| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit bd52276fa1d4 ("x86-64/efi: Use EFI to deal with
platform wall clock (again)"), and the two supporting commits:
da5a108d05b4: "x86/kernel: remove tboot 1:1 page table creation code"
185034e72d59: "x86, efi: 1:1 pagetable mapping for virtual EFI calls")
as they all depend semantically on commit 53b87cf088e2 ("x86, mm:
Include the entire kernel memory map in trampoline_pgd") that got
reverted earlier due to the problems it caused.
This was pointed out by Yinghai Lu, and verified by me on my Macbook Air
that uses EFI.
Pointed-out-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
|
|
Pull microblaze update from Michal Simek:
"The main change is UAPI for Microblaze."
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: signal: Declare do_notify_resume
microblaze: lib: Add lib function declarations
microblaze: lib: Remove helper macros
microblaze: Add static qualifiers
microblaze: Wire-up new system call kcmp
microblaze: Fix intc_enable_or_unmask function
microblaze: Do not initialized regs->r1 twice in ELF_PLAT_INIT
microblaze: Remove passing the second arg to schedule_tail
UAPI: (Scripted) Disintegrate arch/microblaze/include/asm
microblaze: uaccess.h: Fix timerfd syscall
microblaze: Remove BIP from childregs
|
|
Pull crypto update from Herbert Xu:
- Added aesni/avx/x86_64 implementations for camellia.
- Optimised AVX code for cast5/serpent/twofish/cast6.
- Fixed vmac bug with unaligned input.
- Allow compression algorithms in FIPS mode.
- Optimised crc32c implementation for Intel.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (32 commits)
crypto: caam - Updated SEC-4.0 device tree binding for ERA information.
crypto: testmgr - remove superfluous initializers for xts(aes)
crypto: testmgr - allow compression algs in fips mode
crypto: testmgr - add larger crc32c test vector to test FPU path in crc32c_intel
crypto: testmgr - clean alg_test_null entries in alg_test_descs[]
crypto: testmgr - remove fips_allowed flag from camellia-aesni null-tests
crypto: cast5/cast6 - move lookup tables to shared module
padata: use __this_cpu_read per-cpu helper
crypto: s5p-sss - Fix compilation error
crypto: picoxcell - Add terminating entry for platform_device_id table
crypto: omap-aes - select BLKCIPHER2
crypto: camellia - add AES-NI/AVX/x86_64 assembler implementation of camellia cipher
crypto: camellia-x86_64 - share common functions and move structures and function definitions to header file
crypto: tcrypt - add async speed test for camellia cipher
crypto: tegra-aes - fix error-valued pointer dereference
crypto: tegra - fix missing unlock on error case
crypto: cast5/avx - avoid using temporary stack buffers
crypto: serpent/avx - avoid using temporary stack buffers
crypto: twofish/avx - avoid using temporary stack buffers
crypto: cast6/avx - avoid using temporary stack buffers
...
|
|
This reverts commit 53b87cf088e2ea68d7c59619d0214cc15bb76133.
It causes odd bootup problems on x86-64. Markus Trippelsdorf gets a
repeatable oops, and I see a non-repeatable oops (or constant stream of
messages that scroll off too quickly to read) that seems to go away with
this commit reverted.
So we don't know exactly what is wrong with the commit, but it's
definitely problematic, and worth reverting sooner rather than later.
Bisected-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: H Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Change the value of status to disabled to keep the consistent
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix the following sparse warnings in the OMAP3/4 CPUIdle code:
arch/arm/mach-omap2/cpuidle34xx.c:272:1: warning: symbol 'omap3_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle34xx.c:274:23: warning: symbol 'omap3_idle_driver' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:164:1: warning: symbol 'omap4_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:166:23: warning: symbol 'omap4_idle_driver' was not declared. Should it be static?
