| Age | Commit message (Collapse) | Author |
|---|
|
Git commit f4117ac9e237b74afdf5e001d5ea26a4d15e9847
introduced PLAT_PHYS_OFFSET, but headsmp.S was left
unchanged which results in a compile error:
AS arch/arm/mach-shmobile/headsmp.o
arch/arm/mach-shmobile/headsmp.S: Assembler messages:
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `secondary_startup' in operation
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `PHYS_OFFSET' in operation
make[1]: *** [arch/arm/mach-shmobile/headsmp.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Update the sh7372 clock code to set the RT side
set of MSTP bits to a fixed disabled state.
The sh7372 SoC contains two sets of MSTP bits,
one for the ARM (SYS) side, and one for the
SH4AL-DSP (RT) side. The actual clock associated
with the MSTP bit will only be stopped when both
sides have set the MSTP bit to disabled mode.
Some MSTP bits are enabled by default after
hardware reset, so this patch adjusts the code
to disable all MSTP bits associated with the RT
side to allow the SYS side to have full control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The PLLC2 clock on AP4 systems does not need to run constantly to be
able to use HDMI. The HDMI hotplug interrupt works without the PLL
too, after which all the necessary clocks will be turned on by the
runtime PM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Export the following sh7377 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Export the following sh7372 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Export the following sh7367 multimedia hardware blocks
using UIO: VPU, VEU[0-3], VEU2H, JPU and SPU1
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Update the sh7377 serial port types to make use of
PORT_SCIFA and PORT_SCIFB. This makes the software
match the sh7377 data sheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* Set receive enable and transmit enable bits of SCASCR0 (E6C400089).
Values previously written to this register was bogus.
Curiously earlyprintk works with the previous code.
* Remove duplicate initialisation of GPIO port 152, SCIFA0_TXD (0xE6053098).
This should have no effect other than to very slightly reduce the amount of
code.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into rmobile-latest
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be4461
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Include module.h header in apic_flat_64.c
x86, apic: Make apic drivers static
x86, apic: Clean up bigsmp apic selection code
x86, apic: Use .apicdrivers section for the apic drivers list
x86, apic: Introduce .apicdrivers section to find the list of apic drivers
x86, x2apic: Move the common bits to x2apic.h
x86, x2apic: Minimize IPI register writes using cluster groups
x86, x2apic: Track the x2apic cluster sibling map
x86, x2apic: Remove duplicate code for IPI mask routines
x86, apic: Use probe routines to simplify apic selection
x86, ioapic: Consolidate mp_ioapic_routing[] into 'struct ioapic'
x86, ioapic: Consolidate gsi routing info into 'struct ioapic'
x86, ioapic: Consolidate mp_ioapics[] into 'struct ioapic'
x86, ioapic: Consolidate ioapic_saved_data[] into 'struct ioapic'
x86, ioapic: Add struct ioapic
x86, ioapic: Remove duplicate code for saving/restoring RTEs
x86, ioapic: Use ioapic_saved_data while enabling intr-remapping
x86, ioapic: Allocate ioapic_saved_data early
x86, ioapic: Fix potential resume deadlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
|
|
apic_flat_64.c needs to include module.h because it uses
EXPORT_SYMBOL_GPL().
This fixes these warnings on some !SMP randconfigs:
arch/x86/kernel/apic/apic_flat_64.c:31: warning: data definition has no type or storage class
arch/x86/kernel/apic/apic_flat_64.c:31: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/x86/kernel/apic/apic_flat_64.c:31: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20110523104300.dd532a99.randy.dunlap@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/mach-ns9xxx/include/mach/uncompress.h
|
|
and 'spear' into for-linus
|
|
'consolidate-generic', 'consolidate-smp', 'consolidate-stmp' and 'consolidate-zones' into consolidate
|
|
bcmring has a set of four sp804 timers incorporated, yet it has its
own copy of the sp804 code. Convert its clockevent implementation
to the standard sp804 support code.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
bcmring has a set of four sp804 timers incorporated, yet it has its
own copy of the sp804 code. Convert its clocksource implementation
to the standard sp804 support code.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move adding clkdev table to init_early to make sure the common sp804 clockevents can be initialized properly.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This allows platforms to specify the rate of the SP804 clockevent via
the clk subsystem. While ARM boards clock these at 1MHz, BCMRing also
has SP804 timers but are clocked at different rates.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This allows platforms to specify the clcokevent name upon registration.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This allows platforms to specify the rate of the SP804 clocksource via
the clk subsystem. While ARM boards clock these at 1MHz, BCMRing also
has SP804 timers but are clocked at different rates.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This allows platforms to specify the clocksource name upon
registration, which is necessary should they wish to register more
than one sp804 clocksource.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the OMAP1 32-bit down counting clocksource to the generic
clocksource infrastructure.
