| Age | Commit message (Collapse) | Author |
|---|
|
for it"
This reverts commit 3e1a878b7ccdb31da6d9d2b855c72ad87afeba3f.
It came in very late, and already has one reported failure: Sitsofe
reports that the current tree fails to boot on his EeePC, and bisected
it down to this. Rather than waste time trying to figure out what's
wrong, just revert it.
Reported-by: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 7d453eee36ae ("x86/efi: Wire up CONFIG_EFI_MIXED") introduced a
regression for the functionality to load kernels above 4G. The relevant
(incorrect) reasoning behind this change can be seen in the commit
message,
"The xloadflags field in the bzImage header is also updated to reflect
that the kernel supports both entry points by setting both of
XLF_EFI_HANDOVER_32 and XLF_EFI_HANDOVER_64 when CONFIG_EFI_MIXED=y.
XLF_CAN_BE_LOADED_ABOVE_4G is disabled so that the kernel text is
guaranteed to be addressable with 32-bits."
This is obviously bogus since 32-bit EFI loaders will never place the
kernel above the 4G mark. So this restriction is entirely unnecessary.
But things are worse than that - since we want to encourage people to
always compile with CONFIG_EFI_MIXED=y so that their kernels work out of
the box for both 32-bit and 64-bit firmware, commit 7d453eee36ae
effectively disables XLF_CAN_BE_LOADED_ABOVE_4G completely.
Remove the overzealous and superfluous restriction and restore the
XLF_CAN_BE_LOADED_ABOVE_4G functionality.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1402140380-15377-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
* Fix earlyprintk=efi,keep support by switching to an ioremap() mapping
of the framebuffer when early_ioremap() is no longer available and
dropping __init from functions that may be invoked after
free_initmem() - Dave Young
* We shouldn't be exporting the EFI runtime map in sysfs if not using
the new 1:1 EFI mapping code since in that case the mappings are not
static across a kexec reboot - Dave Young
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Hang is observed on virtual machines during CPU hotplug,
especially in big guests with many CPUs. (It reproducible
more often if host is over-committed).
It happens because master CPU gives up waiting on
secondary CPU and allows it to run wild. As result
AP causes locking or crashing system. For example
as described here:
https://lkml.org/lkml/2014/3/6/257
If master CPU have sent STARTUP IPI successfully,
and AP signalled to master CPU that it's ready
to start initialization, make master CPU wait
indefinitely till AP is onlined.
To ensure that AP won't ever run wild, make it
wait at early startup till master CPU confirms its
intention to wait for AP. If AP doesn't respond in 10
seconds, the master CPU will timeout and cancel
AP onlining.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1401975765-22328-4-git-send-email-imammedo@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If system is running without debug level logging,
it will not log error if do_boot_cpu() failed to
wakeup AP. It may lead to silent AP bringup
failures at boot time.
Change message level to KERN_ERR to make error
visible to user as it's done on other architectures.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1401975765-22328-3-git-send-email-imammedo@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
currently if AP wake up is failed, master CPU marks AP as not
present in do_boot_cpu() by calling set_cpu_present(cpu, false).
That leads to following list corruption on the next physical CPU
hotplug:
[ 418.107336] WARNING: CPU: 1 PID: 45 at lib/list_debug.c:33 __list_add+0xbe/0xd0()
[ 418.115268] list_add corruption. prev->next should be next (ffff88003dc57600), but was ffff88003e20c3a0. (prev=ffff88003e20c3a0).