Also fix the following checkpatch warnings:
WARNING: please, no space before tabs
#44: FILE: arch/arm/mach-omap2/cpuidle34xx.c:105:
+^I.name = ^I"omap3_idle",$
WARNING: please, no space before tabs
#45: FILE: arch/arm/mach-omap2/cpuidle34xx.c:106:
+^I.owner = ^ITHIS_MODULE,$
ERROR: code indent should use tabs where possible
#211: FILE: arch/arm/mach-omap2/cpuidle44xx.c:74:
+ /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */$
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Booting OMAP4460 Pandaboard ES with a recent u-boot results in this
warning:
WARNING: at arch/arm/mach-omap2/dpll3xxx.c:427 omap3_noncore_dpll_enable+0xf4/0x110()
The OMAP4 DPLL parent clock names only listed the reference clocks,
not the bypass clocks. Fix by adding the bypass clocks to the DPLL
parent lists.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
The OMAP4 clock divider "div_iva_hs_clk" is listed in the clock data
as an OMAP HSDIVIDER, but it's actually a power-of-two divider. This
causes a warning during boot on an OMAP4460 Pandaboard-ES with a
recent u-boot:
WARNING: at arch/arm/mach-omap2/clkt_clksel.c:143 omap2_clksel_recalc+0xf4/0x12c()
clock: div_iva_hs_clk: could not find fieldval 0 for parent dpll_core_m5x2_ck
Fix by converting the data for this clock to a power-of-two divider.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
Commit d043d87 (ARM: OMAP2+: clockdomain: bypass clockdomain handling
when disabling unused clks) skips the decrementing of a clock-domains
use count if the clocks use count is zero. However, for OMAP4 devices
this is causing the EMU clock-domain to be stuck ON as the use count is
not getting decremented correctly.
The scenario that leads to this problem is described below ...
omap_hwmod_setup_all
--> _setup
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 1
--> _enable_clocks
--> clk_enable
--> trace_clk_div_div usecount = 1
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 2
--> _idle
--> _disable_clocks
--> clk_disable
--> trace_clk_div_div usecount = 0
--> clkdm_hwmod_disable
--> skips decrement of EMU clock domain usecount
because trace_clk_div_div is 0!
--> EMU clock domain usecount = 2
--> clkdm_hwmod_disable
--> EMU clock domain usecount = 1
Hence, due to the order that a clocks use count is decremented and the
clock domain is disabled, it is possible that the clock domain can have
a non-zero use count when the actual clock has a use count of 0.
Therefore, we should only bypass the clock-domain handling when both the
clock-domain and clock in the clock-domain have a use count of 0 and
warn when the clock-domain has a zero use count and the clock has a
non-zero use count.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.
The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.
If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.
This problem only appears to occur on OMAP4460 and not OMAP4430.
Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.
This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.
When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.
New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.
The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).
Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.infradead.org/users/dhowells/linux-headers
Pull x86 UAPI disintegration from David Howells.
This is the scripted disintegration of the uapi headers for x86, now
that most of the x86 updates for 3.8 are hopefully merged.
* tag 'disintegrate-x86-20121214' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate arch/x86/include/asm
|
|
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
|
|
We need to move this file to allow ARM multiplatform configurations
to build for omap2+. This can now be done as this file now only
contains platform_data.
cc: Russell King <linux@arm.linux.org.uk>
cc: Alan Cox <alan@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Govindraj.R <govindraj.raja@ti.com>
cc: Kevin Hilman <khilman@ti.com>
cc: linux-serial@vger.kernel.org
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 0d9250c (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
"This branch contains device-tree updates for the SPEAr platform. They
had dependencies on earlier branches from this merge window, which is
why they were broken out in a separate branch."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
ARM: SPEAr1310: Fix AUXDATA for compact flash controller
ARM: SPEAr13xx: Remove fields not required for ssp controller
ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
ARM: SPEAr: DT: Update device nodes
ARM: SPEAr: DT: add uart state to fix warning
ARM: SPEAr: DT: Modify DT bindings for STMMAC
ARM: SPEAr: DT: Fix existing DT support
ARM: SPEAr: DT: Update partition info for MTD devices
ARM: SPEAr: DT: Update pinctrl list
ARM: SPEAr13xx: DT: Add spics gpio controller nodes
|
|
Pull ARM Soc updates, take 2, from Olof Johansson:
"This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that
we couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform."