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the MXS timrotv2 32-bit down counting clocksource to the
generic clocksource infrastructure.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert SPEAr platforms 16-bit up counting clocksource, which requires
a 16-bit register access read rather than 32-bit.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the Integrator/AP 16-bit down-counting clocksource to the
generic clocksource infrastructure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the W90x900 24-bit down-counting clocksource to the generic
mmio clocksource infrastructure
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert SP804, MXC, Nomadik and Orion 32-bit down-counting clocksources
to generic mmio clocksource infrastructure.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert ixp4xx, lpc32xx, mxc, netx, pxa, sa1100, tcc8k, tegra and u300
to use the generic mmio clocksource recently introduced.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update sa1100 clockevents code to reflect what its later derivative
does with clockevents_calc_mult_shift(). Use OSSR_M* constants too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The OMAP1 clocksource interrupt handler just increments a variable
which otherwise isn't used, so this seems to be unnecessary. Tony
Lindgren confirms, so lets remove it.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
s5p duplicates the runtime selection of the timer register three times.
Move this out into a separate function.
FIXME: It is unclear whether this code needs to support true runtime
selection of the timer register, or whether it can be selected once at
init time.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix sample size bit operations
perf tools: Fix ommitted mmap data update on remap
watchdog: Change the default timeout and configure nmi watchdog period based on watchdog_thresh
watchdog: Disable watchdog when thresh is zero
watchdog: Only disable/enable watchdog if neccessary
watchdog: Fix rounding bug in get_sample_period()
perf tools: Propagate event parse error handling
perf tools: Robustify dynamic sample content fetch
perf tools: Pre-check sample size before parsing
perf tools: Move evlist sample helpers to evlist area
perf tools: Remove junk code in mmap size handling
perf tools: Check we are able to read the event size on mmap
|
|
ARM build fails with the following symptom:
CC arch/arm/kernel/asm-offsets.s
In file included from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:57,
from arch/arm/kernel/asm-offsets.c:13:
include/linux/spinlock.h: In function 'spin_unlock_wait':
include/linux/spinlock.h:360: error: implicit declaration of function 'cpu_relax'
make[1]: *** [arch/arm/kernel/asm-offsets.s] Error 1
Fix it by including <asm/processor.h>.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
|
|
Commit e2a083dc0da9aa6437e14811198379b18cdfa7f8
"ARM: consolidate SMP cross call implementation" broke the ux500
compilation since the smp.h header declared a function called
from headsmp.S. This fixes it up by declaring it locally instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (346 commits)
ASoC: core: Don't set "(null)" as a driver name
ALSA: hda - Use LPIB for ATI/AMD chipsets as default
Revert "ALSA: hda - Use position_fix=3 as default for AMD chipsets"
ASoC: Tegra: Fix compile when debugfs not enabled
ASoC: spdif-dit: Add missing MODULE_*
SOUND: OSS: Remove Au1550 driver.
ALSA: hda - add Intel Panther Point HDMI codec id
ALSA: emu10k1 - Add dB range to Bass and Treble for SB Live!
ALSA: hda - Remove PCM mixer elements from Virtual Master of realtek
ALSA: hda - Fix input-src parse in patch_analog.c
ASoC: davinci-mcasp: enable ping-pong SRAM buffers
ASoC: add iPAQ hx4700 machine driver
ASoC: Asahi Kasei AK4641 codec driver
ALSA: hda - Enable Realtek ALC269 codec input layer beep
ALSA: intel8x0m: enable AMD8111 modem
ALSA: HDA: Add jack detection for HDMI
ALSA: sound, core, pcm_lib: fix xrun_log
ASoC: Max98095: Move existing NULL check before pointer dereference.
