| Age | Commit message (Collapse) | Author |
|---|
|
|
|
processor.bm_check_disable=1" prevents Linux from checking BM_STS
before entering C3-type cpu power states.
This may be useful for a system running acpi_idle
where the BIOS exports FADT C-states, _CST IO C-states,
or _CST FFH C-states with the BM_STS bit set;
while configuring the chipset to set BM_STS
more frequently than perhaps is optimal.
Note that such systems may have been developed
using a tickful OS that would quickly clear BM_STS,
rather than a tickless OS that may go for some time
between checking and clearing BM_STS.
Note also that an alternative for newer systems
is to use the intel_idle driver, which always
ignores BM_STS, relying Linux device drivers
to register constraints explicitly via PM_QOS.
https://bugzilla.kernel.org/show_bug.cgi?id=15886
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It turns out that there is a bit in the _CST for Intel FFH C3
that tells the OS if we should be checking BM_STS or not.
Linux has been unconditionally checking BM_STS.
If the chip-set is configured to enable BM_STS,
it can retard or completely prevent entry into
deep C-states -- as illustrated by turbostat:
http://userweb.kernel.org/~lenb/acpi/utils/pmtools/turbostat/
ref: Intel Processor Vendor-Specific ACPI Interface Specification
table 4 "_CST FFH GAS Field Encoding"
Bit 1: Set to 1 if OSPM should use Bus Master avoidance for this C-state
https://bugzilla.kernel.org/show_bug.cgi?id=15886
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
CONFIG_ACPI_PROCFS=n:
drivers/acpi/processor_idle.c:83: warning: 'us_to_pm_timer_ticks' defined but not used.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_enter_[simple|bm] routines does us to pm tick conversion on every
idle wakeup and the value is only used in /proc/acpi display. We can
store the time in us and convert it into pm ticks before printing instead and
avoid the conversion in the common path.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The C-state idle time is not calculated correctly, which will return the wrong
residency time in C-state. It will have the following effects:
1. The system can't choose the deeper C-state when it is idle next time.
Of course the system power is increased. E.g. On one server machine about 40W
idle power is increased.
2. The powertop shows that it will stay in C0 running state about 95% time
although the system is idle at most time.
2.6.35-rc1 regression caused-by: 2da513f582a96c053aacc2c92873978d2ea7abff
(ACPI: Minor cleanup eliminating redundant PMTIMER_TICKS to NS conversion)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Yu Zhidong <zhidong.yu@intel.com>
Tested-by: Yu Zhidong <zhidong.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: native hardware cpuidle driver for latest Intel processors
ACPI: acpi_idle: touch TS_POLLING only in the non-MWAIT case
acpi_pad: uses MONITOR/MWAIT, so it doesn't need to clear TS_POLLING
sched: clarify commment for TS_POLLING
ACPI: allow a native cpuidle driver to displace ACPI
cpuidle: make cpuidle_curr_driver static
cpuidle: add cpuidle_unregister_driver() error check
cpuidle: fail to register if !CONFIG_CPU_IDLE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
ACPI: Don't let acpi_pad needlessly mark TSC unstable
drivers/acpi/sleep.h: Checkpatch cleanup
ACPI: Minor cleanup eliminating redundant PMTIMER_TICKS to NS conversion
ACPI: delete unused c-state promotion/demotion data strucutures
ACPI: video: fix acpi_backlight=video
ACPI: EC: Use kmemdup
drivers/acpi: use kasprintf
ACPI, APEI, EINJ injection parameters support
Add x64 support to debugfs
ACPI, APEI, Use ERST for persistent storage of MCE
ACPI, APEI, Error Record Serialization Table (ERST) support
ACPI, APEI, Generic Hardware Error Source memory error support
ACPI, APEI, UEFI Common Platform Error Record (CPER) header
Unified UUID/GUID definition
ACPI Hardware Error Device (PNP0C33) support
ACPI, APEI, PCIE AER, use general HEST table parsing in AER firmware_first setup
ACPI, APEI, Document for APEI
ACPI, APEI, EINJ support
ACPI, APEI, HEST table parsing
ACPI, APEI, APEI supporting infrastructure
...
|
|
acpi_enter_[simple,bm] does
idle timing in ns, convert it to timeval, then to us, then to
pmtimer_ticks and then back to ns.