[ 418.123693] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT ipt_REJECT cfg80211 xt_conntrack rfkill ee
[ 418.138979] CPU: 1 PID: 45 Comm: kworker/u10:1 Not tainted 3.14.0-rc6+ #387
[ 418.149989] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
[ 418.165750] Workqueue: kacpi_hotplug acpi_hotplug_work_fn
[ 418.166433] 0000000000000021 ffff880038ca7988 ffffffff8159b22d 0000000000000021
[ 418.176460] ffff880038ca79d8 ffff880038ca79c8 ffffffff8106942c ffff880038ca79e8
[ 418.177453] ffff88003e20c3a0 ffff88003dc57600 ffff88003e20c3a0 00000000ffffffea
[ 418.178445] Call Trace:
[ 418.185811] [<ffffffff8159b22d>] dump_stack+0x49/0x5c
[ 418.186440] [<ffffffff8106942c>] warn_slowpath_common+0x8c/0xc0
[ 418.187192] [<ffffffff81069516>] warn_slowpath_fmt+0x46/0x50
[ 418.191231] [<ffffffff8136ef51>] ? acpi_ns_get_node+0xb7/0xc7
[ 418.193889] [<ffffffff812f796e>] __list_add+0xbe/0xd0
[ 418.196649] [<ffffffff812e2aa9>] kobject_add_internal+0x79/0x200
[ 418.208610] [<ffffffff812e2e18>] kobject_add_varg+0x38/0x60
[ 418.213831] [<ffffffff812e2ef4>] kobject_add+0x44/0x70
[ 418.229961] [<ffffffff813e2c60>] device_add+0xd0/0x550
[ 418.234991] [<ffffffff813f0e95>] ? pm_runtime_init+0xe5/0xf0
[ 418.250226] [<ffffffff813e32be>] device_register+0x1e/0x30
[ 418.255296] [<ffffffff813e82a3>] register_cpu+0xe3/0x130
[ 418.266539] [<ffffffff81592be5>] arch_register_cpu+0x65/0x150
[ 418.285845] [<ffffffff81355c0d>] acpi_processor_hotadd_init+0x5a/0x9b
...
Which is caused by the fact that generic_processor_info() allocates
logical CPU id by calling:
cpu = cpumask_next_zero(-1, cpu_present_mask);
which returns id of previously failed to wake up CPU, since its
bit is cleared by do_boot_cpu() and as result register_cpu()
tries to register another CPU with the same id as already
present but failed to be onlined CPU.
Taking in account that AP will not do anything if master CPU
failed to wake it up, there is no reason to mark that AP as not
present and break next cpu hotplug attempts. As a side effect of
not marking AP as not present, user would be allowed to online
it again later.
Also fix memory corruption in acpi_unmap_lsapic()
if during CPU hotplug master CPU failed to wake up AP
it set percpu x86_cpu_to_apicid to BAD_APICID=0xFFFF for AP.
However following attempt to unplug that CPU will lead to
out of bound write access to __apicid_to_node[] which is
32768 items long on x86_64 kernel.
So with above fix of cpu_present_mask make sure that a present
CPU has a valid APIC ID by not setting x86_cpu_to_apicid
to BAD_APICID in do_boot_cpu() on failure and allow
acpi_processor_remove()->acpi_unmap_lsapic() cleanly remove CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1401975765-22328-2-git-send-email-imammedo@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
check_irq_vectors_for_cpu_disable() can overestimate the number of
available interrupt vectors, so the check for cpu down succeeds, but
the actual cpu removal fails.
It iterates from FIRST_EXTERNAL_VECTOR to NR_VECTORS, which is wrong
because the systems vectors are not taken into account.
Limit the search to first_system_vector instead of NR_VECTORS.
The second indicator for vector availability the used_vectors bitmap
is not taken into account at all. So system vectors,
e.g. IA32_SYSCALL_VECTOR (0x80) and IRQ_MOVE_CLEANUP_VECTOR (0x20),
are accounted as available.
Add a check for the used_vectors bitmap and do not account vectors
which are marked there.
