| Age | Commit message (Collapse) | Author |
|---|
|
As IP22 is now using do_IRQ for timer interrupt, don't mess with
interrupt handler any longer
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix some typo introduced on clockevent conversion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Some processors offer the option of using the interrupt on which
normally the count / compare interrupt would be signaled as a normal
interupt pin. Previously this required some ugly hackery for each
system which is much easier done by a quick and simple probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Userland, including the C library and the dynamic linker, is keen to use
the SYNC instruction, even for "generic" MIPS I binaries these days.
Which makes it less than useful on MIPS I processors.
This change adds the emulation, but as our do_ri() infrastructure was not
really prepared to take yet another instruction, I have rewritten it and
its callees slightly as follows.
Now there is only a single place a possible signal is thrown from. The
place is at the end of do_ri(). The instruction word is fetched in
do_ri() and passed down to handlers. The handlers are called in sequence
and return a result that lets the caller decide upon further processing.
If the result is positive, then the handler has picked the instruction,
but a signal should be thrown and the result is the signal number. If the
result is zero, then the handler has successfully simulated the
instruction. If the result is negative, then the handler did not handle
the instruction; to make it more obvious the calls do not follow the usual
0/-Exxx result convention they now return -1 instead of -EFAULT.
The calculation of the return EPC is now at the beginning. The reason is
it is easier to handle it there as emulation callees may modify a register
and an instruction may be located in delay slot of a branch whose result
depends on the register. It has to be undone if a signal is to be raised,
but it is not a problem as this is the slow-path case, and both actions
are done in single places now rather than the former being scattered
through emulation handlers.
The part of do_cpu() being covered follows the changes to do_ri().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x478): Section mismatch: reference to .init.text:start_kernel (between '_stext' and 'run_init_process')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[SCSI] Remove full sg table memset()
[SCSI] ide-scsi: remove usage of sg_last()
Fix loop terminating conditions in fill_sg().
[BLOCK] Clear sg entry before filling in blk_rq_map_sg()
IA64: iommu uses sg_next with an invalid sg element
cciss: disable DMA refetch on Smart Array P600
swiotlb: fix map_sg failure handling
SPARC64: fix iommu sg chaining
[SCSI] ide-scsi: use scsi_sg_count() instead of ->use_sg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (24 commits)
[POWERPC] Fix vmemmap warning in init_64.c
[POWERPC] Fix 64 bits vDSO DWARF info for CR register
[POWERPC] Add 1TB workaround for PA6T
[POWERPC] Enable NO_HZ and high res timers for pseries and ppc64 configs
[POWERPC] Quieten cache information at boot
[POWERPC] Quieten clockevent printk
[POWERPC] Enable SLUB in *_defconfig
[POWERPC] Fix 1TB segment detection
[POWERPC] Fix iSeries_hpte_insert prototype
[POWERPC] Fix copyright symbol
[POWERPC] ibmebus: Move to of_device and of_platform_driver, match eHCA and eHEA drivers
[POWERPC] ibmebus: Add device creation and bus probing based on of_device
[POWERPC] ibmebus: Remove bus match/probe/remove functions
[POWERPC] Move of_device allocation into of_device.[ch]
[POWERPC] mpc52xx: device tree changes for FEC and MDIO
[POWERPC] bestcomm: GenBD task support
[POWERPC] bestcomm: FEC task support
[POWERPC] bestcomm: ATA task support
[POWERPC] bestcomm: core bestcomm support for Freescale MPC5200
[POWERPC] mpc52xx: Update mpc52xx_psc structure with B revision changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
Remove magic macros for screen_info structure members
[x86] remove uses of magic macros for boot_params access
|
|
Fix typos in CONFIG_RELOCATABLE. Use tab + 2 spaces for indentation on all
lines.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Bernhard Walle <bwalle@suse.de>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace some SPIN_LOCK_UNLOCKED with DEFINE_SPINLOCK
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the old-fashioned lk201 driver under drivers/tc/ that used to be
used by the old dz.c and zs.c drivers, which is now orphan code referred to
from nowhere and does not build anymore. A modern replacement is available
as drivers/input/keyboard/lkkbd.c.
