
ARM: mach-shmobile: sh73a0, AG5EVM and Kota2 timer rework
ARM: mach-shmobile: sh7372, AP4EVB and Mackerel timer rework
ARM: mach-shmobile: sh7377 and G4EVM timer rework
ARM: mach-shmobile: sh7367 and G3EVM timer rework
ARM: mach-shmobile: add shmobile_earlytimer_init()
ARM: mach-shmobile: Move sh7372 AP4EVB external clk setup
ARM: mach-shmobile: Move sh7372 Mackerel external clk setup
ARM: mach-shmobile: rename clk_init() to shmobile_clk_init()
ARM: mach-shmobile: r8a7779 L2 cache support
ARM: mach-shmobile: r8a7779 map_io and init_early update
ARM: mach-shmobile: r8a7740 map_io and init_early update
ARM: mach-shmobile: sh73a0 map_io and init_early update
ARM: mach-shmobile: sh7372 map_io and init_early update
ARM: mach-shmobile: sh7377 map_io and init_early update
ARM: mach-shmobile: sh7367 map_io and init_early update
sh: remove clk_ops
...
(includes an update to v3.3-rc7)
Conflicts:
arch/arm/mach-omap2/id.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile update from Chris Metcalf
"These include a couple of queued-up minor bug fixes from the
community, a fix to unbreak the sysfs hooks in tile, and syncing up
the defconfigs."
Ugh. defconfigs updates without "make minconfig". Tons of ugly
pointless lines there, I suspect.
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: Use set_current_blocked() and block_sigmask()
arch/tile: misplaced parens near likely
arch/tile: sync up the defconfig files to the tip
arch/tile: Fix up from commit 8a25a2fd126c621f44f3aeaef80d51f00fc11639
|
|
setup-r8a7779.c has grown a new user of the __io() macro. Rob Herring's
PIO cleanup series already gets rid of all other uses in shmobile, so
we should ensure that this one gets removed as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