[ tglx: Simplified code. Rewrote changelog and code comments. ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Steven Rostedt (Red Hat) <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Elliott, Robert (Server Storage)" <Elliott@hp.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/1400160305-17774-2-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Peter Anvin:
"A single quite small patch that managed to get overlooked earlier, to
prevent a user space triggerable oops on systems without HPET"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Fix an OOPS accessing the HPET mapping w/o an HPET
|
|
For ioremapped efi memory aka old_map the virt addresses are not persistant
across kexec reboot. kexec-tools will read the runtime maps from sysfs then
pass them to 2nd kernel and assuming kexec efi boot is ok. This will cause
kexec boot failure.
To address this issue do not export runtime maps in case efi old_map so
userspace can use no efi boot instead.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fix from Ben Herrenschmidt:
"Here's just one trivial patch to wire up sys_renameat2 which I seem to
have completely missed so far.
(My test build scripts fwd me warnings but miss the ones generated for
missing syscalls)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Wire renameat2() syscall
|
|
Pull MIPS fixes from Ralf Baechle:
"A fair number of fixes across the field. Nothing terribly
complicated; the one liners in below changelog should be fairly
descriptive.
Noteworthy is the SB1 change which the result of changes to binutils
resulting in one big gas warning for most files being assembled as
well as the asid_cache and branch emulation fixes which fix corruption
or possible uninteded behaviour of kernel or application code. The
remainder of fixes are more platforms or subsystem specific"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: R46000: Fix Micro-assembler field overflow for R4600 V2
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
MIPS: Lemote 2F: cs5536: mfgpt: use raw locks
MIPS: SB1: Fix excessive kernel warnings.
MIPS: RC32434: fix broken PCI resource initialization
MIPS: malta: memory.c: Initialize the 'memsize' variable
MIPS: Fix typo when reporting cache and ftlb errors for ImgTec cores
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
MIPS: Fix branch emulation of branch likely instructions.
MIPS: Fix a typo error in AUDIT_ARCH definition
MIPS: Change type of asid_cache to unsigned long
|
|
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
While I play inhouse patches with much memory pressure on qemu-kvm,
3.14 kernel was randomly crashed. The reason was kernel stack overflow.
When I investigated the problem, the callstack was a little bit deeper
by involve with reclaim functions but not direct reclaim path.
I tried to diet stack size of some functions related with alloc/reclaim
so did a hundred of byte but overflow was't disappeard so that I encounter
overflow by another deeper callstack on reclaim/allocator path.
Of course, we might sweep every sites we have found for reducing
stack usage but I'm not sure how long it saves the world(surely,
lots of developer start to add nice features which will use stack
agains) and if we consider another more complex feature in I/O layer
and/or reclaim path, it might be better to increase stack size(
meanwhile, stack usage on 64bit machine was doubled compared to 32bit
while it have sticked to 8K. Hmm, it's not a fair to me and arm64
already expaned to 16K. )
So, my stupid idea is just let's expand stack size and keep an eye
toward stack consumption on each kernel functions via stacktrace of ftrace.
For example, we can have a bar like that each funcion shouldn't exceed 200K
and emit the warning when some function consumes more in runtime.
Of course, it could make false positive but at least, it could make a
chance to think over it.
I guess this topic was discussed several time so there might be
strong reason not to increase kernel stack size on x86_64, for me not
knowing so Ccing x86_64 maintainers, other MM guys and virtio
maintainers.
