| Age | Commit message (Collapse) | Author |
|---|
|
We can't cope with initrds outside of memory, so check that the
initrd is within some declared memory to the kernel before using
it. Otherwise we're likely to OOPS during boot.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://gitorious.org/linux-davinci/linux-davinci into fixes
|
|
|
|
Dump out the following 16-bit instruction to the faulting instruction
in the Code: line. This allows Thumb-2 instructions to be properly
encoded.
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If the page to cmpxchg is user mode read only (not write),
we should simulate a data abort first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit af3e4fd37a "ARM: 6859/1: Add writethrough dcache support for
ARM926EJS processor" broke Thumb2 compilation by omitting to maintain
the wide encoding for the added branch instructions which made the
ARM926EJ-S record smaller than expected, breaking the record walk code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If the DT physical address is zero, this is equivalent to no DT.
Especially when the actual RAM physical address is not located at zero,
the result of phys_to_virt() would point to la-la-land and crash the
kernel, which crash is completely silent this early during boot.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The IO accessors for U300 were using u32 rather than the nominal
void __iomem * type, rectify this by properly defining the
virtual base for statically mapped peripherals to be
void __iomem *. Requires fixing a field in struct clk as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 45b95235b0ac86cef2ad4480b0618b8778847479.
Will Deacon reports that:
In 52af9c6c ("ARM: 6943/1: mm: use TTBR1 instead of reserved context ID")
I updated the ASID rollover code to use only the kernel page tables
whilst updating the ASID.
Unfortunately, the code to restore the user page tables was part of a
later patch which isn't yet in mainline, so this leaves the code
quite broken.
We're also in the process of eliminating __ARCH_WANT_INTERRUPTS_ON_CTXSW
from ARM, so lets revert these until we can properly sort out what we're
doing with the context switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 52af9c6cd863fe37d1103035ec7ee22ac1296458.
Will Deacon reports that:
In 52af9c6c ("ARM: 6943/1: mm: use TTBR1 instead of reserved context ID")
I updated the ASID rollover code to use only the kernel page tables
whilst updating the ASID.
Unfortunately, the code to restore the user page tables was part of a
later patch which isn't yet in mainline, so this leaves the code
quite broken.
We're also in the process of eliminating __ARCH_WANT_INTERRUPTS_ON_CTXSW
from ARM, so lets revert these until we can properly sort out what we're
doing with the ARM context switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Make the PCM device structures used in devices.c
and devices-da8xx.c static as they are used only
in the respective files.
This was found when trying to build a single image
for DaVinci and DA8x devices using runtime P2V support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The code which does the chained handler setup was overwriting
chip_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Holger Hans Peter Freyther <holger@freyther.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This patch fixes the lockdep warning of "unannotated irqs-off"[1].
After entering __irq_usr, arm core will disable interrupt automatically,
but __irq_usr does not annotate the irq disable, so lockdep may complain
the warning if it has chance to check this in irq handler.
This patch adds trace_hardirqs_off in __irq_usr before entering irq_handler
to handle the irq, also calls ret_to_user_from_irq to avoid calling
disable_irq again.
This is also a fix for irq off tracer.
