| Age | Commit message (Collapse) | Author |
|---|
|
This switches integrator platforms to use the consolidated CLCD
panel support, including the display capabilities. These capabilities
prevent the unsupported BGR565 mode being selected, while still
allowing RGB5551, BGR5551 and RGB565 modes.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This consolidates the CLCD panel definitions and memory allocation into
one location.
Rename the Sanyo 2.5in and Epson 2.2in displays after their respective
part numbers. Rather than using a general "Sanyo 2.5in" and "Epson
2.2in" description of the display panel, use the manufacturers part
number to be more specific. This helps people identify what the timings
actually refer to, which are panel specific.
While here, add CLCD capability information to each panel definition,
which has no effect until we add the board-level capabilities.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When the CLCD is in anything but RGB888 mode, its outputs are configured
for RGB5551 output. Integrator/CP supports RGB565 via an external
multiplexer, which we configure for RGB5551 or RGB565 based only on the
bits per pixel. So when userspace asks for the RGB555 layout, the mux
remains in RGB565 mode, and we produce incorrect colours. Fix this.
Note that Integrator doesn't support BGR565 mode, but does support
BGR5551.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
RGB565 with blue in the LSB wasn't supported. Add support for this
layout.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The compactflash device on this platform is not usable simply because it
is never registered with the kernel. Fix that up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix two section mismatch warnings in the platform SMP bringup code for
Realview and Versatile Express:
WARNING: arch/arm/mach-realview/built-in.o(.text+0x8ac): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
WARNING: arch/arm/mach-vexpress/built-in.o(.text+0x7b4): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
x86,percpu: Move out of place 64 bit ops into X86_64 section
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
um: Use generic irq Kconfig
tile: Use generic irq Kconfig
sparc: Use generic irq Kconfig
score: Use generic irq Kconfig
powerpc: Use generic irq Kconfig
parisc: Use generic irq Kconfig
mn10300: Use generic irq Kconfig
microblaze: Use generic irq Kconfig
m68knommu: Use generic irq Kconfig
ia64: Use generic irq Kconfig
frv: Use generic irq Kconfig
blackfin: Use generic irq Kconfig
alpha: Use generic irq Kconfig
genirq: Remove __do_IRQ
m32r: Convert to generic irq Kconfig
m32r: Convert usrv platform irq handling
m32r: Convert opsput_lcdpld irq chip
m32r: Convert opsput lanpld irq chip
m32r: Convert opsput pld irq chip
m32r: Convert opsput irq chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: p2m: correctly initialize partial p2m leaf
xen: fix non-ANSI function warning in irq.c
|
|
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/83xx: fix build failures on dt compatible list.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc/mpic: Fix mask/unmask timeout message
powerpc/pseries: Add BNX2=m to defconfig
powerpc: Enable 64kB pages and 1024 threads in pseries config
powerpc: Disable mcount tracers in pseries defconfig
powerpc/boot/dts: Install dts from the right directory
powerpc: machine_check_generic is wrong on 64bit
powerpc: Check RTAS extended log flag before checking length
powerpc: Fix corruption when grabbing FWNMI data
powerpc: Rework pseries machine check handler
powerpc: Don't silently handle machine checks from userspace
powerpc: Remove duplicate debugger hook in machine_check_exception
powerpc: Never halt RTAS error logging after receiving an unrecoverable machine check
powerpc: Don't force MSR_RI in machine_check_exception
powerpc: Print 32 bits of DSISR in show_regs
powerpc/kdump: Disable ftrace during kexec
powerpc/kdump: Move crash_kexec_stop_spus to kdump crash handler
powerpc/kexec: Remove empty ppc_md.machine_kexec_prepare
powerpc/kexec: Don't initialise kexec hooks to default handlers
powerpc/kdump: Remove ppc_md.machine_crash_shutdown
powerpc/kexec: Remove ppc_md.machine_kexec
...
|
|
After changing the p2m mapping to a tree by
commit 58e05027b530ff081ecea68e38de8d59db8f87e0
xen: convert p2m to a 3 level tree
and trying to boot a DomU with 615MB of memory, the following crash was
observed in the dump:
kernel direct mapping tables up to 26f00000 @ 1ec4000-1fff000
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c0107397>] xen_set_pte+0x27/0x60
*pdpt = 0000000000000000 *pde = 0000000000000000
Adding further debug statements showed that when trying to set up
pfn=0x26700 the returned mapping was invalid.
pfn=0x266ff calling set_pte(0xc1fe77f8, 0x6b3003)
pfn=0x26700 calling set_pte(0xc1fe7800, 0x3)
Although the last_pfn obtained from the startup info is 0x26700, which
should in turn not be hit, the additional 8MB which are added as extra
memory normally seem to be ok. This lead to looking into the initial
p2m tree construction, which uses the smaller value and assuming that
there is other code handling the extra memory.
When the p2m tree is set up, the leaves are directly pointed to the
array which the domain builder set up. But if the mapping is not on a
boundary that fits into one p2m page, this will result in the last leaf
being only partially valid. And as the invalid entries are not
initialized in that case, things go badly wrong.
I am trying to fix that by checking whether the current leaf is a
complete map and if not, allocate a completely new page and copy only
the valid pointers there. This may not be the most efficient or elegant
solution, but at least it seems to allow me booting DomUs with memory
assignments all over the range.
BugLink: http://bugs.launchpad.net/bugs/686692
[v2: Redid a bit of commit wording and fixed a compile warning]
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Dike <jdike@addtoit.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "David S. Miller" <davem@davemloft.net>
|
|
No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Howells <dhowells@redhat.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Howells <dhowells@redhat.com>
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
|
|
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
|
|
Use the generic irq Kconfig. Select GENERIC_HARDIRQS_NO_DEPRECATED as
we have converted all irq_chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chip to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
The irq descriptors are already initialized by the generic
code. Remove the redundant init code and set the irq chip with the
proper accessor function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
|
|
Use the generic irq Kconfig. Select GENERIC_HARDIRQS_NO_DEPRECATED as
we have converted all irq_chip functions. Fix the fallout in
show_interrupts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
|
|
Convert the irq chip functions and install handle_simple_irq for each
interrupt to get rid of __do_IRQ()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
|
|
Convert the irq_chip functions and install handle_simple_irq for each
interrupt. This converts V10 to the flow handling and lets us remove
__do_IRQ().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
|
|
Use the wrapper around __do_IRQ() so we can convert V10 and V32
seperately.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
|
|
Switch to the generic irq Kconfig. h8300 has all irq chips converted
to the new functions, so select the GENERIC_HARDIRQS_NO_DEPRECATED
switch as well. Fixup the resulting fallout in show_interrupts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
|