Here's an example call trace using up the kernel stack:
Depth Size Location (51 entries)
----- ---- --------
0) 7696 16 lookup_address
1) 7680 16 _lookup_address_cpa.isra.3
2) 7664 24 __change_page_attr_set_clr
3) 7640 392 kernel_map_pages
4) 7248 256 get_page_from_freelist
5) 6992 352 __alloc_pages_nodemask
6) 6640 8 alloc_pages_current
7) 6632 168 new_slab
8) 6464 8 __slab_alloc
9) 6456 80 __kmalloc
10) 6376 376 vring_add_indirect
11) 6000 144 virtqueue_add_sgs
12) 5856 288 __virtblk_add_req
13) 5568 96 virtio_queue_rq
14) 5472 128 __blk_mq_run_hw_queue
15) 5344 16 blk_mq_run_hw_queue
16) 5328 96 blk_mq_insert_requests
17) 5232 112 blk_mq_flush_plug_list
18) 5120 112 blk_flush_plug_list
19) 5008 64 io_schedule_timeout
20) 4944 128 mempool_alloc
21) 4816 96 bio_alloc_bioset
22) 4720 48 get_swap_bio
23) 4672 160 __swap_writepage
24) 4512 32 swap_writepage
25) 4480 320 shrink_page_list
26) 4160 208 shrink_inactive_list
27) 3952 304 shrink_lruvec
28) 3648 80 shrink_zone
29) 3568 128 do_try_to_free_pages
30) 3440 208 try_to_free_pages
31) 3232 352 __alloc_pages_nodemask
32) 2880 8 alloc_pages_current
33) 2872 200 __page_cache_alloc
34) 2672 80 find_or_create_page
35) 2592 80 ext4_mb_load_buddy
36) 2512 176 ext4_mb_regular_allocator
37) 2336 128 ext4_mb_new_blocks
38) 2208 256 ext4_ext_map_blocks
39) 1952 160 ext4_map_blocks
40) 1792 384 ext4_writepages
41) 1408 16 do_writepages
42) 1392 96 __writeback_single_inode
43) 1296 176 writeback_sb_inodes
44) 1120 80 __writeback_inodes_wb
45) 1040 160 wb_writeback
46) 880 208 bdi_writeback_workfn
47) 672 144 process_one_work
48) 528 112 worker_thread
49) 416 240 kthread
50) 176 176 ret_from_fork
[ Note: the problem is exacerbated by certain gcc versions that seem to
generate much bigger stack frames due to apparently bad coalescing of
temporaries and generating too many spills. Rusty saw gcc-4.6.4 using
35% more stack on the virtio path than 4.8.2 does, for example.
Minchan not only uses such a bad gcc version (4.6.3 in his case), but
some of the stack use is due to debugging (CONFIG_DEBUG_PAGEALLOC is
what causes that kernel_map_pages() frame, for example). But we're
clearly getting too close.
The VM code also seems to have excessive stack frames partly for the
same compiler reason, triggered by excessive inlining and lots of
function arguments.
We need to improve on our stack use, but in the meantime let's do this
simple stack increase too. Unlike most earlier reports, there is
nothing simple that stands out as being really horribly wrong here,
apart from the fact that the stack frames are just bigger than they
should need to be. - Linus ]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S Tsirkin <mst@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: PJ Waskiewicz <pjwaskiewicz@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"The usual random collection of relatively small ARM fixes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8063/1: bL_switcher: fix individual online status reporting of removed CPUs
ARM: 8064/1: fix v7-M signal return
ARM: 8057/1: amba: Add Qualcomm vendor ID.
ARM: 8052/1: unwind: Fix handling of "Pop r4-r[4+nnn],r14" opcode
ARM: 8051/1: put_user: fix possible data corruption in put_user
ARM: 8048/1: fix v7-M setup stack location
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix CoW regression for transparent hugepages by routing set_pmd_at to
set_pte_at, which correctly handles PTE_WRITE and will mark the
resulting table entry as read-only where appropriate"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix pmd_write CoW brokenness
|
|
Commit 9c7e535fcc17 ("arm64: mm: Route pmd thp functions through pte
equivalents") changed the pmd manipulator and accessor functions to
convert the target pmd to a pte, process it with the pte functions, then
convert it back. Along the way, we gained support for PTE_WRITE, however
this is completely ignored by set_pmd_at, and so we fail to set the
PMD_SECT_RDONLY for PMDs, resulting in all sorts of lovely failures (like
CoW not working).
Partially reverting the offending commit (by making use of
PMD_SECT_RDONLY explicitly for pmd_{write,wrprotect,mkwrite} functions)
leads to further issues because pmd_write can then return potentially
incorrect values for page table entries marked as RDONLY, leading to
BUG_ON(pmd_write(entry)) tripping under some THP workloads.