Fix up conflicts mostly as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
sh: clkfwk: fixup unsed variable warning
Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
ARM: highbank: use common debug_ll_io_init
ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
ARM: shmobile: sh7372: remove fsidivx clock
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
|
|
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
|
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
|
|
Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.
* next/smp:
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP2420 H4 board was the only board using the
plat-omap/debug-devices.c code for configuring ethernet support. Now
that OMAP2420 H4 has been migrated to use the generic gpmc code for
configuring ethernet support, the debug-devices.c file is no longer
used and so remove it and its header file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Ethernet is not currently working on the OMAP2420 H4 board. In commit
f604931 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.
Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP_MODE_GPIO() macro verified only OMAP_MUX_MODE4.
It is not correct for following platforms:
2430 - gpio mux mode 3
44xx - gpio mux mode 3
54xx - gpio mux mode 6
Patch reserves first 3 bits in partition flags for storing gpio mux
mode in same format as stored in control pad register.
Modified OMAP_MODE_GPIO() macro to handle all possible cases of gpio mux mode.
Modified omap_mux_init() flags of omap34xx to include OMAP_MUX_GPIO_IN_MODE4.
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b84e88bf833d996997fda8f73276f2af
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined. Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.
However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.
This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.
The bug exists in v3.5+ kernels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Thomas Weber <thomas@tomweber.eu>
Cc: Thomas Weber <thomas@tomweber.eu>
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI update from Peter Anvin:
"EFI tree, from Matt Fleming. Most of the patches are the new efivarfs
filesystem by Matt Garrett & co. The balance are support for EFI
wallclock in the absence of a hardware-specific driver, and various
fixes and cleanups."
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
efivarfs: Make efivarfs_fill_super() static
x86, efi: Check table header length in efi_bgrt_init()
efivarfs: Use query_variable_info() to limit kmalloc()
efivarfs: Fix return value of efivarfs_file_write()
efivarfs: Return a consistent error when efivarfs_get_inode() fails
efivarfs: Make 'datasize' unsigned long
efivarfs: Add unique magic number
efivarfs: Replace magic number with sizeof(attributes)
efivarfs: Return an error if we fail to read a variable
efi: Clarify GUID length calculations
efivarfs: Implement exclusive access for {get,set}_variable
efivarfs: efivarfs_fill_super() ensure we clean up correctly on error
efivarfs: efivarfs_fill_super() ensure we free our temporary name
efivarfs: efivarfs_fill_super() fix inode reference counts
efivarfs: efivarfs_create() ensure we drop our reference on inode on error
efivarfs: efivarfs_file_read ensure we free data in error paths
x86-64/efi: Use EFI to deal with platform wall clock (again)
x86/kernel: remove tboot 1:1 page table creation code
x86, efi: 1:1 pagetable mapping for virtual EFI calls
x86, mm: Include the entire kernel memory map in trampoline_pgd
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 ACPI update from Peter Anvin:
"This is a patchset which didn't make the last merge window. It adds a
debugging capability to feed ACPI tables via the initramfs.
On a grander scope, it formalizes using the initramfs protocol for
feeding arbitrary blobs which need to be accessed early to the kernel:
they are fed first in the initramfs blob (lots of bootloaders can
concatenate this at boot time, others can use a single file) in an
uncompressed cpio archive using filenames starting with "kernel/".
The ACPI maintainers requested that this patchset be fed via the x86
tree rather than the ACPI tree as the footprint in the general x86
code is much bigger than in the ACPI code proper."
* 'x86-acpi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
X86 ACPI: Use #ifdef not #if for CONFIG_X86 check
ACPI: Fix build when disabled
ACPI: Document ACPI table overriding via initrd
ACPI: Create acpi_table_taint() function to avoid code duplication
ACPI: Implement physical address table override
ACPI: Store valid ACPI tables passed via early initrd in reserved memblock areas
x86, acpi: Introduce x86 arch specific arch_reserve_mem_area() for e820 handling
lib: Add early cpio decoder
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS update from Ingo Molnar:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space. These bits are exposed via
/sys/devices/system/machinecheck/machinecheck*/"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCA: Finish mca_config conversion
x86, MCA: Convert the next three variables batch
x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
x86, MCA: Convert dont_log_ce, banks and tolerant
drivers/base: Add a DEVICE_BOOL_ATTR macro
|
|
Use the newer idioms for setting PTRACE_O_xxx and PT_TRACE_xxx flags.