[1], lockdep warning log of "unannotated irqs-off"
[ 13.804687] ------------[ cut here ]------------
[ 13.809570] WARNING: at kernel/lockdep.c:3335 check_flags+0x78/0x1d0()
[ 13.816467] Modules linked in:
[ 13.819732] Backtrace:
[ 13.822357] [<c01cb42c>] (dump_backtrace+0x0/0x100) from [<c06abb14>] (dump_stack+0x20/0x24)
[ 13.831268] r6:c07d8c2c r5:00000d07 r4:00000000 r3:00000000
[ 13.837280] [<c06abaf4>] (dump_stack+0x0/0x24) from [<c01ffc04>] (warn_slowpath_common+0x5c/0x74)
[ 13.846649] [<c01ffba8>] (warn_slowpath_common+0x0/0x74) from [<c01ffc48>] (warn_slowpath_null+0x2c/0x34)
[ 13.856781] r8:00000000 r7:00000000 r6:c18b8194 r5:60000093 r4:ef182000
[ 13.863708] r3:00000009
[ 13.866485] [<c01ffc1c>] (warn_slowpath_null+0x0/0x34) from [<c0237d84>] (check_flags+0x78/0x1d0)
[ 13.875823] [<c0237d0c>] (check_flags+0x0/0x1d0) from [<c023afc8>] (lock_acquire+0x4c/0x150)
[ 13.884704] [<c023af7c>] (lock_acquire+0x0/0x150) from [<c06af638>] (_raw_spin_lock+0x4c/0x84)
[ 13.893798] [<c06af5ec>] (_raw_spin_lock+0x0/0x84) from [<c01f9a44>] (sched_ttwu_pending+0x58/0x8c)
[ 13.903320] r6:ef92d040 r5:00000003 r4:c18b8180
[ 13.908233] [<c01f99ec>] (sched_ttwu_pending+0x0/0x8c) from [<c01f9a90>] (scheduler_ipi+0x18/0x1c)
[ 13.917663] r6:ef183fb0 r5:00000003 r4:00000000 r3:00000001
[ 13.923645] [<c01f9a78>] (scheduler_ipi+0x0/0x1c) from [<c01bc458>] (do_IPI+0x9c/0xfc)
[ 13.932006] [<c01bc3bc>] (do_IPI+0x0/0xfc) from [<c06b0888>] (__irq_usr+0x48/0xe0)
[ 13.939971] Exception stack(0xef183fb0 to 0xef183ff8)
[ 13.945281] 3fa0: ffffffc3 0001500c 00000001 0001500c
[ 13.953948] 3fc0: 00000050 400b45f0 400d9000 00000000 00000001 400d9600 6474e552 bea05b3c
[ 13.962585] 3fe0: 400d96c0 bea059c0 400b6574 400b65d8 20000010 ffffffff
[ 13.969573] r6:00000403 r5:fa240100 r4:ffffffff r3:20000010
[ 13.975585] ---[ end trace efc4896ab0fb62cb ]---
[ 13.980468] possible reason: unannotated irqs-off.
[ 13.985534] irq event stamp: 1610
[ 13.989044] hardirqs last enabled at (1610): [<c01c703c>] no_work_pending+0x8/0x2c
[ 13.997131] hardirqs last disabled at (1609): [<c01c7024>] ret_slow_syscall+0xc/0x1c
[ 14.005371] softirqs last enabled at (0): [<c01fe5e4>] copy_process+0x2cc/0xa24
[ 14.013183] softirqs last disabled at (0): [< (null)>] (null)
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The "Virtual memory kernel layout" message at startup already prints
.text and .data. Print .bss too.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as these do. In binutils 2.21 these are treated
as fatal errors.
The issue in proc-arm7tdmi.S was also fixed independently by Peter
Chubb.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The introduction of the mmio timer accidentally referenced the
old clocksource struct which does not exist anymore. Fix this by
using a simple string instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 7ff550de99141cbd3be0129d563cc4554fdde9f6 breaks vexpress booting. The
v2m clock table needs to be setup in init_early before the timer
initialization occurs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Check the MX51 chip revision in run-time so that the correct SDMA firmware can
be loaded.
While at it also remove the silicon revision from the sdma_script_start_addrs
structure name for MX51. All the MX51 revisions share the same SDMA start addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
I get this build error as of today:
arch/arm/mach-mxs/ocotp.c: In function 'mxs_get_ocotp':
arch/arm/mach-mxs/ocotp.c:54: error: implicit declaration of function 'cpu_relax'
make[2]: *** [arch/arm/mach-mxs/ocotp.o] Error 1
Looks like it has been indirectly included before which broke now.
Include it directly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
ARM: Tegra: Harmony: Fix conflicting GPIO numbering
|
|
Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.
To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.
This fixes a regression introduced by commit
6f168f2fa60f87e85e0df25e87e2372f22f5eb7c.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: strncpy: fix handling of zero lengths
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: add DMAC clock definitions on SH7372
ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
sh_mobile_meram: MERAM platform data for LCDC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
dmaengine: shdma: Fix up fallout from runtime PM changes.