This patch fixes the issue by routing set_pmd_at through set_pte_at,
which correctly takes the PTE_WRITE flag into account. Given that
THP mappings are always anonymous, the additional cache-flushing code
in __sync_icache_dcache won't impose any significant overhead as the
flush will be skipped.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The content of /sys/devices/system/cpu/cpu*/online is still 1 for those
CPUs that the switcher has removed even though the global state in
/sys/devices/system/cpu/online is updated correctly.
It turns out that commit 0902a9044f ("Driver core: Use generic
offline/online for CPU offline/online") has changed the way those files
retrieve their content by relying on on the generic attribute handling
code. The switcher, by calling cpu_down() directly, bypasses this
handling and the attribute value doesn't get updated.
Fix this by calling device_offline()/device_online() instead.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull kvm fixes from Paolo Bonzini:
"Small fixes for x86, slightly larger fixes for PPC, and a forgotten
s390 patch. The PPC fixes are important because they fix breakage
that is new in 3.15"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: announce irqfd capability
KVM: x86: disable master clock if TSC is reset during suspend
KVM: vmx: disable APIC virtualization in nested guests
KVM guest: Make pv trampoline code executable
KVM: PPC: Book3S: ifdef on CONFIG_KVM_BOOK3S_32_HANDLER for 32bit
KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit
KVM: PPC: Book3S: HV: make _PAGE_NUMA take effect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull two powerpc fixes from Ben Herrenschmidt:
"Here's a pair of powerpc fixes for 3.15 which are also going to
stable.
One's a fix for building with newer binutils (the problem currently
only affects the BookE kernels but the affected macro might come back
into use on BookS platforms at any time). Unfortunately, the binutils
maintainer did a backward incompatible change to a construct that we
use so we have to add Makefile check.
The other one is a fix for CPUs getting stuck in kexec when running
single threaded. Since we routinely use kexec on power (including in
our newer bootloaders), I deemed that important enough"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc, kexec: Fix "Processor X is stuck" issue during kexec from ST mode
powerpc: Fix 64 bit builds with binutils 2.24
|
|
Fix uasm warning, which triggered because of workaround for R4600 V2 CPUs.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
ptrace_{get,set}_watch_regs access current_cpu_data to get the watch
register count/masks, which calls smp_processor_id(). However they are
run in preemptible context and therefore trigger warnings like so:
[ 6340.092000] BUG: using smp_processor_id() in preemptible [00000000] code: gdb/367
[ 6340.092000] caller is ptrace_get_watch_regs+0x44/0x220
Since the watch register count/masks should be the same across all
CPUs, use boot_cpu_data instead. Note that this may need to change in
future should a heterogenous system be supported where the count/masks
are not the same across all CPUs (the current code is also incorrect
for this scenario - current_cpu_data here would not necessarily be
correct for the CPU that the target task will execute on).
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6879/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The lock is taken in the raw irq path and therefore a rawlock should be
used instead of a normal spinlock.
While here I drop the export symbol on that variable since there are no
other users.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Hua Yan <yanh@lemote.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6936/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A kernel build with binutils 2.24 is going to emit warnings like
CC kernel/sys.o
{standard input}: Assembler messages:
{standard input}:701: Warning: the 32-bit MIPS architecture does not support the `mdmx' extension
{standard input}:701: Warning: the `mdmx' extension requires 64-bit FPRs
{standard input}:701: Warning: the `mips3d' extension requires MIPS32 revision 2 or greater
{standard input}:701: Warning: the `mips3d' extension requires 64-bit FPRs
for almost every file. This is caused by changes to gas' interpretation
of .set semantics. Fixed by explicitly disabling MIPS3D and MDMX for
Sibyte builds.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba963 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With binutils 2.24, various 64 bit builds fail with relocation errors
such as
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_base_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_end_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
The assembler maintainer says:
I changed the ABI, something that had to be done but unfortunately
happens to break the booke kernel code. When building up a 64-bit
value with lis, ori, shl, oris, ori or similar sequences, you now
should use @high and @higha in place of @h and @ha. @h and @ha
(and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA)
now report overflow if the value is out of 32-bit signed range.
ie. @h and @ha assume you're building a 32-bit value. This is needed
to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h
and @toc@ha expressions, and for consistency I did the same for all
other @h and @ha relocs.