This patch changes things to
idle timing in ns, convert it to us, and then to pmtimer_ticks.
Just saves an imul along this path, but makes the code cleaner.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
commit d306ebc28649b89877a22158fe0076f06cc46f60
(ACPI: Be in TS_POLLING state during mwait based C-state entry)
fixed an important power & performance issue where ACPI c2 and c3 C-states
were clearing TS_POLLING even when using MWAIT (ACPI_STATE_FFH).
That bug had been causing us to receive redundant scheduling interrups
when we had already been woken up by MONITOR/MWAIT.
Following up on that...
In the MWAIT case, we don't have to subsequently
check need_resched(), as that c heck was there
for the TS_POLLING-clearing case.
Note that not only does the cpuidle calling function
already check need_resched() before calling us, the
low-level entry into monitor/mwait calls it twice --
guaranteeing that a write to the trigger address
can not go un-noticed.
Also, in this case, we don't have to set TS_POLLING
when we wake, because we never cleared it.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
|
|
These were used before cpuidle by the native ACPI idle driver,
which tracked promotion and demotion between states.
The code was referenced by CONFIG_ACPI_PROCFS
for /proc/acpi/processor/*/power,
but as we no longer do promotion/demotion, that
reference has been a NOP since the transition.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
|
|
ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.
This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.
The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).
Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4
Reported-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Since the rewrite of the CPU idle governor in 2.6.32, two laptops have
surfaced where the BIOS advertises a C2 power state, but for some reason
this state is not functioning (as verified in both cases by powertop
before the patch in .32).
The old governor had the accidental behavior that if a non-working state
was chosen too many times, it would end up falling back to C1. The new
governor works differently and this accidental behavior is no longer
there; the result is a high temperature on these two machines.
This patch adds these 2 machines to the DMI table for C state anomalies;
by just not using C2 both these machines are better off (the TSC can be
used instead of the pm timer, giving a performance boost for example).
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14742
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-by: <akwatts@ymail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
no functional change -- cleanup only.
acpi_processor_power_verify_c2() was nearly empty due to a previous patch,
so expand its remains into its one caller and delete it.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Do for C3 what the previous patch did for C2.
The C2 patch was in response to a highly visible
and multiply reported C-state/turbo failure,
while this change has no bug report in-hand.
This will enable C3 in Linux on systems where BIOS
overstates C3 latency in _CST. It will also enable
future systems which may actually have C3 > 1000usec.
Linux has always ignored ACPI BIOS C3 with exit latency > 1000 usec,
and the ACPI spec is clear that is correct FADT-supplied C3.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 1000usec C3 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Linux has always ignored ACPI BIOS C2 with exit latency > 100 usec,
and the ACPI spec is clear that is correct FADT-supplied C2.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 100usec C2 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
This bug has not been visible until Nehalem, which advertises
a CPU-C2 worst case exit latency on servers of 205usec.
That (incorrect) figure is being used by BIOS writers
on mobile Nehalem systems for the AC configuration.
Thus, Linux ignores C2 leaving just C1, which is
saves less power, and also impacts performance
by preventing the use of turbo mode.
http://bugzilla.kernel.org/show_bug.cgi?id=15064
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
I got following warning on ia64 box:
In function 'acpi_processor_power_verify':
642: warning: passing argument 2 of 'smp_call_function_single' from
incompatible pointer type
This smp_call_function_single() was introduced by a commit
f833bab87fca5c3ce13778421b1365845843b976:
> @@ -162,8 +162,9 @@
> pr->power.timer_broadcast_on_state = state;
> }
>
> -static void lapic_timer_propagate_broadcast(struct acpi_processor *pr)
> +static void lapic_timer_propagate_broadcast(void *arg)
> {
> + struct acpi_processor *pr = (struct acpi_processor *) arg;
> unsigned long reason;
>
> reason = pr->power.timer_broadcast_on_state < INT_MAX ?