Revert "clocksource: sh_cmt: Runtime PM support"
Revert "clocksource: sh_tmu: Runtime PM support"
sh: Fix up asm-generic/ptrace.h fallout.
sh64: Move from P1SEG to CAC_ADDR for consistent sync.
sh64: asm/pgtable.h needs asm/mmu.h
sh: asm/tlb.h needs linux/swap.h
sh: mark DMA slave ID 0 as invalid
sh: Update shmin to reflect PIO dependency.
sh: arch/sh/kernel/process_32.c needs linux/prefetch.h.
sh: add MMCIF runtime PM support on ecovec
sh: switch ap325rxa to dynamically manage the platform camera
|
|
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio_net: delay TX callbacks
virtio: add api for delayed callbacks
virtio_test: support event index
vhost: support event index
virtio_ring: support event idx feature
virtio ring: inline function to check for events
virtio: event index interface
virtio: add full three-clause BSD text to headers.
virtio balloon: kill tell-host-first logic
virtio console: don't manually set or finalize VIRTIO_CONSOLE_F_MULTIPORT.
drivers, block: virtio_blk: Replace cryptic number with the macro
virtio_blk: allow re-reading config space at runtime
lguest: remove support for VIRTIO_F_NOTIFY_ON_EMPTY.
lguest: fix up compilation after move
lguest: fix timer interrupt setup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] wire up sendmmsg() syscall for Itanium
|
|
Add entries in unistd.h and entry.S to make this new syscall visible.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix mwait_play_dead() faulting on mwait-incapable cpus
x86 idle: Fix mwait deprecation warning message
Evil merge to remove extra quote noticed by Joe Perches
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Put back -pg to tsc.o and add no GCOV to vread_tsc_64.o
|
|
The Apple custom PIC only exist in some earlier machine models,
anything with an MPIC will crash on suspend if we register those
syscore ops unconditionally.
This is a regression caused by commit f5a592f7d74e ("PM / PowerPC: Use
struct syscore_ops instead of sysdevs for PM")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was an ordering issue with regards to instruction_pointer() being
used in profile_pc() prior to the asm-generic/ptrace.h include, which
subsequently provided the instruction_pointer() definition. In the
interest of simplicity we simply open-code the regs->pc deref for the
profile_pc() definition instead.
The FP functions were also broken due to a lack of a common regs->fp,
so provide a common GET_FP() that is safe for both architectures in order
to fix up the frame pointer helpers too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
sh64 doesn't define a P1SEGADDR, resulting in a build failure. The proper
mapping can be attained for both sh32 and 64 via the CAC_ADDR macro, so
switch to that instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Needed to satisfy the __in_29bit_mode() check.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Commit 1e56a56410bb64bce62d44563e35a143fc2d515f introduced the mmu_gather
rework for sh, but missed a linux/swap.h include:
CC arch/sh/mm/tlb-urb.o
In file included from arch/sh/mm/tlb-urb.c:14:0:
arch/sh/include/asm/tlb.h: In function '__tlb_remove_page':
arch/sh/include/asm/tlb.h:92:2: error: implicit declaration of function 'free_page_and_swap_cache'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh-fixes-for-linus
|
|
A logic error in mwait_play_dead() causes the kernel to use
mwait even on cpus which don't support it, such as KVM virtual
cpus.
Introduced by:
349c004e3d31: x86: A fast way to check capabilities of the current cpu
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=36222
Reported-by: Török Edwin <edwintorok@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1306758237-9327-1-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix:
arch/x86/kernel/process.c:645:1: warning: unknown escape sequence '\i'
due to missing escape backslash, introduced by this commit:
5d4c47e0195b: x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1306748286-24701-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Without an IRQ chip set, we now get a WARN_ON and no timer interrupt. This
prevents booting.
Fortunately, the fix is a one-liner: set up the timer IRQ like everything
else.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .39.x
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] mm: fix mmu_gather rework
[S390] mm: fix storage key handling
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: more /proc and /sys file support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
x86 idle: deprecate "no-hlt" cmdline param
x86 idle APM: deprecate CONFIG_APM_CPU_IDLE
x86 idle floppy: deprecate disable_hlt()
x86 idle: EXPORT_SYMBOL(default_idle, pm_idle) only when APM demands it
x86 idle: clarify AMD erratum 400 workaround
idle governor: Avoid lock acquisition to read pm_qos before entering idle
cpuidle: menu: fixed wrapping timers at 4.294 seconds
|
|
Quite a few functions that get called from the tlb gather code require that
preemption must be disabled. So disable preemption inside of the called
functions instead.
The only drawback is that rcu_table_freelist_finish() doesn't get necessarily
called on the cpu(s) that filled the free lists. So we may see a delay, until
we finally see an rcu callback. However over time this shouldn't matter.
So we get rid of lots of "BUG: using smp_processor_id() in preemptible"
messages.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
page_get_storage_key() and page_set_storage_key() expect a page address
and not its page frame number. This got inconsistent with 2d42552d
"[S390] merge page_test_dirty and page_clear_dirty".