Replacing @h with @high in one strategic location fixes the relocation
errors. This has to be done conditionally since the assembler either
supports @h or @high but not both.
Cc: <stable@vger.kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes than we'd like at this point in the
release. Hopefully our very last batch before 3.15:
OMAP:
- Fix boot regression with CPU_IDLE enabled
- Fixes for audio playback on OMAP5
- Clock rate setting fix for OMAP3
- Misc idle/PM fixes
Exynos:
- Removal of a couple of power domains to work around issues with
access when they are powered down
- Enabling missing highspeed-i2c driver to make MMC regulators work
- Secondary CPU spin-up fix for 4212
- Remove MDMA1 engine to avoid conflicts on secure mode platforms
- A few other DT fixes
Marvell:
- PCI-e fixes for clocks and resource allocation
plus a few other smaller fixes, add a MAINTAINERS entry for reset
drivers, etc"
* tag 'fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
MAINTAINERS: Add reset controller framework entry
ARM: trusted_foundations: fix compile error on non-SMP
ARM: at91: sam9260: fix compilation issues
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
ARM: imx: fix error handling in ipu device registration
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: dts: Keep LDO4 always ON for exynos5250-arndale board
ARM: dts: Fix SPI interrupt numbers for exynos5420
ARM: dts: fix incorrect ak8975 compatible for exynos4412-trats2 board
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: mvebu: mvebu-soc-id: keep clock enabled if PCIe unit is enabled
ARM: mvebu: mvebu-soc-id: add missing clk_put() call
ARM: at91/dt: sam9260: correct external trigger value
...
|
|
The parent field of the 'rc32434_res_pci_mem1' resource points to
the resource itself which is obviously wrong. Due to the broken
initialitazion, the PCI devices on the Mikrotik RB532 boards are
not working since commit 22283178 (MIPS: avoid possible resource
conflict in register_pci_controller).
Remove the field initialization to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reported-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Cc: Gabor Juhos <juhosg@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/6940/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
According to the ARM ARM, the behaviour is UNPREDICTABLE if the PC read
from the exception return stack is not half word aligned. See the
pseudo code for ExceptionReturn() and PopStack().
The signal handler's address has the bit 0 set, and setup_return()
directly writes this to regs->ARM_pc. Current hardware happens to
discard this bit, but QEMU's emulation doesn't and this makes processes
crash. Mask out bit 0 before the exception return in order to get
predictable behaviour.
Fixes: 19c4d593f0b4 ("ARM: ARMv7-M: Add support for exception handling")
Cc: stable@kernel.org
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The arm EABI states that unwind opcode 10100nnn means pop register r4-4[4+nnn],aditionally there is a similar unwind opcode: 10101nnn which means the same thing plus popping r14. Those two cases are handled by the unwind_exec_pop_r4_to_rN function which checks whether the 4th bit is set and does r14 popping.
However, up until now it has been checking whether the 8th bit was set (mask & 0x80) instead of the 4th (mask & 0x8), a simple to make typo but this meant that we were always popping r14 even if we had the former opcode.
This patch changes the mask so that the 2 unwind opcodes are being handled correctly.
Signed-off-by: Nikolay Borisov <Nikolay.Borisov@arm.com>
Reviewed-by: Anurag Aggarwal <anurag19aggarwal@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
According to arm procedure call standart r2 register is call-cloberred.