Only set/clear tile-specific flags if the generic routine returns
success, since otherwise we want to avoid setting any flags at all.
Atomically update the ptrace flags with the new values. Eliminate
the PT_TRACE_MASK_TILE bitmask and just shift PTRACE_O_MASK_TILE.
Add a BUILD_BUG_ON to avoid overlapping with generic bits.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Sparse generates the following warnings when compiling mach-omap2/timer.c.
CHECK arch/arm/mach-omap2/timer.c
arch/arm/mach-omap2/timer.c:193:13: warning: symbol 'omap_dmtimer_init'
was not declared. Should it be static?
arch/arm/mach-omap2/timer.c:213:12: warning: symbol
'omap_dm_timer_get_errata' was not declared. Should it be static?
Add static to function declaration to fix warnings.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
When compiling the kernel with configuration options ...
# CONFIG_ARCH_OMAP2 is not set
# CONFIG_ARCH_OMAP3 is not set
# CONFIG_ARCH_OMAP4 is not set
# CONFIG_SOC_OMAP5 is not set
CONFIG_SOC_AM33XX=y
... the following build warning is seen.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:395:19: warning: ‘omap2_sync32k_clocksource_init’
defined but not used [-Wunused-function]
This issue was introduced by commit 6f80b3b (ARM: OMAP2+: timer: remove
CONFIG_OMAP_32K_TIMER) where the omap2_sync32k_clocksource_init() is no
longer referenced by the timer initialisation function for the AM335x
device as it has no 32k-sync timer.
Fix this by adding the "__maybe_unused" compiler directive to the
omap2_sync32k_clocksource_init() function to indicate that this function
may be used for certain configurations.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
In commit fa6d79d (ARM: OMAP: Add initialisation for the real-time
counter), the function realtime_counter_init() was added. However, if
the kernel configuration option CONFIG_SOC_OMAP5 is not selected then
the following compiler warning is observed.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:489:20: warning: ‘realtime_counter_init’
defined but not used [-Wunused-function]
Commit fa6d79d also introduced the kernel configuration option
CONFIG_SOC_HAS_REALTIME_COUNTER. If this option is not selected then the
a stub function for realtime_counter_init() is defined.
For non-OMAP5 devices, there is no realtime counter and so
realtime_counter_init() function and stub function are not used for
these devices. Therefore, fix this warning by only allowing the kernel
configuration option CONFIG_SOC_HAS_REALTIME_COUNTER to be enabled for
OMAP5 devices.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Add support for reading the PCI function measurement block counters
provided by the hypervisor. Add two s390 debug features, one for
critical errors and one for tracing and provide wrappers to log data.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
|
|
Append the SEC IRQ after the IVG6, which is consistent to BF5xx SIC.
Exclude SIC irqchip fucntions from SEC code.
Call handle_fasteoi_irq in SEC error and fault handler.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
In commit d0a21265dfb5fa8a David Rientjes unified various archs'
module_alloc implementation (including x86) and removed the graduitous
shortcut for size == 0.
Then, in commit de7d2b567d040e3b, Joe Perches added a warning for
zero-length vmallocs, which can happen without kallsyms on modules
with no init sections (eg. zlib_deflate).
Fix this once and for all; the module code has to handle zero length
anyway, so get it right at the caller and remove the now-gratuitous
checks within the arch-specific module_alloc implementations.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42608
Reported-by: Conrad Kostecki <ConiKost@gmx.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
(This is just for Acks: this won't work without the actual syscall patches,
sitting in my tree for -next at the moment).
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Add finit_module syscall to the ARM syscall list.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
As part of the effort to create a stronger boundary between root and
kernel, Chrome OS wants to be able to enforce that kernel modules are
being loaded only from our read-only crypto-hash verified (dm_verity)
root filesystem. Since the init_module syscall hands the kernel a module
as a memory blob, no reasoning about the origin of the blob can be made.
