| Age | Commit message (Collapse) | Author |
|---|
|
The ldp board file currently requests gpios required to configure the NEC DPI
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Configure the gpio information in generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
The am3517 board file currently requests gpios required to configure the sharp
lq DPI panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to generic dpi panel's platform data so that it's
passed to the panel driver.
Note: It's not clear why the GPIOs were muxed as input signals in PULL down mode
in am3517_evm_display_init(). Also, only the LCD_PANEL_PWR was toggled in the
platform_enable/disable calls, the generic DPI panel driver will now toggle all
the three gpios on panel's disable/enable. We need to test if these changes to
see if they have any impact or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
The cm-t35 board file currently requests gpios required to configure the tdo35s
panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to generic dpi panel's platform data so that it's
passed to the panel driver.
Note: Only BL enable gpio is handled in the panel driver. The LCD enable
GPIO is handled in the board file at init time, as there's a 50 ms delay
required when using the GPIO, and the panel driver doesn't know about
that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The devkit8000 board file currently requests gpios required to configure the
innolux DPI panel, and provides platform_enable/disable callbacks to configure
them.
These tasks have been moved to the generic dpi panel driver itself and should
be removed from the board files.
Remove the gpio request and the platform callbacks from the board file.
Configure the gpio information in generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
The 2430sdp board file currently requests gpios required to configure the NEC
DPI panel, and provides platform_enable/disable callbacks to configure them.
These tasks have been moved to the generic dpi panel driver itself and shouldn't
be done in the board files.
Remove the gpio requests and the platform callbacks from the board file.
Add the gpio information to generic dpi panel's platform data so that it's
passed to the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
Use pwm_leds driver for the keyboard light and pwm-backlight for the lcd
backlight control (instead of implementing the PWM driver part in the board
file).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Structs for platform data of omapdss panels are found in headers in the
'include/video/' path. Board files populate these structs with platform
specific values, and the panel driver uses these to configure the panel.
Currently, each panel has it's own header in the above path. Move all the
omapdss panel platform data structs to a single header omap-panel-data.h.
This is useful because:
- All other omapdss panel drivers will be modified to use platform data. This
would lead to a lot of panel headers usable only by omapdss. A lot of these
platform data structs are trivial, and don't really need a separate header.
- Platform data would be eventually removed, and platform information would be
passed via device tree. Therefore, omapdss panel platform data structs are
temporary, and will be easier to remove if they are all in the same header.
- All board files will have to include the same header to configure a panel's
platform data, that makes the board files more consistent.
Signed-off-by: Archit Taneja <archit@ti.com>
|
|
Commit 3e7fc708eb41 ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't
finish the job, leaving an un-initialized reference to (*idle)().
[ Haven't seen a crash from this - but seems like we are just being
lucky that "idle" is zero so it does get initialized before we jump to
randomland - Len ]
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull arc architecture fixes from Vineet Gupta:
"This includes fix for a serious bug in DMA mapping API, make
allyesconfig wreckage, removal of bogus email-list placeholder in
MAINTAINERS, a typo in ptrace helper code and last remaining changes
for syscall ABI v3 which we are finally starting to transition-to
internally.
The request is late than I intended to - but I was held up with
debugging a timer link list corruption, for which a proposed fix to
generic timer code was sent out to lkml/tglx earlier today."
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix the typo in event identifier flags used by ptrace
arc: fix dma_address assignment during dma_map_sg()
ARC: Remove SET_PERSONALITY (tracks cross-arch change)
ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI
ARC: ABIv3: Print the correct ABI ver
ARC: make allyesconfig build breakages
ARC: MAINTAINERS update for ARC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Fix for a recent cpufreq regression related to acpi-cpufreq and
suspend/resume from Viresh Kumar.
- cpufreq stats reference counting fix from Viresh Kumar.
- intel_pstate driver fixes from Dirk Brandewie and Konrad Rzeszutek
Wilk.
- New ACPI suspend blacklist entry for Sony Vaio VGN-FW21M from Fabio
Valentini.
- ACPI Platform Error Interface (APEI) fix from Chen Gong.
- PCI root bridge hotplug locking fix from Yinghai Lu.
* tag 'pm+acpi-3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / ACPI: hold acpi_scan_lock during root bus hotplug
ACPI / APEI: fix error status check condition for CPER
ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init()
cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get()
intel-pstate: Use #defines instead of hard-coded values.
cpufreq / intel_pstate: Fix calculation of current frequency
cpufreq / intel_pstate: Add function to check that all MSRs are valid
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fix from Catalin Marinas:
"Fix IS_ENABLED() usage typo (missing CONFIG_ prefix)."