So after the result of x expression was put into r2 any following
function call in p may overwrite r2. To fix this, the result of p
expression must be saved to the temporary variable before the
assigment x expression to __r2.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
__v7m_setup_stack currently sits in the .proc.info.init section, and
thus creates a bogus proc info entry (which by the way matches any
unknown CPU IDs, due to the entry's mask being 0). Move it out of
there.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If the 'memsize' environmental variable is not set by the bootloader
the 'memsize' variable is not initialized, leading to potential memory
problems. This patch fixes the problem by setting the initial
value to '0' to force the kernel to set a good default memory size.
Cc: <stable@vger.kernel.org> # v3.15+
Reported-by: Matheus Almeida <Matheus.Almeida@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6984/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Introduced by the following two commits:
75b5b5e0a262790fa11043fe45700499c7e3d818
"MIPS: Add support for FTLBs"
6de20451857ed14a4eecc28d08f6de5925d1cf96
"MIPS: Add printing of ES bit for Imgtec cores when cache error occurs"
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reported-by: Matheus Almeida <Matheus.Almeida@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org # v3.14+
Patchwork: https://patchwork.linux-mips.org/patch/6980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Originally, __NR_O32_Linux_syscalls, __NR_N32_Linux_syscalls and
__NR_64_Linux_syscalls have the same values as __NR_Linux_syscalls in
corresponding ABIs. But after commit 367f0b50e502d (MIPS: Wire up
renameat2 syscall) they are not the same. I think this is incorrect and
need a fix.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6987/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull sparc fixes from David Miller:
"A small bunch of bug fixes, in particular:
1) On older cpus we need a different chunk of virtual address space
to map the huge page TSB.
2) Missing memory barrier in Niagara2 memcpy.
3) trinity showed some places where fault validation was
unnecessarily loud on sparc64
4) Some sysfs printf's need a type adjustment, from Toralf Förster"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix format string mismatch in arch/sparc/kernel/sysfs.c
sparc64: Add membar to Niagara2 memcpy code.
sparc64: Fix huge TSB mapping on pre-UltraSPARC-III cpus.
sparc64: Don't bark so loudly about 32-bit tasks generating 64-bit fault addresses.
|
|
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Samsung-fixes-2 for 3.15
- keep LD04 always on for exynos5250-arndale
- fix spi interrupt numbers for exynos5420
- fix ak8975 compatible for exynos4412-trats2
* tag 'samsung-fixes-2nd-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Keep LDO4 always ON for exynos5250-arndale board
ARM: dts: Fix SPI interrupt numbers for exynos5420
ARM: dts: fix incorrect ak8975 compatible for exynos4412-trats2 board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The setup_max_cpus variable is only defined if CONFIG_SMP is set. Add
a preprocessor condition to avoid the following compilation error if
CONFIG_SMP is not set:
arch/arm/include/asm/trusted_foundations.h: In function 'register_trusted_foundations':
arch/arm/include/asm/trusted_foundations.h:57:2: error: 'setup_max_cpus' undeclared (first use in this function)
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest changes are fixes for races that kept triggering Trinity
crashes, plus liblockdep build fixes and smaller misc fixes.
The liblockdep bits in perf/urgent are a pull mistake - they should
have been in locking/urgent - but by the time I noticed other commits
were added and testing was done :-/ Sorry about that"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race between ring_buffer_detach() and ring_buffer_attach()
perf: Prevent false warning in perf_swevent_add
perf: Limit perf_event_attr::sample_period to 63 bits
tools/liblockdep: Remove all build files when doing make clean
tools/liblockdep: Build liblockdep from tools/Makefile
perf/x86/intel: Fix Silvermont's event constraints
perf: Fix perf_event_init_context()
perf: Fix race in removing an event
|
|
The 'renameat2()' system call was incorrectly added as a ENTRY_COMP() in
the parisc system call table by commit 18e480aa07f78 ("parisc: add
renameat2 syscall"). That causes a link-time error due to there not
being any compat version of that system call:
arch/parisc/kernel/built-in.o: In function `sys_call_table':
(.rodata+0xad0): undefined reference to `compat_sys_renameat2'
make: *** [vmlinux] Error 1
Easily fixed by marking the system call as being the same for compat as
for native by using ENTRY_SAME() instead of ENTRY_COMP().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Second 3.15 fixes for AT91
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
* tag 'at91-fixes2' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9260: fix compilation issues
ARM: at91/dt: sam9260: correct external trigger value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mvebu fixes for v3.15 (incremental #2)
- Armada 38x
- fix PCIe dt nodes for handling more interfaces
- mvebu
- mvebu-soc-id: fix clock handling and PCIe interface disabling.