Earlier proposals for appending signatures to kernel modules would not be
useful in Chrome OS, since it would involve adding an additional set of
keys to our kernel and builds for no good reason: we already trust the
contents of our root filesystem. We don't need to verify those kernel
modules a second time. Having to do signature checking on module loading
would slow us down and be redundant. All we need to know is where a
module is coming from so we can say yes/no to loading it.
If a file descriptor is used as the source of a kernel module, many more
things can be reasoned about. In Chrome OS's case, we could enforce that
the module lives on the filesystem we expect it to live on. In the case
of IMA (or other LSMs), it would be possible, for example, to examine
extended attributes that may contain signatures over the contents of
the module.
This introduces a new syscall (on x86), similar to init_module, that has
only two arguments. The first argument is used as a file descriptor to
the module and the second argument is a pointer to the NULL terminated
string of module arguments.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (merge fixes)
|
|
Pull KVM updates from Marcelo Tosatti:
"Considerable KVM/PPC work, x86 kvmclock vsyscall support,
IA32_TSC_ADJUST MSR emulation, amongst others."
Fix up trivial conflict in kernel/sched/core.c due to cross-cpu
migration notifier added next to rq migration call-back.
* tag 'kvm-3.8-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (156 commits)
KVM: emulator: fix real mode segment checks in address linearization
VMX: remove unneeded enable_unrestricted_guest check
KVM: VMX: fix DPL during entry to protected mode
x86/kexec: crash_vmclear_local_vmcss needs __rcu
kvm: Fix irqfd resampler list walk
KVM: VMX: provide the vmclear function and a bitmap to support VMCLEAR in kdump
x86/kexec: VMCLEAR VMCSs loaded on all cpus if necessary
KVM: MMU: optimize for set_spte
KVM: PPC: booke: Get/set guest EPCR register using ONE_REG interface
KVM: PPC: bookehv: Add EPCR support in mtspr/mfspr emulation
KVM: PPC: bookehv: Add guest computation mode for irq delivery
KVM: PPC: Make EPCR a valid field for booke64 and bookehv
KVM: PPC: booke: Extend MAS2 EPN mask for 64-bit
KVM: PPC: e500: Mask MAS2 EPN high 32-bits in 32/64 tlbwe emulation
KVM: PPC: Mask ea's high 32-bits in 32/64 instr emulation
KVM: PPC: e500: Add emulation helper for getting instruction ea
KVM: PPC: bookehv64: Add support for interrupt handling
KVM: PPC: bookehv: Remove GET_VCPU macro from exception handler
KVM: PPC: booke: Fix get_tb() compile error on 64-bit
KVM: PPC: e500: Silence bogus GCC warning in tlb code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen updates from Konrad Rzeszutek Wilk:
- Add necessary infrastructure to make balloon driver work under ARM.
- Add /dev/xen/privcmd interfaces to work with ARM and PVH.
- Improve Xen PCIBack wild-card parsing.
- Add Xen ACPI PAD (Processor Aggregator) support - so can offline/
online sockets depending on the power consumption.
- PVHVM + kexec = use an E820_RESV region for the shared region so we
don't overwrite said region during kexec reboot.
- Cleanups, compile fixes.
Fix up some trivial conflicts due to the balloon driver now working on
ARM, and there were changes next to the previous work-arounds that are
now gone.
* tag 'stable/for-linus-3.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/PVonHVM: fix compile warning in init_hvm_pv_info
xen: arm: implement remap interfaces needed for privcmd mappings.
xen: correctly use xen_pfn_t in remap_domain_mfn_range.
xen: arm: enable balloon driver
xen: balloon: allow PVMMU interfaces to be compiled out
xen: privcmd: support autotranslated physmap guests.
xen: add pages parameter to xen_remap_domain_mfn_range
xen/acpi: Move the xen_running_on_version_or_later function.
xen/xenbus: Remove duplicate inclusion of asm/xen/hypervisor.h
xen/acpi: Fix compile error by missing decleration for xen_domain.
xen/acpi: revert pad config check in xen_check_mwait
xen/acpi: ACPI PAD driver
xen-pciback: reject out of range inputs
xen-pciback: simplify and tighten parsing of device IDs
xen PVonHVM: use E820_Reserved area for shared_info
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 update from Martin Schwidefsky:
"Add support to generate code for the latest machine zEC12, MOD and XOR
instruction support for the BPF jit compiler, the dasd safe offline
feature and the big one: the s390 architecture gets PCI support!!