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
ARM64: early_printk: Fix check for CONFIG_ARM64_64K_PAGES
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes
Pull powerpc build fixes from Stephen Rothwell:
"Just a couple of build fixes for powerpc all{mod,yes}config.
Submitted by me since BenH is on vacation."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
powerpc: define the conditions where the ePAPR idle hcall can be supported
powerpc: make additional room in exception vector area
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"This is mostly just the last stragglers of the regression bugs that
this merge window had. There are also two bug-fixes: one that adds an
extra layer of security, and a regression fix for a change that was
added in v3.7 (the v1 was faulty, the v2 works).
- Regression fixes for C-and-P states not being parsed properly.
- Fix possible security issue with guests triggering DoS via
non-assigned MSI-Xs.
- Fix regression (introduced in v3.7) with raising an event (v2).
- Fix hastily introduced band-aid during c0 for the CR3 blowup."
* tag 'stable/for-linus-3.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/events: avoid race with raising an event in unmask_evtchn()
xen/mmu: Move the setting of pvops.write_cr3 to later phase in bootup.
xen/acpi-stub: Disable it b/c the acpi_processor_add is no longer called.
xen-pciback: notify hypervisor about devices intended to be assigned to guests
xen/acpi-processor: Don't dereference struct acpi_processor on all CPUs.
|
|
We move the setting of write_cr3 from the early bootup variant
(see git commit 0cc9129d75ef8993702d97ab0e49542c15ac6ab9
"x86-64, xen, mmu: Provide an early version of write_cr3.")
to a more appropiate location.
This new location sets all of the other non-early variants
of pvops calls - and most importantly is before the
alternative_asm mechanism kicks in.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
For 32-bit, CONFIG_EPAPR_PARAVIRT pulls in both epapr_paravirt.c
and epapr_hcalls.c which contains the 32-bit paravirt idle loop.
For 64-bit, the paravirt idle loop is in idle_book3e.S and that
source file is included only if CONFIG_PPC_BOOK3E_64 defined.
This patch makes that dependency for 64-bit explicit.
Fixes these build errors:
arch/powerpc/kernel/built-in.o: In function `restore_pblist_ptr':
ftrace.c:(.toc+0xdc0): undefined reference to `epapr_ev_idle_start'
ftrace.c:(.toc+0xdd0): undefined reference to `epapr_ev_idle'
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
The 'CONFIG_' prefix is not implicit in IS_ENABLED().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
|
|
They are defined in coreboot (MSR_PLATFORM) and the other
one is already defined in msr-index.h.
Let's use those.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The FWNMI region is fixed at 0x7000 and the vector are now overflowing
that with allmodconfig. Fix that by moving slb_miss_realmode code out
of that region as it doesn't need to be that close to the call sites
(it is a _GLOBAL function)
Fixes this build error:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1304: Error: attempt to move .org backwards
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A collection of minor fixes, more EFI variables paranoia
(anti-bricking) plus the ability to disable the pstore either as a
runtime default or completely, due to bricking concerns."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efivars: Fix check for CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE
x86, microcode_intel_early: Mark apply_microcode_early() as cpuinit
efivars: Handle duplicate names from get_next_variable()
efivars: explicitly calculate length of VariableName
efivars: Add module parameter to disable use as a pstore backend
efivars: Allow disabling use as a pstore backend
x86-32, microcode_intel_early: Fix crash with CONFIG_DEBUG_VIRTUAL
x86-64: Fix the failure case in copy_user_handle_tail()
|
|
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
|
|
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For MSI-X capable devices the hypervisor wants to write protect the
MSI-X table and PBA, yet it can't assume that resources have been
assigned to their final values at device enumeration time. Thus have
pciback do that notification, as having the device controlled by it is
a prerequisite to assigning the device to guests anyway.
This is the kernel part of hypervisor side commit 4245d33 ("x86/MSI:
add mechanism to fully protect MSI-X table from PV guest accesses") on
the master branch of git://xenbits.xen.org/xen.git.
CC: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Add missing __cpuinit annotation to apply_microcode_early().