* tag 'mvebu-fixes-3.15-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
ARM: mvebu: mvebu-soc-id: keep clock enabled if PCIe unit is enabled
ARM: mvebu: mvebu-soc-id: add missing clk_put() call
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two issues:
o For beql_op, beql_op, bne_op, bnel_op, blez_op, blezl_op, bgtz_op and
bgtzl_op the wrong field was being checked for the instruction opcode.
o For blez_op / blezl_op and bgtz_op / bgtzl_op the test was testing
for the wrong opcode.
This bug got introduced by d8d4e3ae0b5c179c0bfd3f0af5b352d13bea9cfa [MIPS
Kprobes: Refactor branch emulation].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Victor Kamensky <kamensky@cisco.com>
|
|
Use the hexadecimal values for the triggers to match what is done for the device
tree. This also fixes compilation issues as the defines have been moved
elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
|
|
Due a copy/paste error, the 'reg' values for the third PCIe interface
on Armada 380, and the third and fourth PCIe interfaces on Armada 385
are wrong: they are equal to the one of the second PCIe interface.
This patch fixes this by using the appropriate 'reg' values for those
PCIe interfaces.
Without this fix, the third and fourth PCIe interfaces are unusable on
those platforms.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400597008-4148-1-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 0d3d96ab0059 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs")
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes for v3.15-rc cycle" from Tony Lindgren:
Regression fixes for omaps for NAND, DMA, cpu_idle and audio.
Also a minor one line fix for audio clock on 54xx.
* tag 'omap-for-v3.15/fixes-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP3: clock: Back-propagate rate change from cam_mclk to dpll4_m5 on all OMAP3 platforms
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If we fail to allocate struct platform_device pdev we
dereference it after the goto label err.
This bug was found using coccinelle.
Fixes: afa77ef (ARM: mx3: dynamically allocate "ipu-core" devices)
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Samsung fixes for 3.15 from Kukjin Kim:
- Remove g2d_pd and mau_pd nodes on exynos5420.
Since the power domains are linked to the CMU blocks,
kernel panic happens during access clocks when the
power domains are disabled. Now this is a best solution.
- Enable HS-I2C on exynos5 by default
MMC partition cannot be mounted for RFS without the
enabling HS-I2C because regulators for MMC power are
connected to HS-I2C bus.
- Disable MDMA1 node on exynos5420
When MDMA1 runs in secure mode it makes kernel fault,
so need to disalbe it on exynos5420 by default instead
of each board.
- Fix the secondary CPU boot for exynos4212
* tag 'samsung-fixes' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The oops can be triggered in qemu using -no-hpet (but not nohpet) by
running a 32-bit program and reading a couple of pages before the vdso.
This should send SIGBUS instead of OOPSing.
The bug was introduced by:
commit 7a59ed415f5b57469e22e41fc4188d5399e0b194
Author: Stefani Seibold <stefani@seibold.net>
Date: Mon Mar 17 23:22:09 2014 +0100
x86, vdso: Add 32 bit VDSO time support for 32 bit kernel
which is new in 3.15.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/e99025d887d6670b6c4d81e6ccfeeb83770b21e9.1400109621.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