There are no plans to do anything about this piece of code and it does not
fit anywhere anymore, so it is not just a matter of maintenance or the lack
of. There are still some bits that might be added to the new lkkbd.c
driver based on the old code, and the embedded hardware documentation which
is otherwise quite hard to get hold of might be useful to keep too. Both
of these can be done separately though. RIP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
dma_cache_(wback|inv|wback_inv) were the earliest attempt on a generalized
cache managment API for I/O purposes. Originally it was basically the raw
MIPS low level cache API exported to the entire world. The API has
suffered from a lack of documentation, was not very widely used unlike it's
more modern brothers and can easily be replaced by dma_cache_sync. So
remove it rsp. turn the surviving bits back into an arch private API, as
discussed on linux-arch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a prefix "VMCOREINFO_" to the vmcoreinfo macros. Old vmcoreinfo macros
were defined as generic names SYMBOL/SIZE/OFFSET /LENGTH/CONFIG, and it is
impossible to grep for them. So these names should be changed. This
discussion is the following:
http://www.ussg.iu.edu/hypermail/linux/kernel/0709.1/0415.html
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch set frees the restriction that makedumpfile users should install a
vmlinux file (including the debugging information) into each system.
makedumpfile command is the dump filtering feature for kdump. It creates a
small dumpfile by filtering unnecessary pages for the analysis. To
distinguish unnecessary pages, it needs a vmlinux file including the debugging
information. These days, the debugging package becomes a huge file, and it is
hard to install it into each system.
To solve the problem, kdump developers discussed it at lkml and kexec-ml. As
the result, we reached the conclusion that necessary information for dump
filtering (called "vmcoreinfo") should be embedded into the first kernel file
and it should be accessed through /proc/vmcore during the second kernel.
(http://www.uwsg.iu.edu/hypermail/linux/kernel/0707.0/1806.html)
Dan Aloni created the patch set for the above implementation.
(http://www.uwsg.iu.edu/hypermail/linux/kernel/0707.1/1053.html)
And I updated it for multi architectures and memory models.
(http://lists.infradead.org/pipermail/kexec/2007-August/000479.html)
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This makes powerpc64's compat code use the new linux/elfcore-compat.h,
reducing some hand-copied duplication.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For some time /proc/sys/kernel/core_pattern has been able to set its output
destination as a pipe, allowing a user space helper to receive and
intellegently process a core. This infrastructure however has some
shortcommings which can be enhanced. Specifically:
1) The coredump code in the kernel should ignore RLIMIT_CORE limitation
when core_pattern is a pipe, since file system resources are not being
consumed in this case, unless the user application wishes to save the core,
at which point the app is restricted by usual file system limits and
restrictions.
2) The core_pattern code should be able to parse and pass options to the
user space helper as an argv array. The real core limit of the uid of the
crashing proces should also be passable to the user space helper (since it
is overridden to zero when called).
3) Some miscellaneous bugs need to be cleaned up (specifically the
recognition of a recursive core dump, should the user mode helper itself
crash. Also, the core dump code in the kernel should not wait for the user
mode helper to exit, since the same context is responsible for writing to
the pipe, and a read of the pipe by the user mode helper will result in a
deadlock.
This patch:
Remove the check of RLIMIT_CORE if core_pattern is a pipe. In the event that
core_pattern is a pipe, the entire core will be fed to the user mode helper.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: <martin.pitt@ubuntu.com>
Cc: <wwoods@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Driver for the CompactFlash slot on the PA Semi Electra eval board. It's
a simple device sitting on localbus, with interrupts and detect/voltage
control over GPIO.
The driver is implemented as an of_platform driver, and adds localbus
as a bus being probed by the of_platform framework.
[akpm@linux-foundation.org: cleanups]
[olof@lixom.net: fix build]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It makes more sense to make instrumentation support experimental on a
case-by-case basis.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove the rmb() from mce_log(), since the immunized version of
rcu_dereference() makes it unnecessary.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
list_del() hardly can fail, so checking for return value is pointless
(and current code always return 0).
Nobody really cared that return value anyway.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch single-linked binfmt formats list to usual list_head's. This leads
to one-liners in register_binfmt() and unregister_binfmt(). The downside
is one pointer more in struct linux_binfmt. This is not a problem, since
the set of registered binfmts on typical box is very small -- (ELF +
something distro enabled for you).
Test-booted, played with executable .txt files, modprobe/rmmod binfmt_misc.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the OOM killer's extern function prototypes to include/linux/oom.h and
include it where necessary.
[clg@fr.ibm.com: build fix]
Cc: Andrea Arcangeli <andrea@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update dump_task_altivec() (which has so far never been put to use) so that
it dumps the Altivec/VMX registers (VR[0] - VR[31], VSCR and VRSAVE) in the
same format as the ptrace get_vrregs(), and add the appropriate glue
typedef and #defines to make it work.