Result is that we read/write storage keys from random pages and do not
have a working dirty bit tracking at all.
E.g. SetPageUpdate() doesn't clear the dirty bit of requested pages, which
for example ext4 doesn't like very much and panics after a while.
Unable to handle kernel paging request at virtual user address (null)
Oops: 0004 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 1 Not tainted 2.6.39-07551-g139f37f-dirty #152
Process flush-94:0 (pid: 1576, task: 000000003eb34538, ksp: 000000003c287b70)
Krnl PSW : 0704c00180000000 0000000000316b12 (jbd2_journal_file_inode+0x10e/0x138)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000000000 0000000000000000 0000000000000000 0700000000000000
0000000000316a62 000000003eb34cd0 0000000000000025 000000003c287b88
0000000000000001 000000003c287a70 000000003f1ec678 000000003f1ec000
0000000000000000 000000003e66ec00 0000000000316a62 000000003c287988
Krnl Code: 0000000000316b04: f0a0000407f4 srp 4(11,%r0),2036,0
0000000000316b0a: b9020022 ltgr %r2,%r2
0000000000316b0e: a7740015 brc 7,316b38
>0000000000316b12: e3d0c0000024 stg %r13,0(%r12)
0000000000316b18: 4120c010 la %r2,16(%r12)
0000000000316b1c: 4130d060 la %r3,96(%r13)
0000000000316b20: e340d0600004 lg %r4,96(%r13)
0000000000316b26: c0e50002b567 brasl %r14,36d5f4
Call Trace:
([<0000000000316a62>] jbd2_journal_file_inode+0x5e/0x138)
[<00000000002da13c>] mpage_da_map_and_submit+0x2e8/0x42c
[<00000000002daac2>] ext4_da_writepages+0x2da/0x504
[<00000000002597e8>] writeback_single_inode+0xf8/0x268
[<0000000000259f06>] writeback_sb_inodes+0xd2/0x18c
[<000000000025a700>] writeback_inodes_wb+0x80/0x168
[<000000000025aa92>] wb_writeback+0x2aa/0x324
[<000000000025abde>] wb_do_writeback+0xd2/0x274
[<000000000025ae3a>] bdi_writeback_thread+0xba/0x1c4
[<00000000001737be>] kthread+0xa6/0xb0
[<000000000056c1da>] kernel_thread_starter+0x6/0xc
[<000000000056c1d4>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000000000316a8a>] jbd2_journal_file_inode+0x86/0x138
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT on SMP hardware that supports it.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI uses only mwait_idle_with_hints(), and never uses mwait_idle().
Deprecate mwait_idle() and the "idle=mwait" cmdline param
to simplify the x86 idle code.
After this change, kernels configured with
(!CONFIG_ACPI=n && !CONFIG_INTEL_IDLE=n) when run on hardware
that support MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be used.
cc: x86@kernel.org
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
We'd rather that modern machines not check if HLT works on
every entry into idle, for the benefit of machines that had
marginal electricals 15-years ago. If those machines are still running
the upstream kernel, they can use "idle=poll". The only difference
will be that they'll now invoke HLT in machine_hlt().
cc: x86@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
We don't want to export the pm_idle function pointer to modules.
Currently CONFIG_APM_CPU_IDLE w/ CONFIG_APM_MODULE forces us to.
CONFIG_APM_CPU_IDLE is of dubious value, it runs only on 32-bit
uniprocessor laptops that are over 10 years old. It calls into
the BIOS during idle, and is known to cause a number of machines
to fail.
Removing CONFIG_APM_CPU_IDLE and will allow us to stop exporting
pm_idle. Any systems that were calling into the APM BIOS
at run-time will simply use HLT instead.
cc: x86@kernel.org
cc: Jiri Kosina <jkosina@suse.cz>
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
In the long run, we don't want default_idle() or (pm_idle)() to
be exported outside of process.c. Start by not exporting them
to modules, unless the APM build demands it.
cc: x86@kernel.org
cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The workaround for AMD erratum 400 uses the term "c1e" falsely suggesting:
1. Intel C1E is somehow involved
2. All AMD processors with C1E are involved
Use the string "amd_c1e" instead of simply "c1e" to clarify that
this workaround is specific to AMD's version of C1E.
Use the string "e400" to clarify that the workaround is specific
to AMD processors with Erratum 400.
This patch is text-substitution only, with no functional change.
cc: x86@kernel.org
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