> @@ -635,7 +636,8 @@
> working++;
> }
>
> - lapic_timer_propagate_broadcast(pr);
> + smp_call_function_single(pr->id, lapic_timer_propagate_broadcast,
> + pr, 1);
>
> return (working);
> }
The problem is that the lapic_timer_propagate_broadcast() has 2 versions:
One is real code that modified in the above commit, and the other is NOP
code that used when !ARCH_APICTIMER_STOPS_ON_C3:
static void lapic_timer_propagate_broadcast(struct acpi_processor *pr) { }
So I got warning because of !ARCH_APICTIMER_STOPS_ON_C3.
We really want to do nothing here on !ARCH_APICTIMER_STOPS_ON_C3, so
modify lapic_timer_propagate_broadcast() of real version to use
smp_call_function_single() in it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Commit 3d5b6fb47a8e68fa311ca2c3447e7f8a7c3a9cf3 ("ACPI: Kill overly
verbose "power state" log messages") removed the actual use of this
variable, but didn't remove the variable itself, resulting in build
warnings like
drivers/acpi/processor_idle.c: In function ‘acpi_processor_power_init’:
drivers/acpi/processor_idle.c:1169: warning: unused variable ‘i’
Just get rid of the now unused variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I was recently lucky enough to get a 64-CPU system, so my kernel log
ends up with 64 lines like:
ACPI: CPU0 (power states: C1[C1] C2[C3])
This is pretty useless clutter because this info is already available
after boot from both /sys/devices/system/cpu/cpu*/cpuidle/state?/ as
well as /proc/acpi/processor/CPU*/power.
So just delete the code that prints the C-states in processor_idle.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
drivers/acpi/processor_idle.c:1162: warning: unused variable ‘entry’
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
'bugzilla-12904', 'bugzilla-13121', 'bugzilla-13396', 'bugzilla-13533', 'bugzilla-13612', 'c3_lock', 'hid-cleanups', 'misc-2.6.31', 'pdc-leak-fix', 'pnpacpi', 'power_nocheck', 'thinkpad_acpi', 'video' and 'wmi' into release
|
|
Now whether the ACPI processor proc I/F is registered depends on the
CONFIG_PROC. It had better depend on the CONFIG_ACPI_PROCFS.
When the CONFIG_ACPI_PROCFS is unset in kernel configuration, the
ACPI processor proc I/F won't be registered.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
cosmetic only. The lapic_timer workaround routines
are specific to the lapic_timer, and are not acpi-generic.
old:
acpi_timer_check_state()
acpi_propagate_timer_broadcast()
acpi_state_timer_broadcast()
new:
lapic_timer_check_state()
lapic_timer_propagate_broadcast()
lapic_timer_state_broadcast()
also, simplify the code in acpi_processor_power_verify()
so that lapic_timer_check_state() is simply called
from one place for all valid C-states, including C1.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock
by skipping the fake ARB_DISABLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When AMD C1E is enabled, local APIC timer will stop even in C1. To avoid
suspend/resume hang, this patch removes C1 and replace it with a cpu_relax() in
suspend/resume path. This hasn't any impact in runtime path.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid suspend/resume hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When AMD C1E is enabled, local APIC timer will stop even in C1.
This patch uses broadcast IPI to replace local APIC timer in C1.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid boot hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
'bugzilla-13121', 'bugzilla-13165', 'bugzilla-13243', 'bugzilla-13259', 'resume-sci-en-regression', 'thermal-regression', 'tsc-regression' and 'asus-2.6.30' into release
|
|
Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:
Marking TSC unstable due to TSC halts in idle
But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A previous 2.6.30 patch, a71e4917dc0ebbcb5a0ecb7ca3486643c1c9a6e2,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.
Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Frans Pop <elendil@planet.nl>
|
|
In 2.6.29,
31878dd86b7df9a147f5e6cc6e07092b4308782b
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.
But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume. So now the kernel restores BM_RLD.
http://bugzilla.kernel.org/show_bug.cgi?id=13032
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
|
|
As processor.max_cstate is an init-time-only modparam,
sanity checking it at init-time is sufficient.
http://bugzilla.kernel.org/show_bug.cgi?id=13142
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Linux tells ICH4 users that they can (manually) invoke
"hpet=force" to enable the undocumented ICH-4M HPET.