ALSA: sound, core, pcm_lib: xrun_log: log also in_interrupt
ALSA: usb-audio - Add support for USB X-Fi S51 Pro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Eliminate various 'set but not used' warnings
x86, SMEP: Fix section mismatch warnings
x86, amd: Use _safe() msr access for GartTlbWlk disable code
|
|
As a result of c42321c (genirq: Make generic irq chip depend on
CONFIG_GENERIC_IRQ_CHIP), we now need those platforms using this in
my tree to select this symbol.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'kvm-updates/2.6.40' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (131 commits)
KVM: MMU: Use ptep_user for cmpxchg_gpte()
KVM: Fix kvm mmu_notifier initialization order
KVM: Add documentation for KVM_CAP_NR_VCPUS
KVM: make guest mode entry to be rcu quiescent state
KVM: x86 emulator: Make jmp far emulation into a separate function
KVM: x86 emulator: Rename emulate_grpX() to em_grpX()
KVM: x86 emulator: Remove unused arg from emulate_pop()
KVM: x86 emulator: Remove unused arg from writeback()
KVM: x86 emulator: Remove unused arg from read_descriptor()
KVM: x86 emulator: Remove unused arg from seg_override()
KVM: Validate userspace_addr of memslot when registered
KVM: MMU: Clean up gpte reading with copy_from_user()
KVM: PPC: booke: add sregs support
KVM: PPC: booke: save/restore VRSAVE (a.k.a. USPRG0)
KVM: PPC: use ticks, not usecs, for exit timing
KVM: PPC: fix exit accounting for SPRs, tlbwe, tlbsx
KVM: PPC: e500: emulate SVR
KVM: VMX: Cache vmcs segment fields
KVM: x86 emulator: consolidate segment accessors
KVM: VMX: Avoid reading %rip unnecessarily when handling exceptions
...
|
|
on watchdog_thresh
Before the conversion of the NMI watchdog to perf event, the
watchdog timeout was 5 seconds. Now it is 60 seconds. For my
particular application, netbooks, 5 seconds was a better
timeout. With a short timeout, we catch faults earlier and are
able to send back a panic. With a 60 second timeout, the user is
unlikely to wait and will instead hit the power button, causing
us to lose the panic info.
This change configures the NMI period to watchdog_thresh and
sets the softlockup_thresh to watchdog_thresh * 2. In addition,
watchdog_thresh was reduced to 10 seconds as suggested by Ingo
Molnar.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1306127423-3347-4-git-send-email-msb@chromium.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071642.GF22305@elte.hu>
|
|
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (28 commits)
sparc32: fix build, fix missing cpu_relax declaration
SCHED_TTWU_QUEUE is not longer needed since sparc32 now implements IPI
sparc32,leon: Remove unnecessary page_address calls in LEON DMA API.
sparc: convert old cpumask API into new one
sparc32, sun4d: Implemented SMP IPIs support for SUN4D machines
sparc32, sun4m: Implemented SMP IPIs support for SUN4M machines
sparc32,leon: Implemented SMP IPIs for LEON CPU
sparc32: implement SMP IPIs using the generic functions
sparc32,leon: SMP power down implementation
sparc32,leon: added some SMP comments
sparc: add {read,write}*_be routines
sparc32,leon: don't rely on bootloader to mask IRQs
sparc32,leon: operate on boot-cpu IRQ controller registers
sparc32: always define boot_cpu_id
sparc32: removed unused code, implemented by generic code
sparc32: avoid build warning at mm/percpu.c:1647
sparc32: always register a PROM based early console
sparc32: probe for cpu info only during startup
sparc: consolidate show_cpuinfo in cpu.c
sparc32,leon: implement genirq CPU affinity
...
|
|
The setup_smep function gets calle at resume time too, and is thus not a
pure __init function. When marked as __init, it gets thrown out after
the kernel has initialized, and when the kernel is suspended and
resumed, the code will no longer be around, and we'll get a nice "kernel
tried to execute NX-protected page" oops because the page is no longer
marked executable.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