Reported-by: Shaun Ruffell <sruffell@digium.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/20130320170310.GA23362@digium.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 3:
- Add the lost dependency check for DEBUG_IMX_UART_PORT back
* tag 'imx-fixes-3.9-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A fair chunk of the linecount comes from a fix for a tracing bug that
corrupts latency tracing buffers when the overwrite mode is changed on
the fly - the rest is mostly assorted fewliner fixlets."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Add SNB/SNB-EP scheduling constraints for cycle_activity event
kprobes/x86: Check Interrupt Flag modifier when registering probe
kprobes: Make hash_64() as always inlined
perf: Generate EXIT event only once per task context
perf: Reset hwc->last_period on sw clock events
tracing: Prevent buffer overwrite disabled for latency tracers
tracing: Keep overwrite in sync between regular and snapshot buffers
tracing: Protect tracer flags with trace_types_lock
perf tools: Fix LIBNUMA build with glibc 2.12 and older.
tracing: Fix free of probe entry by calling call_rcu_sched()
perf/POWER7: Create a sysfs format entry for Power7 events
perf probe: Fix segfault
libtraceevent: Remove hard coded include to /usr/local/include in Makefile
perf record: Fix -C option
perf tools: check if -DFORTIFY_SOURCE=2 is allowed
perf report: Fix build with NO_NEWT=1
perf annotate: Fix build with NO_NEWT=1
tracing: Fix race in snapshot swapping
|
|
orig_r8_IS_EXCPN and orig_r8_IS_BRKPT were same values due to a
copy/paste error. Although it looks bad and is wrong, it really doesn't
affect gdb working.
orig_r8_IS_BRKPT is the one relevant to debugging (breakpoints), since
it is used to provide EFA vs. ERET to a ptrace "stop_pc" request.
So when gdb has inserted a breakpoint, orig_r8_IS_BRKPT is already set,
and anything else (i.e. orig_r8_IS_EXCPN) becoming same as it, really
doesn't hurt gdb. The corollary case, could be nasty but nobody uses the
ptrace "stop_pc" request in that case
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
In 32-bit, __pa_symbol() in CONFIG_DEBUG_VIRTUAL accesses kernel data
(e.g. max_low_pfn) that not only hasn't been setup yet in such early
boot phase, but since we are in linear mode, cannot even be detected
as uninitialized.
Thus, use __pa_nodebug() rather than __pa_symbol() to get a global
symbol's physical address.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1363705484-27645-1-git-send-email-fenghua.yu@intel.com
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Once instance of this Kconfig macro remained after commit
51acbcec6c42b24482bac18e42befc822524535d ("md: remove
CONFIG_MULTICORE_RAID456"). Remove that one too. And, while we're at it,
also remove it from the defconfig files that carry it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull kvm fixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix bounds checking in ioapic indirect register reads (CVE-2013-1798)
KVM: x86: Convert MSR_KVM_SYSTEM_TIME to use gfn_to_hva_cache functions (CVE-2013-1797)
KVM: x86: fix for buffer overflow in handling of MSR_KVM_SYSTEM_TIME (CVE-2013-1796)
KVM: x86: fix deadlock in clock-in-progress request handling
KVM: allow host header to be included even for !CONFIG_KVM
|
|
Pull sparc fixes from David Miller:
"Just some minor fixups, a sunsu console setup panic cure, and
recognition of a Fujitsu sun4v cpu."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove unused "config BITS"
sparc: delete "if !ULTRA_HAS_POPULATION_COUNT"
sparc64: correctly recognize SPARC64-X chips
sparc,leon: fix GRPCI2 device0 PCI config space access
sunsu: Fix panic in case of nonexistent port at "console=ttySY" cmdline option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Fix !SMP build error.
- Fix padding computation in struct ucontext (no ABI change).
- Minor clean-up after the signal patches (unused var).
- Two old Kconfig options clean-up.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
arm64: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
arm64: fix padding computation in struct ucontext
arm64: Fix build error with !SMP
arm64: Removed unused variable in compat_setup_rt_frame()
|
|
sparc's asm/module.h got removed in commit
786d35d45cc40b2a51a18f73e14e135d47fdced7 ("Make most arch asm/module.h
files use asm-generic/module.h"). That removed the only two uses of this
Kconfig symbol. So we can remove its entry too.
> >From arch/sparc/Makefile:
> ifeq ($(CONFIG_SPARC32),y)
> [...]
>
> [...]
> export BITS := 32
> [...]
>
> else
> [...]
>
> [...]
> export BITS := 64
> [...]