A new note type of NT_PPC_VMX was chosen to be 0x100 (arbitrarily) because
it allows the low range values to be used for more generic purposes and
0x100 seems an adequate starting point for PowerPC extensions.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace NT_PRXFPREG with ELF_CORE_XFPREG_TYPE in the coredump code which
allows for more flexibility in the note type for the state of 'extended
floating point' implementations in coredumps. New note types can now be
added with an appropriate #define.
This does #define ELF_CORE_XFPREG_TYPE to be NT_PRXFPREG in all
current users so there's are no change in behaviour.
This will let us use different note types on powerpc for the Altivec/VMX
state that some PowerPC cpus have (G4, PPC970, POWER6) and for the SPE
(signal processing extension) state that some embedded PowerPC cpus from
Freescale have.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
into merge
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge
|
|
Use the right printk format to silence the following warning.
CC arch/powerpc/mm/init_64.o
arch/powerpc/mm/init_64.c: In function 'vmemmap_populate':
arch/powerpc/mm/init_64.c:243: warning: format '%p' expects type 'void *', but argument 4 has type 'long unsigned int'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The current DWARF info for CR are incorrect, causing the gcc unwinder to
go to lunch if we take a segfault in the vdso. This fixes it.
Problem identified by Andrew Haley, and fix provided by Jakub Jelinek
(thanks !).
Unfortunately, a bug in gcc cause it to not quite work either, but that
is being fixed separately with something around the lines of:
linux-unwind.h:
fs->regs.reg[R_CR2].loc.offset = (long) ®s->ccr - new_cfa;
+ /* CR? regs are just 32-bit and PPC is big-endian. */
+ fs->regs.reg[R_CR2].loc.offset += sizeof (long) - 4;
(According to Jakub)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
PA6T has a bug where the slbie instruction does not honor the large
segment bit. As a result, we have to always use slbia when switching
context.
We don't have to worry about changing the slbie's during fault processing,
since they should never be replacing one VSID with another using the
same ESID. I.e. there's no risk for inserting duplicate entries due to a
failed slbie of the old entry. So as long as we clear it out on context
switch we should be fine.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Enable NO_HZ and high res timers for the ppc64 and pseries defconfigs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
After 6 years the ppc64 kernel still thinks its important to tell me my
cache line size is 0x80 bytes. I think most people who care know that by
now. The rest probably cant even understand the hex output.
Since we might have misconfigured firmware or cpus that have a linesize
that isnt 128 bytes, I still print it out for those cases. If people
would prefer to remove it completely, lets do it.
Also for lpar remove the htab_address printout since its not used.
Anton
ppc64 boot log usability expert
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The clockevent bootup message only needs to be KERN_INFO.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
When checking out the new NO_HZ support in powerpc, I noticed we never
slept for more than 2 seconds. It turns out SLAB has a 2 second per cpu
timer that causes this.
After switching to SLUB I see some nice 4 second sleeps which is the
limit on this POWER6 box (the decrementer ticks at 512MHz):
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 3.96 sec
slept 3.80 sec
slept 2.99 sec
Since SLUB is now the default and some powerpc defconfigs already enable
it, lets enable SLUB across the board for consistency. While doing this
I also noticed that the maple defconfig has SLAB debugging enabled which
is sure to make your box nice and slow. Fix that too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Buglet in the 1TB detection makes it return after checking the first
property word, even if it's not a match.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Commit 1189be6508d45183013ddb82b18f4934193de274 ([POWERPC] Use 1TB
segments) added an argument to hpte_insert.
Also make iSeries_hpte_insert static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
It seems to have been munged by patchwork.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
eHEA drivers
Replace struct ibmebus_dev and struct ibmebus_driver with struct of_device
and struct of_platform_driver, respectively. Match the external ibmebus
interface and drivers using it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The devtree root is now searched for devices matching a built-in whitelist
during boot, so these devices appear on the bus from the beginning. It is
still possible to manually add/remove devices to/from the bus by using the
probe/remove sysfs interface. Also, when a device driver registers itself,
the devtree is matched against its matchlist.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Remove old code that will be replaced by rewritten and shorter functions in
the next patch. Keep struct ibmebus_dev and struct ibmebus_driver for now,
but replace ibmebus_{,un}register_driver() by dummy functions. This way, the
kernel will still compile and run during the transition and git bisect will
be happy.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Extract generic of_device allocation code from of_platform_device_create()
and move it into of_device.[ch], called of_device_alloc(). Also, there's now
of_device_free() which puts the device node.
This way, bus drivers that build on of_platform (like ibmebus will) can
build upon this code instead of reinventing the wheel.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
sg list elements might not be continuous.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Commit 2c941a204070ab32d92d40318a3196a7fb994c00 looks incomplete. The
helper functions like prepare_sg() need to support sg chaining too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
