| Age | Commit message (Collapse) | Author |
|---|
|
Fix some typos in the DNS-323 support code.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Stefan Agner found his board comes with 0x00b480/0x02 but the main
board also has Rev B printed on it like my 0x00b480/0x03. Some light
enum renaming was needed but it was to be expected.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
All the pieces were ready, just matter of assembling
them together.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The RTC and the two XOR engines are internal to the chip, and therefore
always available since they don't depend on a particular board layout.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
ts78xx add NAND support via plat_nand
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
|
|
amend RTC registering to not depend on ifdef's
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
|
|
Added checks to the platform_device_(register|add) calls so that if
a device failed to load it would then not later be unloaded; also
added the hooks so that it would not try to unload when the RTC
driver support is compiled out.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
|
|
The A0 revision of the mv78xx0 development board has four ethernet
ports, with PHY IDs 8-11, whereas the Z0 version has two, with PHY
addresses 8-9. This patch configures the third and fourth ethernet
port to use the PHY addresses on the A0 board to enable use of those
ports -- if we are running on a Z0 board, the ge10/11 setup code in
common.c will force these back to PHYless mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
On pre-A0 revisions of the mv78xx0 SoC, the third and fourth
ethernet interface are not brought out to pins, but are internally
cross-connected, so if we run on pre-A0 silicon, we'll force eth2
and eth3 to PHYless mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
During boot, identify which chip stepping we're running on (determined
by looking at the first PCIe unit's device ID and revision registers),
and print a message with the details about what we found.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
This allows for board support code to set up their MPP config if the
bootloader didn't do it all or did it wrong. This also allows to
register usable GPIOs.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Especially on Kirkwood, a couple GPIOs are actually only output capable.
Let's separate the ability to configure a GPIO as input or output to
accommodate this restriction.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5405/1: ep93xx: remove unused gesbc9312.h header
[ARM] 5404/1: Fix condition in arm_elf_read_implies_exec() to set READ_IMPLIES_EXEC
[ARM] omap: fix clock reparenting in omap2_clk_set_parent()
[ARM] 5403/1: pxa25x_ep_fifo_flush() *ep->reg_udccs always set to 0
[ARM] 5402/1: fix a case of wrap-around in sanity_check_meminfo()
[ARM] 5401/1: Orion: fix edge triggered GPIO interrupt support
[ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
[ARM] 5391/1: AT91: Enable GPIO clocks earlier
[ARM] 5390/1: AT91: Watchdog fixes
[ARM] 5398/1: Add Wan ZongShun to MAINTAINERS for W90P910
[ARM] omap: fix _omap2_clksel_get_src_field()
[ARM] omap: fix omap2_divisor_to_clksel() error return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: fix ifdef for 64bit thermal apic vector clear on shutdown
x86, mce: use force_sig_info to kill process in machine check
x86, mce: reinitialize per cpu features on resume
x86, rcu: fix strange load average and ksoftirqd behavior
|
|
Remove the gesbc9312.h header since it is unused.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
READ_IMPLIES_EXEC
READ_IMPLIES_EXEC must be set when:
o binary _is_ an executable stack (i.e. not EXSTACK_DISABLE_X)
o processor architecture is _under_ ARMv6 (XN bit is supported from ARMv6)
Signed-off-by: Makito SHIOKAWA <lkhmkt@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
commit aa5e97ce4bbc9d5daeec16b1d15bb3f6b7b4f4d4
[PATCH] improve precision of process accounting.
Introduced a timing regression:
-bash-3.2# time ls
real 0m0.006s
user 0m1.754s
sys 0m1.094s
The problem was introduced by an error in cputime_to_timeval.
Cputime is now 1/4096 microsecond, therefore, we have to divide
the remainder with 4096 to get the microseconds.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When changing the parent of a clock, it is necessary to keep the
clock use counts balanced otherwise things the parent state will
get corrupted. Since we already disable and re-enable the clock,
we might as well use the recursive versions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In the non highmem case, if two memory banks of 1GB each are provided,
the second bank would evade suppression since its virtual base would
be 0. Fix this by disallowing any memory bank which virtual base
address is found to be lower than PAGE_OFFSET.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now, early_pfn_in_nid(PFN, NID) may returns false if PFN is a hole.
and memmap initialization was not done. This was a trouble for
sparc boot.
To fix this, the PFN should be initialized and marked as PG_reserved.
This patch changes early_pfn_in_nid() return true if PFN is a hole.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
What's happening is that the assertion in mm/page_alloc.c:move_freepages()
is triggering:
BUG_ON(page_zone(start_page) != page_zone(end_page));
Once I knew this is what was happening, I added some annotations:
if (unlikely(page_zone(start_page) != page_zone(end_page))) {
printk(KERN_ERR "move_freepages: Bogus zones: "
"start_page[%p] end_page[%p] zone[%p]\n",
start_page, end_page, zone);
printk(KERN_ERR "move_freepages: "
"start_zone[%p] end_zone[%p]\n",
page_zone(start_page), page_zone(end_page));
printk(KERN_ERR "move_freepages: "
"start_pfn[0x%lx] end_pfn[0x%lx]\n",
page_to_pfn(start_page), page_to_pfn(end_page));
printk(KERN_ERR "move_freepages: "
"start_nid[%d] end_nid[%d]\n",
page_to_nid(start_page), page_to_nid(end_page));
...
