| Age | Commit message (Collapse) | Author |
|---|
|
|
|
With the introduction of iomap changes platform init code
fails for emu.c if CONFIG_OMAP3_EMU is selected:
arch/arm/mach-omap2/emu.c:35:8: error:
'L4_EMU_34XX_BASE' undeclared here (not in a function)
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Building omap_devices should only be done at init time, and since
omap_device_build() is using early_platform calls which are also
__init, this ensures that omap_device isn't trying to use functions
that disappear.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that omap hsmmc init is split into two functions, it's safe
to mark omap_hsmmc_init and omap_mux related functions to __init.
This basically reverts the following fixes for the case where
TWL was compiled as a module:
a98f77b (ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup())
8930b4e (ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c)
Additionally it fixes up the remaining section warnings for
all callers of omap_mux functions.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Drivers should no longer use omap_read/write functions
but instead use ioremap + read/write functions.
As some USB legacy code is still shared between omap1 and
omap2420, let's limit the omap_read/write to plat/usb.h.
Note that the long term fix is to update the drivers to
use ioremap and read/write functions. That can now be
done as a separate patch series that is limited to the
USB drivers.
Also make sure the legacy omap1-keypad.c driver builds
if selected for 2420 based systems.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We don't want to keep it in io.h as we want to remove io.h
for omap2+ for the common zImage support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These should be local to omap2/3/4.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove omap_{read,write}l() from the 24xx PM code. The clocksource
code should now handle what this was supposed to do.
Tested on N800 -- but it's hard to say whether this fixes anything.
OMAP24xx static suspend path is currently broken, and this patch
doesn't change that.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Flag single_channel in struct omap2_mcspi_device_config is not used
by drivers/spi/spi-omap2-mcspi.c so we may remove it from include/plat/mcspi.h
and affected board files.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
into for-armsoc
|
|
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
With the removal of disable_fiq on rpc and addition MULTI_IRQ_HANDLER,
entry-macro.S is no longer needed for platforms that select
MULTI_IRQ_HANDLER and the include of it can be conditional.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Only rpc uses disable_fiq macro. Change it to a run-time installed
default FIQ handler. The handler is installed before FIQ is enabled
so the behavior should be unchanged.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
|
|
Only 3 platforms need arch_ret_to_user macro, so add ARCH_HAS_RET_TO_USER
kconfig option and make iop13xx, iop32x and iop33x select it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
|
|
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Expose omap_device_{alloc, delete, register} so we can use them outside
of omap_device.c.
This approach allows users, which need to manipulate an archdata member
of a device before it is registered, to do so. This is also useful
for users who have their devices created very early so they can be used
at ->reserve() time to reserve CMA memory.
The immediate use case for this is to set the private iommu archdata
member, which binds a device to its associated iommu controller.
This way, generic code will be able to attach omap devices to their
iommus, without calling any omap-specific API.
With this in hand, we can further clean the existing mainline OMAP iommu
driver and its mainline users, and focus on generic IOMMU approaches
for future users (rpmsg/remoteproc and the upcoming generic DMA API).
This patch is still considered an interim solution until DT fully materializes
for omap; at that point, this functionality will be removed as DT will
take care of creating the devices and configuring them correctly.
Tested on OMAP4 with a generic rpmsg/remoteproc that doesn't use any
omap-specific IOMMU API anymore.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we get the following error:
arch/arm/mach-omap2/built-in.o: In function `n8x0_mmc_callback':
twl-common.c:(.text+0x108a0): undefined reference to
`omap_mmc_notify_cover_event'
Fix this by warning about unusable MMC cover events.
The long term fix needs to change the MMC drivers to
register board specific callbacks directly with PMIC.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On some omaps twl4030_gpio has a callback to try to initialize
the MMC controller. If twl4030_gpio is compiled as a module,
bad things can happen because the callback function starts
calling functions that are supposed to be marked __init:
Kernel panic - not syncing: Attempted to kill the idle task!
twl4030_gpio twl4030_gpio: can't dispatch IRQs from modules
gpiochip_add: registered GPIOs 192 to 209 on device: twl4030
Unable to handle kernel paging request at virtual address b82a4c74
...
Additionally if this does not fail, warnings are produced
about trying to register the MMC multiple times.
Fix this by removing __init from omap_mux_get_by_name,
and add checks if omap2_hsmmc_init() is getting called more
than once.
Note that this will get fixed properly later on by splitting
omap2_hsmmc_init into two functions.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Here are a few more fixes for powerpc. Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.
Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.
Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point. For now let's just avoid
building it by default. Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
powerpc/adb: Use set_current_state()
powerpc: Disable interrupts early in Program Check
powerpc: Remove legacy iSeries from ppc64_defconfig
powerpc/fsl/pci: Fix PCIe fixup regression
powerpc: Fix kernel log of oops/panic instruction dump
|
|
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870ef3ff ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: Raphael Prevost <raphael@buro.asia>
Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 5b1cbac37798 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
events
perf on POWER stopped working after commit e050e3f0a71b (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
|
|
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since we are heading towards removing the Legacy iSeries platform, start
by no longer building it for ppc64_defconfig.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
=== Before the patch ===
[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500] 4e800020 3803ffd0 2b800009
<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500] 4e800020 3803ffd0 2b800009
=== After the patch ===
[ 51.385216] Instruction dump:
[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
<4>[ 51.385216] Instruction dump:
<4>[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The check for save_init_fpu() (introduced in commit 5b1cbac37798: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Quoth BenH:
"Here are a few powerpc fixes for 3.3, all pretty trivial. I also
added the patch to define GET_IP/SET_IP so we can use some more
asm-generic goodness."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries/eeh: Fix crash when error happens during device probe
powerpc/pseries: Fix partition migration hang in stop_topology_update
powerpc/powernv: Disable interrupts while taking phb->lock
powerpc: Fix WARN_ON in decrementer_check_overflow
powerpc/wsp: Fix IRQ affinity setting
powerpc: Implement GET_IP/SET_IP
powerpc/wsp: Permanently enable PCI class code workaround
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
|
|
EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.
Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This fixes a hang that was observed during live partition migration.
Since stop_topology_update must not be called from an interrupt
context, call it earlier in the migration process. The hang observed
can be seen below:
WARNING: at kernel/timer.c:1011
Modules linked in: ip6t_LOG xt_tcpudp xt_pkttype ipt_LOG xt_limit ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_raw xt_NOTRACK ipt_REJECT xt_state iptable_raw iptable_filter ip6table_mangle nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables ip6table_filter ip6_tables x_tables ipv6 fuse loop ibmveth sg ext3 jbd mbcache raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid10 raid1 raid0 scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc dm_round_robin dm_multipath scsi_dh sd_mod crc_t10dif ibmvfc scsi_transport_fc scsi_tgt scsi_mod dm_snapshot dm_mod
NIP: c0000000000c52d8 LR: c00000000004be28 CTR: 0000000000000000
REGS: c00000005ffd77d0 TRAP: 0700 Not tainted (3.2.0-git-00001-g07d106d)
MSR: 8000000000021032 <ME,CE,IR,DR> CR: 48000084 XER: 00000001
CFAR: c00000000004be20
TASK = c00000005ec78860[0] 'swapper/3' THREAD: c00000005ec98000 CPU: 3
GPR00: 0000000000000001 c00000005ffd7a50 c000000000fbbc98 c000000000ec8340
GPR04: 00000000282a0020 0000000000000000 0000000000004000 0000000000000101
GPR08: 0000000000000012 c00000005ffd4000 0000000000000020 c000000000f3ba88
GPR12: 0000000000000000 c000000007f40900 0000000000000001 0000000000000004
GPR16: 0000000000000001 0000000000000000 0000000000000000 c000000001022310
GPR20: 0000000000000001 0000000000000000 0000000000200200 c000000001029e14
GPR24: 0000000000000000 0000000000000001 0000000000000040 c00000003f74bc80
GPR28: c00000003f74bc84 c000000000f38038 c000000000f16b58 c000000000ec8340
NIP [c0000000000c52d8] .del_timer_sync+0x28/0x60
LR [c00000000004be28] .stop_topology_update+0x20/0x38
Call Trace:
[c00000005ffd7a50] [c00000005ec78860] 0xc00000005ec78860 (unreliable)
[c00000005ffd7ad0] [c00000000004be28] .stop_topology_update+0x20/0x38
[c00000005ffd7b40] [c000000000028378] .__rtas_suspend_last_cpu+0x58/0x260
[c00000005ffd7bf0] [c0000000000fa230] .generic_smp_call_function_interrupt+0x160/0x358
[c00000005ffd7cf0] [c000000000036ec8] .smp_ipi_demux+0x88/0x100
[c00000005ffd7d80] [c00000000005c154] .icp_hv_ipi_action+0x5c/0x80
[c00000005ffd7e00] [c00000000012a088] .handle_irq_event_percpu+0x100/0x318
[c00000005ffd7f00] [c00000000012e774] .handle_percpu_irq+0x84/0xd0
[c00000005ffd7f90] [c000000000022ba8] .call_handle_irq+0x1c/0x2c
[c00000005ec9ba20] [c00000000001157c] .do_IRQ+0x22c/0x2a8
[c00000005ec9bae0] [c0000000000054bc] hardware_interrupt_entry+0x18/0x1c
Exception: 501 at .cpu_idle+0x194/0x2f8
LR = .cpu_idle+0x194/0x2f8
[c00000005ec9bdd0] [c000000000017e58] .cpu_idle+0x188/0x2f8 (unreliable)
[c00000005ec9be90] [c00000000067ec18] .start_secondary+0x3e4/0x524
[c00000005ec9bf90] [c0000000000093e8] .start_secondary_prolog+0x10/0x14
Instruction dump:
ebe1fff8 4e800020 fbe1fff8 7c0802a6 f8010010 7c7f1b78 f821ff81 78290464
80090014 5400019e 7c0000d0 78000fe0 <0b000000> 4800000c 7c210b78 7c421378
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We need to disable interrupts when taking the phb->lock. Otherwise
we could deadlock with pci_lock taken from an interrupt.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With this change, helpers such as instruction_pointer() et al, get defined
in the generic header in terms of GET_IP
Removed the unnecessary definition of profile_pc in !CONFIG_SMP case as
suggested by Mike Frysinger.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: OMAP2+: board-generic: Add missing handle_irq callbacks
|
|
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
|