>
> So $(BITS) is set depending on whether CONFIG_SPARC32 is set or not.
> Using $(BITS) in sparc's Makefiles is not using CONFIG_BITS. That
> doesn't count as usage of "config BITS".
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
|
|
Commit 2d78d4beb64eb07d50665432867971c481192ebf ("[PATCH] bitops:
sparc64: use generic bitops") made the default of GENERIC_HWEIGHT depend
on !ULTRA_HAS_POPULATION_COUNT. But since there's no Kconfig symbol with
that name, this always evaluates to true. Delete this dependency.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(CVE-2013-1797)
There is a potential use after free issue with the handling of
MSR_KVM_SYSTEM_TIME. If the guest specifies a GPA in a movable or removable
memory such as frame buffers then KVM might continue to write to that
address even after it's removed via KVM_SET_USER_MEMORY_REGION. KVM pins
the page in memory so it's unlikely to cause an issue, but if the user
space component re-purposes the memory previously used for the guest, then
the guest will be able to corrupt that memory.
Tested: Tested against kvmclock unit test
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
(CVE-2013-1796)
If the guest sets the GPA of the time_page so that the request to update the
time straddles a page then KVM will write onto an incorrect page. The
write is done byusing kmap atomic to get a pointer to the page for the time
structure and then performing a memcpy to that page starting at an offset
that the guest controls. Well behaved guests always provide a 32-byte aligned
address, however a malicious guest could use this to corrupt host kernel
memory.
Tested: Tested against kvmclock unit test.
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
The Kconfig entry for DEBUG_ERRORS is a verbatim copy of the former arm
entry for that symbol. It got removed in v2.6.39 because it wasn't
actually used anywhere. There are still no users of DEBUG_ERRORS so
remove this entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[catalin.marinas@arm.com: removed option from defconfig]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Config option GENERIC_HARDIRQS_NO_DEPRECATED was removed in commit
78c89825649a9a5ed526c507603196f467d781a5 ("genirq: Remove the now obsolete
config options and select statements"), but the select was accidentally
reintroduced in commit 8c2c3df31e3b87cb5348e48776c366ebd1dc5a7a ("arm64:
Build infrastructure").
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
While adding i.MX DEBUG_LL selection, commit f8c95fe (ARM: imx: support
DEBUG_LL uart port selection for all i.MX SoCs) leaves Kconfig symbol
DEBUG_IMX_UART_PORT there without any dependency check. This results in
that everyone gets the symbol in their config, which is someting
undesirable. Add "depends on ARCH_MXC" for the symbol to prevent that.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The issue fixed by this patch manifests only then using X11
with mxsfb driver. The X11 will display either shifted image
or otherwise distorted image on the LCD.
The problem is that the X11 tries to reconfigure the framebuffer
and along the way calls fb_ops.fb_set_par() with X11's desired
configuration values. The field of particular interest is
fb_info->var.sync which contains non-standard values if
configured by kernel. These are either FB_SYNC_DATA_ENABLE_HIGH_ACT,
FB_SYNC_DOTCLK_FAILING_ACT or both, depending on the platform
configuration. Both of these values are defined in the
include/linux/mxsfb.h file.
The driver interprets these values and configures the LCD controller
accordingly. Yet X11 only has access to the standard values for this
field defined in include/uapi/linux/fb.h and thus, unlike kernel,
omits these special values. This results in distorted image on the
LCD.
This patch moves these non-standard values into new field of the
mxsfb_platform_data structure so the driver can in turn check this
field instead of the video mode field for these specific portions.
Moreover, this patch prefixes these values with MXSFB_SYNC_ prefix
instead of FB_SYNC_ prefix to prevent confusion of subsequent users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM <linux-arm-kernel@lists.infradead.org>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Lothar Waßmann <LW@karo-electronics.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Somehow the driver snuck in with these still in it.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a deadlock in pvclock handling:
cpu0: cpu1:
kvm_gen_update_masterclock()
kvm_guest_time_update()
spin_lock(pvclock_gtod_sync_lock)
local_irq_save(flags)
spin_lock(pvclock_gtod_sync_lock)
kvm_make_mclock_inprogress_request(kvm)
make_all_cpus_request()
smp_call_function_many()
Now if smp_call_function_many() called by cpu0 tries to call function on
cpu1 there will be a deadlock.
Fix by moving pvclock_gtod_sync_lock protected section outside irq
disabled section.