And here's what I got:
move_freepages: Bogus zones: start_page[2207d0000] end_page[2207dffc0] zone[fffff8103effcb00]
move_freepages: start_zone[fffff8103effcb00] end_zone[fffff8003fffeb00]
move_freepages: start_pfn[0x81f600] end_pfn[0x81f7ff]
move_freepages: start_nid[1] end_nid[0]
My memory layout on this box is:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x0081ff5d
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] 1: 0x00800000 -> 0x0081f7ff
[ 0.000000] 1: 0x0081f800 -> 0x0081fe50
[ 0.000000] 1: 0x0081fed1 -> 0x0081fed8
[ 0.000000] 1: 0x0081feda -> 0x0081fedb
[ 0.000000] 1: 0x0081fedd -> 0x0081fee5
[ 0.000000] 1: 0x0081fee7 -> 0x0081ff51
[ 0.000000] 1: 0x0081ff59 -> 0x0081ff5d
So it's a block move in that 0x81f600-->0x81f7ff region which triggers
the problem.
This patch:
Declaration of early_pfn_to_nid() is scattered over per-arch include
files, and it seems it's complicated to know when the declaration is used.
I think it makes fix-for-memmap-init not easy.
This patch moves all declaration to include/linux/mm.h
After this,
if !CONFIG_NODES_POPULATES_NODE_MAP && !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use static definition in include/linux/mm.h
else if !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use generic definition in mm/page_alloc.c
else
-> per-arch back end function will be called.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: Bugfix
The ifdef for the apic clear on shutdown for the 64bit intel thermal
vector was incorrect and never triggered. Fix that.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: bug fix (with tolerant == 3)
do_exit cannot be called directly from the exception handler because
it can sleep and the exception handler runs on the exception stack.
Use force_sig() instead.
Based on a earlier patch by Ying Huang who debugged the problem.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Bug fix
This fixes a long standing bug in the machine check code. On resume the
boot CPU wouldn't get its vendor specific state like thermal handling
reinitialized. This means the boot cpu wouldn't ever get any thermal
events reported again.
Call the respective initialization functions on resume
v2: Remove ancient init because they don't have a resume device anyways.
Pointed out by Thomas Gleixner.
v3: Now fix the Subject too to reflect v2 change
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered. When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones. The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.
Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq(). But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.
A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts. It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
doc: mmiotrace.txt, buffer size control change
trace: mmiotrace to the tracer menu in Kconfig
mmiotrace: count events lost due to not recording
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: fix preemption bug
x86, olpc: fix model detection without OFW
x86, hpet: fix for LS21 + HPET = boot hang
x86: CPA avoid repeated lazy mmu flush
x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
x86/cpa: make sure cpa is safe to call in lazy mmu mode
x86, ptrace, mm: fix double-free on race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/vsx: Fix VSX alignment handler for regs 32-63
powerpc/ps3: Move ps3_mm_add_memory to device_initcall
powerpc/mm: Fix numa reserve bootmem page selection
powerpc/mm: Fix _PAGE_CHG_MASK to protect _PAGE_SPECIAL
|
|
* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Flush volatile msrs before emulating rdmsr
KVM: Fix assigned devices circular locking dependency
KVM: x86: fix LAPIC pending count calculation
KVM: Fix INTx for device assignment
KVM: MMU: Map device MMIO as UC in EPT
KVM: x86: disable kvmclock on non constant TSC hosts
KVM: PIT: fix i8254 pending count read
KVM: Fix racy in kvm_free_assigned_irq
KVM: Add kvm_arch_sync_events to sync with asynchronize events
KVM: mmu_notifiers release method
KVM: Avoid using CONFIG_ in userspace visible headers
KVM: ia64: fix fp fault/trap handler
|
|
Damien Wyart reported high ksoftirqd CPU usage (20%) on an
otherwise idle system.
The function-graph trace Damien provided:
> 799.521187 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521371 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521555 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521738 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521934 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522068 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.522208 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522392 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522575 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522759 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522956 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523074 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.523214 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523397 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523579 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523762 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523960 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524079 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.524220 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524403 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524587 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524770 | 1) <idle>-0 | | rcu_check_callbacks() {
> [ . . . ]
Shows rcu_check_callbacks() being invoked way too often. It should be called
once per jiffy, and here it is called no less than 22 times in about
3.5 milliseconds, meaning one call every 160 microseconds or so.
Why do we need to call rcu_pending() and rcu_check_callbacks() from the
idle loop of 32-bit x86, especially given that no other architecture does
this?
The following patch removes the call to rcu_pending() and
rcu_check_callbacks() from the x86 32-bit idle loop in order to
reduce the softirq load on idle systems.
