| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the device tree node for SSS module
found on Exynos5420 and Exynos5250
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Now that the SPI controllers are disabled by default for Exynos5250
there is no need to explicitly disable them in individual board files.
This hunk appears not to have been merged when doing the original
conversion, add it now.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch use ADC to get the temperature of SoC/battery by using NTC thermistor
driver in hwmon. NTC thermistor driver covnvert ADC's raw data to temperature
by using following variables:
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch move common dt data of interrupt combiner controller to
exynos4x12.dtsi. Each Exynos4x12 SoC has different number of interrput combiner
as following:
- Exynos4212 : interrput combiner 18(0 ~ 17)
- Exynos4412 : interrput combiner 20(0 ~ 19)
The exynos combiner driver initialize interrupt according to specific number
of interrput combiner.
- samsung,combiner-nr : The number of interrput combiners supported.
Also,
This patch arrange again the dt data according to register address
in exynos4212/exynos4412.dtsi.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch add GPS_ALIVE power domain for Exynos4x12 SoC. GPS_ALIVE power domain
include GPS_BLK for GPS IP. Exynos SoC used generic power-domain driver to
control power domain. After completed kernel booting, Exynos power-domain driver
disable un-used power domain to reduce power-consumption/leak.
If GPS_ALIVE power domain isn't registered to Exynos power-domain driver,
happen power-leakage because GPS_ALIVE_CONFIGURATION is default power on state.
- 0x10023D00 : GPS_ALIVE_CONFIGURATION register address
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
ARM CPU has its own performance profiling unit(PMU, Perforamnce Monitoring Unit).
This patch add PMU dt data to support PMU which count cache hit and miss events.
PMU interrput list of Exynos4212
- <2 2> : INTG2[2] - PMUIRQ[0] for CPU0
- <3 2> : INTG3[2] - PMUIRQ[1] for CPU1
PMU interrput list of Exynos4412
- <2 2> : INTG2[2], PMUIRQ[0] for CPU0
- <3 2> : INTG3[2], PMUIRQ[1] for CPU1
- <18 2> : INTG18[2], PMUIRQ[2] : CPU2
- <19 2> : INTG19[2], PMUIRQ[3] : CPU3
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch add ADC(Analog to Digital Converter)'s dt data to get raw data
with IIO subsystem. Usually, ADC is used to check temperature, jack type
and so on.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The patch replaces magic numbers with macros defined in DT header
in exynos5440 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The patch replaces magic numbers with macros defined in DT header
in exynos5420 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The patch replaces magic numbers with macros defined in DT header
in exynos5250 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The patch replaces magic numbers with macros defined in DT header
in exynos4 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
LDO10 is directly connected to MMC controller. Register this
through vmmc-supply property.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Added GPIO based wake up key to Arndale octa board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Fixed voltage regulators required by audio codec added.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add Maxim 77686 PMIC node for EXYNOS5250 based SMDK5250 board.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
To allow EXYNOS4412 based Odroidx and Origen-quad boards to operate between
200MHz to 1.4Ghz, update the vdd_arm voltage range to operate between these
cpu clock speeds.
Cc: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In EXYNOS5 series SoCs, PMU has registers to enable/disable mask/unmask
watchdog timer which is not the case with s3c series SoCs so, there is a
need to have different compatible names for watchdog to handle these pmu
registers access.
Hence this patch removes watchdog node from Exynos5.dtsi common file and
make it separate by updating existing node in Exynos5250 and adding new node
to Exynos5420. This patch also makes the watchdog node enabled by default
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds pmusysreg node to exynos5250 and exynos5420 dtsi files to
handle PMU register accesses in a centralized way using syscon driver
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This commit:
f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
|
|
With commit d8d14bd09cdd ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.
Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC DT Fixes for v3.14
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1cb1cea5 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
* tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:
warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
Instead enable TI EDMA support from defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
SMP is a user configurable option, not a hardware feature and should not
be selected.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.
Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.
Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:
* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.
The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 78d1632183454dba46ca8295484a5e7603acdc18 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).
Restore the static map on the Integrator/CP.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The same workaround as ff999b8a0983ee15668394ed49e38d3568fc6859
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pyll ARM64 patches from Catalin Marinas:
- Build fix with DMA_CMA enabled
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Introduce PTE_WRITE
arm64: mm: Remove PTE_BIT_FUNC macro
arm64: FIQs are unused
arm64: mm: fix the function name in comment of cpu_do_switch_mm
arm64: fix build error if DMA_CMA is enabled
arm64: kernel: fix per-cpu offset restore on resume
arm64: mm: fix the function name in comment of __flush_dcache_area
arm64: mm: use ubfm for dcache_line_size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"A pair of changes for alpha. One fixes a networking regression, and
the second adds audit syscall support which will help in supporting
systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix broken network checksum
alpha: Enable system-call auditing support.
|