Analyzed by Gleb Natapov <gleb@redhat.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Reported-and-Tested-by: Yongjie Ren <yongjie.ren@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
The increment of "to" in copy_user_handle_tail() will have incremented
before a failure has been noted. This causes us to skip a byte in the
failure case.
Only do the increment when assured there is no failure.
Signed-off-by: CQ Tang <cq.tang@intel.com>
Link: http://lkml.kernel.org/r/20130318150221.8439.993.stgit@phlsvslse11.ph.intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes, the most hairy on is the flush_tlb_kernel_range
fix. Another case of "how could this ever have worked?"."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kdump: Do not add standby memory for kdump
drivers/i2c: remove !S390 dependency, add missing GENERIC_HARDIRQS dependencies
s390/scm: process availability
s390/scm_blk: suspend writes
s390/scm_drv: extend notify callback
s390/scm_blk: fix request number accounting
s390/mm: fix flush_tlb_kernel_range()
s390/mm: fix vmemmap size calculation
s390: critical section cleanup vs. machine checks
|
|
Pull ARM SoC bug fixes from Arnd Bergmann:
"Things are calming down for arm-soc as well. This set of bug fixes is
dominated in size by the at91 platform bug fixes. Some of them were
meant to go through the framebuffer tree during the merge window, but
since the framebuffer maintainer could not be reached, I offered to
take them here. The other notable at91 change is the addition of
pinctrl definitions to fix the NAND controller.
The rest are mostly simple regression fixes:
- Our removal of VIRT_TO_BUS conflicted with Stephen Rothwell's
renaming of the Kconfig symbol. You will get a trivial merge
conflict here, we still want to remove it.
- missing bits for clocks on imx and s5pv210
- missing header inclusions in mmp and shmobile
- typos in s5pv210 camera and vt8500 clock support code
and three trivial fixes for pre-3.8 bugs:
- an old bogus build warning in the joystick driver
- a misleading Kconfig description
- a NULL pointer check on davinci"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: fix CONFIG_VIRT_TO_BUS handling
ARM: i.MX35: enable MAX clock
ARM: Scorpion is a v7 architecture, not v6
ARM: mmp: add platform_device head file in gplugd
input/joystick: use get_cycles on ARM
[media] s5p-fimc: fix s5pv210 build
clk: vt8500: Fix "fix device clock divisor calculations"
ARM: i.MX25: Fix DT compilation
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830
ARM: shmobile: marzen: Include mmc/host.h
ARM: EXYNOS: Add #dma-cells for generic dma binding support for PL330
ARM: S5PV210: Fix PL330 DMA controller clkdev entries
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here's a few powerpc fixes for 3.9, mostly regressions (though not all
from 3.9 merge window) that we've been hammering into shape over the
last couple of weeks. They fix booting on Cell and G5 among other
things (yes, we've been a bit sloppy with older machines this time
around)."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Rename USER_ESID_BITS* to ESID_BITS*
powerpc: Update kernel VSID range
powerpc: Make VSID_BITS* dependency explicit
powerpc: Make sure that we alays include CONFIG_BINFMT_ELF
powerpc/ptrace: Fix brk.len used uninitialised
powerpc: Fix -mcmodel=medium breakage in prom_init.c
powerpc: Remove last traces of POWER4_ONLY
powerpc: Fix cputable entry for 970MP rev 1.0
powerpc: Fix STAB initialization
|
|
Pull ARM fixes from Russell King:
"Just three fixes this time - a fix for a fix for our memset function,
fixing the dummy clockevent so that it doesn't interfere with real
hardware clockevents, and fixing a build error for Tegra."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7675/1: amba: tegra-ahb: Fix build error w/ PM_SLEEP w/o PM_RUNTIME
ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
ARM: 7670/1: fix the memset fix
|
|
887cbce0 "arch Kconfig: centralise CONFIG_ARCH_NO_VIRT_TO_BUS"
and 4febd95a8 "Select VIRT_TO_BUS directly where needed" from
Stephen Rothwell changed globally how CONFIG_VIRT_TO_BUS is
selected, while my own a5d533ee0 "ARM: disable virt_to_bus/
virt_to_bus almost everywhere" was merged at the same time and
changed which platforms select it on ARM.
The result of this conflict was that we again see CONFIG_VIRT_TO_BUS
on all ARM systems. This patch fixes up the problem and removes
CONFIG_ARCH_NO_VIRT_TO_BUS again on ARM.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
|