Reported-by: Damien Wyart <damien.wyart@free.fr>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
controller
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Impact: use new API, fix SMP bug.
Use the new accessors rather than frobbing bits directly.
This also removes the bug introduced in ee0c468b (alpha: compile
fixes) which had Alpha setting bits on an on-stack cpumask, not the
cpu_online_map.
Cc: Richard Henderson <rth@twiddle.net>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
2fdf66b491ac706657946442789ec644cc317e1a
Impact: fix powernow-k8 when acpi=off (or other error).
There was a spurious change introduced into powernow-k8 in this patch:
so that we try to "restore" the cpus_allowed we never saved. We revert
that file.
See lkml "[PATCH] x86/powernow: fix cpus_allowed brokage when
acpi=off" from Yinghai for the bug report.
Cc: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cosmetic change in Kconfig menu layout
This patch was originally suggested by Peter Zijlstra, but seems it
was forgotten.
CONFIG_MMIOTRACE and CONFIG_MMIOTRACE_TEST were selectable
directly under the Kernel hacking / debugging menu in the kernel
configuration system. They were present only for x86 and x86_64.
Other tracers that use the ftrace tracing framework are in their own
sub-menu. This patch moves the mmiotrace configuration options there.
Since the Kconfig file, where the tracer menu is, is not architecture
specific, HAVE_MMIOTRACE_SUPPORT is introduced and provided only by
x86/x86_64. CONFIG_MMIOTRACE now depends on it.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Commit 3d2a71a596bd9c761c8487a2178e95f8a61da083 ("x86, traps: converge
do_debug handlers") changed the preemption disable logic of do_debug()
so vm86_handle_trap() is called with preemption disabled resulting in:
BUG: sleeping function called from invalid context at include/linux/kernel.h:155
in_atomic(): 1, irqs_disabled(): 0, pid: 3005, name: dosemu.bin
Pid: 3005, comm: dosemu.bin Tainted: G W 2.6.29-rc1 #51
Call Trace:
[<c050d669>] copy_to_user+0x33/0x108
[<c04181f4>] save_v86_state+0x65/0x149
[<c0418531>] handle_vm86_trap+0x20/0x8f
[<c064e345>] do_debug+0x15b/0x1a4
[<c064df1f>] debug_stack_correct+0x27/0x2c
[<c040365b>] sysenter_do_call+0x12/0x2f
BUG: scheduling while atomic: dosemu.bin/3005/0x10000001
Restore the original calling convention and reenable preemption before
calling handle_vm86_trap().
Reported-by: Michal Suchanek <hramrach@centrum.cz>
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Some msrs (notable MSR_KERNEL_GS_BASE) are held in the processor registers
and need to be flushed to the vcpu struture before they can be read.
This fixes cygwin longjmp() failure on Windows x64.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Simplify LAPIC TMCCT calculation by using hrtimer provided
function to query remaining time until expiration.
Fixes host hang with nested ESX.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Software are not allow to access device MMIO using cacheable memory type, the
patch limit MMIO region with UC and WC(guest can select WC using PAT and
PCD/PWT).
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This is better.
Currently, this code path is posing us big troubles,
and we won't have a decent patch in time. So, temporarily
disable it.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
count_load_time assignment is bogus: its supposed to contain what it
means, not the expiration time.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
In the past, kvm_get_kvm() and kvm_put_kvm() was called in assigned device irq
handler and interrupt_work, in order to prevent cancel_work_sync() in
kvm_free_assigned_irq got a illegal state when waiting for interrupt_work done.
But it's tricky and still got two problems:
1. A bug ignored two conditions that cancel_work_sync() would return true result
in a additional kvm_put_kvm().
2. If interrupt type is MSI, we would got a window between cancel_work_sync()
and free_irq(), which interrupt would be injected again...
This patch discard the reference count used for irq handler and interrupt_work,
and ensure the legal state by moving the free function at the very beginning of
kvm_destroy_vm(). And the patch fix the second bug by disable irq before
cancel_work_sync(), which may result in nested disable of irq but OK for we are
going to free it.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
kvm_arch_sync_events is introduced to quiet down all other events may happen
contemporary with VM destroy process, like IRQ handler and work struct for
assigned device.
For kvm_arch_sync_events is called at the very beginning of kvm_destroy_vm(), so
the state of KVM here is legal and can provide a environment to quiet down other
events.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Kconfig symbols are not available in userspace, and are not stripped by
headers-install. Avoid their use by adding #defines in <asm/kvm.h> to
suit each architecture.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The floating-point registers f6-f11 is used by vmm and
saved in kvm-pt-regs, so should set the correct bit mask
and the pointer in fp_state, otherwise, fpswa may touch
vmm's fp registers instead of guests'.
In addition, for fp trap handling, since the instruction
which leads to fp trap is completely executed, so can't
use retry machanism to re-execute it, because it may
pollute some registers.
Signed-off-by: Yang Zhang <yang.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