The HPET becomes available for both clocksource and clockevents.
But as of ff69f2bba67bd45514923aaedbf40fe351787c59
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
the HPET may be used via clocksource for idle accounting, and
hpet=force on an ICH4 box hangs boot.
It turns out that touching the MMIO HPET withing
the ARB_DIS part of C3 will hang the hardware.
The fix is to simply move the timer access outside
the ARB_DIS region. This is a no-op on modern hardware
because ARB_DIS is no longer used.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Linux-2.6.29 deleted the legacy ACPI idle handler, leaving
the CPU_IDLE handler, which does not track bus master activity.
So delete the unused bm_activity field -- it is confusing to
print an always zero value.
This patch could break programs that parse
/proc/acpi/processor/*/power, since it deletes this
line from that file:
bus master activity: 00000000
http://bugzilla.kernel.org/show_bug.cgi?id=13145
is not fixed by this patch, but provoked this patch.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The c2 and c3 idle handlers check tsc_halts_in_c()
after every time they return from idle. Um, when?:-)
Move this check to init-time to remove the unnecessary
run-time overhead, and also to have the check complete before
the first entry into the idle handler.
ff69f2bba67bd45514923aaedbf40fe351787c59
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
replaced the hard-coded use of the PM-timer inside idle,
with ktime_get_readl(), which possibly uses the TSC --
so it is now especially prudent to detect a broken TSC
before entering idle.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
The recent ACPICA patch
(ACPICA: FADT: Favor 32-bit register addresses for compatibility)
makes machine to use the right FADT HW addresses
and C-states now work fine.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Mark Doughty <me@markdoughty.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Removed locking for reads from the ACPI bit registers in PM1
Status, Enable, Control, and PM2 Control. The lock is not required
when reading the single-bit registers. The acpi_get_register_unlocked
function is no longer needed and has been removed. This will
improve performance for reads on these registers. ACPICA BZ 760.
http://www.acpica.org/bugzilla/show_bug.cgi?id=760
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
We found Cx states time abnormal in our some of machines which have 16
LCPUs, the C0 take too many time while system is really idle when kernel
enabled tickless and highres. powertop output is below:
PowerTOP version 1.9 (C) 2007 Intel Corporation
Cn Avg residency P-states (frequencies)
C0 (cpu running) (40.5%) 2.53 Ghz 0.0%
C1 0.0ms ( 0.0%) 2.53 Ghz 0.0%
C2 128.8ms (59.5%) 2.40 Ghz 0.0%
1.60 Ghz 100.0%
Wakeups-from-idle per second : 4.7 interval: 20.0s
no ACPI power usage estimate available
Top causes for wakeups:
41.4% ( 24.9) <interrupt> : extra timer interrupt
20.2% ( 12.2) <kernel core> : usb_hcd_poll_rh_status
(rh_timer_func)
After tacking detailed for this issue, Yakui and I find it is due to 24
bit PM timer overflows when some of cpu sleep more than 4 seconds. With
tickless kernel, the CPU want to sleep as much as possible when system
idle. But the Cx sleep time are recorded by pmtimer which length is
determined by BIOS. The current Cx time was gotten in the following
function from driver/acpi/processor_idle.c:
static inline u32 ticks_elapsed(u32 t1, u32 t2)
{
if (t2 >= t1)
return (t2 - t1);
else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER))
return (((0x00FFFFFF - t1) + t2) & 0x00FFFFFF);
else
return ((0xFFFFFFFF - t1) + t2);
}
If pmtimer is 24 bits and it take 5 seconds from t1 to t2, in above
function, just about 1 seconds ticks was recorded. So the Cx time will be
reduced about 4 seconds. and this is why we see above powertop output.
To resolve this problem, Yakui and I use ktime_get() to record the Cx
states time instead of PM timer as the following patch. the patch was
tested with i386/x86_64 modes on several platforms.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Yakui.zhao <yakui.zhao@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.
Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: Len Brown <len.brown@intel.com>
|