Right before the world ends on the 21st ;-)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390/qdio: rename the misleading PCI flag of qdio devices
s390/pci: remove obsolete email addresses
s390/pci: speed up __iowrite64_copy by using pci store block insn
s390/pci: enable NEED_DMA_MAP_STATE
s390/pci: no msleep in potential IRQ context
s390/pci: fix potential NULL pointer dereference in dma_free_seg_table()
s390/pci: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
s390/bpf,jit: add support for XOR instruction
s390/bpf,jit: add support MOD instruction
s390/cio: fix pgid reserved check
vga: compile fix, disable vga for s390
s390/pci: add PCI Kconfig options
s390/pci: s390 specific PCI sysfs attributes
s390/pci: PCI hotplug support via SCLP
s390/pci: CHSC PCI support for error and availability events
s390/pci: DMA support
s390/pci: PCI adapter interrupts for MSI/MSI-X
s390/bitops: find leftmost bit instruction support
s390/pci: CLP interface
s390/pci: base support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven.
Fix up trivial conflict (m68k switched to generic version of
uapi/asm/socket.h, net tree updated the old one) as per Geert.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/sun3: Fix instruction faults
m68k/sun3: Get interrupts working again
m68k: move to a single instance of free_initmem()
m68k: merge MMU and non-MMU versions of mm/init.c
m68k: switch to using the asm-generic termios.h
m68k: switch to using the asm-generic termbits.h
m68k: switch to using the asm-generic sockios.h
m68k: switch to using the asm-generic socket.h
m68k: switch to using the asm-generic shmbuf.h
m68k: switch to using the asm-generic sembuf.h
m68k: switch to using the asm-generic msgbuf.h
m68k: switch to using the asm-generic auxvec.h
m68k: switch to using the asm-generic shmparam.h
m68k: switch to using the asm-generic spinlock.h
m68k: switch to using the asm-generic hw_irq.h
arch/m68k: remove CONFIG_EXPERIMENTAL
|
|
Merge misc VM changes from Andrew Morton:
"The rest of most-of-MM. The other MM bits await a slab merge.
This patch includes the addition of a huge zero_page. Not a
performance boost but it an save large amounts of physical memory in
some situations.
Also a bunch of Fujitsu engineers are working on memory hotplug.
Which, as it turns out, was badly broken. About half of their patches
are included here; the remainder are 3.8 material."
However, this merge disables CONFIG_MOVABLE_NODE, which was totally
broken. We don't add new features with "default y", nor do we add
Kconfig questions that are incomprehensible to most people without any
help text. Does the feature even make sense without compaction or
memory hotplug?
* akpm: (54 commits)
mm/bootmem.c: remove unused wrapper function reserve_bootmem_generic()
mm/memory.c: remove unused code from do_wp_page()
asm-generic, mm: pgtable: consolidate zero page helpers
mm/hugetlb.c: fix warning on freeing hwpoisoned hugepage
hwpoison, hugetlbfs: fix RSS-counter warning
hwpoison, hugetlbfs: fix "bad pmd" warning in unmapping hwpoisoned hugepage
mm: protect against concurrent vma expansion
memcg: do not check for mm in __mem_cgroup_count_vm_event
tmpfs: support SEEK_DATA and SEEK_HOLE (reprise)
mm: provide more accurate estimation of pages occupied by memmap
fs/buffer.c: remove redundant initialization in alloc_page_buffers()
fs/buffer.c: do not inline exported function
writeback: fix a typo in comment
mm: introduce new field "managed_pages" to struct zone
mm, oom: remove statically defined arch functions of same name
mm, oom: remove redundant sleep in pagefault oom handler
mm, oom: cleanup pagefault oom handler
memory_hotplug: allow online/offline memory to result movable node
numa: add CONFIG_MOVABLE_NODE for movable-dedicated node
mm, memcg: avoid unnecessary function call when memcg is disabled
...
|
