| Age | Commit message (Collapse) | Author |
|---|
|
Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.
v2:
- enable only when needed IORDY
- use dev_get_drvdata
v3:
- add missing clk_put() calls
- use platform_get_irq()
- fix resume code to avoid disabling IORDY on resume
v4:
- Remove EXPERIMENTAL and switch to depends on ARCH_MXC
- Use devm_kzalloc()
- make clock a must-have
- Use only 1 ioremap
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.
Currently driver supports only True IDE mode.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Add support for Acard ATP8620 host controller.
Based upon initial version by Jeff Garzik.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Move the Kconfig entry to the proper location as needed since
9a7780c9acb821fe1c2b6fc53f74cc2556ff5364 (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Changed <module>-objs to <module>-y in Makefile.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/mm/Kconfig
|
|
Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch enables the on-chip DWC SATA controller of the AppliedMicro
processor 460EX.
Signed-off-by: Rupjyoti Sarmah <rsarmah@appliedmicro.com>
Signed-off-by: Mark Miesfeld <mmiesfeld@appliedmicro.com>
Signed-off-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones. Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.
ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.
This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced. Either way, the size difference is insignificant. This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This can be used for AHCI-compatible interfaces implemented inside
System-On-Chip solutions, or AHCI devices connected via localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch should contain no functional changes, just moves code
around.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Conflicts:
include/linux/kvm.h
|
|
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.
The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
From: Alan Cox <alan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch provides PATA driver for CompactFlash interface in True IDE
mode on AT91SAM9260 SoC.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Support for Palm LifeDrive's internal harddrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch adds Intel SCH chipsets (AF82US15W, AF82US15L, AF82UL11L)
PATA controller support.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set. PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts. This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Now that SFF support is completely separated out from the core layer,
it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers
depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled. This saves good
number of bytes for small systems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This driver nicely wraps around pata_platform library functions,
and provides OF platform bus bindings to the PATA devices.
Also add || PPC to the PATA_PLATFORM's "depends on" Kconfig entry,
needed for PA Semi Electra.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds support for Freescale 3.0Gbps SATA Controller supporting
Native Command Queueing(NCQ), device hotplug, and ATAPI. This controller
can be found on MPC8315 and MPC8378.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
On a cable there may be
eighty wires or perhaps forty
and we learn about its type
In the world of ACPI
So we call the GTM
And we find the the timing rate
And we look through it to see
If eighty wire it must be
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
And the drivers last you see
Picking up unknown pci ids
and the code begins to work
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
[Full speed ahead, Mr Hacker, full speed ahead]
Full speed over here sir!
Checking Cable, checking cable
Aye aye, 80 wire,
Heaven heaven]
If we use ACPI (ACPI)
Every box (every box) has all we need (has all we need)
Cable type (cable type) and mode timing (mode timing)
In our ATA (in our ATA) subroutines (subroutines, ha ha)
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Implement Port Multiplier support. To support PMP, a LLDD has to
supply ops->pmp_read() and pmp_write(). If non-null, ->pmp_attach and
->pmp_detach are called on PMP attach and detach, respectively.
->pmp_read/write() can be called while the port is frozen, so they
must be implemented by polling. This patch supplies several helpers
to ease ->pmp_read/write() implementation.
Also, irq_handler and error_handler must be PMP aware. Most of PMP
aware EH can be done by calling ata_pmp_do_eh() with appropriate
methods. PMP EH uses separate set of reset methods and this patch
implements standard prereset, hardreset and postreset methods.
This patch only implements PMP support. The next patch will integrate
PMP into the reset of libata and thus enable PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
[plus SuperIO fixes by Kyle McMartin]
[plus a cleanup from me]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)
The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.
When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix all issues pointed out in Jeff's email.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ACPI applies to both SATA and PATA. Drop the 'S' from the config
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (82 commits)
[ARM] Add comments marking in-use ptrace numbers
[ARM] Move syscall saving out of the way of utrace
[ARM] 4360/1: S3C24XX: regs-udc.h remove unused macro
[ARM] 4358/1: S3C24XX: mach-qt2410.c: remove linux/mmc/protocol.h header
[ARM] mm 10: allow memory type to be specified with ioremap
[ARM] mm 9: add additional device memory types
[ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6
[ARM] iop: add missing parens in macro
[ARM] mm 7: remove duplicated __ioremap() prototypes
ARM: OMAP: fix OMAP1 mpuio suspend/resume oops
ARM: OMAP: MPUIO wake updates
ARM: OMAP: speed up gpio irq handling
ARM: OMAP: plat-omap changes for 2430 SDP
ARM: OMAP: gpio object shrinkage, cleanup
ARM: OMAP: /sys/kernel/debug/omap_gpio
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
ARM: OMAP: Enable 24xx GPIO autoidling
[ARM] 4318/2: DSM-G600 Board Support
[ARM] 4227/1: minor head.S fixups
[ARM] 4328/1: Move i.MX UART regs to driver
...
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Support for the PCI CMD640 (not VLB)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is the patch for PATA controller of Celleb.
This driver uses the managed iomap (devres).
Because this driver needs special taskfile accesses, there is
a copy of ata_std_softreset(). ata_dev_try_classify() is exported
so that it can be used in this function.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
_GTF is an acpi method that is used to reinitialize the drive. It returns
a task file containing ata commands that are sent back to the drive to restore
it to boot up defaults.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(cherry picked from 9c69cab24b51a89664f4c0dfaf8a436d32117624 commit)
|
|
Driver for Initio 162x SATA controllers. ATA r/w, ATAPI r, hotplug
and suspend/resume work. ATAPI w (recording, that is) broken. Feel
free to fix it, but be warned, this controller is weird.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds initial libata support for the Freescale
MPC5200 integrated IDE controller.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add a driver for the IT8213 which is a single channel ICH-ish PATA
controller. As it is very different to the IT8211/2 it gets its own
driver. There is a legacy drivers/ide driver also available and I'll post
that once I get time to test it all out (probably early January). If
anyone else needs the drivers/ide driver and wants to do the merge for
drivers/ide (Bart ??) then I'll forward it.
[akpm@osdl.org: add PCI ID, constify needed_pio[]]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
needs a changelog
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is a legacy mode PATA driver for the 6101/45 and will also drive
the SATA ports 1 & 2 in legacy mode as well if desired. Tested and
confirmed working by users. The chip supports AHCI type behaviour for
SATA and has a more advanced PATA interface as well so this driver will
get it working but not get best performance for now.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Winbond 83759A support in non-multichip mode (afaik nobody ever used
multichip mode anyway). The 83759 is not supported by this driver as it
is already handled elsewhere and doens't use the same interfaces.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
