summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_pdc202xx_old.c
AgeCommit message (Collapse)Author
2007-03-06pata_pdc202xx_old: fix data corruption and other problemsBartlomiej Zolnierkiewicz
Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}() They were broken for all configurations except one (master device on primary channel, no other devices) and as a result device settings + PIO/DMA timings were being programmed into the wrong PCI registers. This could result in a large variety of problems including data corruption, hangs etc. (depending on devices used and your luck :-). ap->port_no ap->devno used PCI registers correct PCI registers 0 0 0x60-0x62 0x60-0x62 0 1 0x62-0x64 0x64-0x66 1 0 0x64-0x66 0x68-0x6a 1 1 0x66-0x68 0x6c-0x6e Also forward port recent fixes from drivers/ide pdc202xx_old driver: * fix XFER_MW_DMA0 timings (they were overclocked, use the official ones) * fix bitmasks for clearing bits of register B: - when programming DMA mode bit 0x10 of register B was cleared which resulted in overclocked PIO timing setting (iff PIO0 was used) - when programming PIO mode bits 0x18 weren't cleared so suboptimal timings were used for PIO1-4 if PIO0 was previously set (bit 0x10) and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08) and finally bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-02libata: add missing CONFIG_PM in LLDsTejun Heo
Add missing #ifdef CONFIG_PM conditionals around all PM related parts in libata LLDs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26[libata] bump versionsJeff Garzik
Bump versions based on changes submitted during 2.6.21 merge window. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: add another IRQ calls (libata drivers)Akira Iguchi
This patch is against each libata driver. Two IRQ calls are added in ata_port_operations. - irq_on() is used to enable interrupts. - irq_ack() is used to acknowledge a device interrupt. In most drivers, ata_irq_on() and ata_irq_ack() are used for irq_on and irq_ack respectively. In some drivers (ex: ahci, sata_sil24) which cannot use them as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: convert to iomapTejun Heo
Convert libata core layer and LLDs to use iomap. * managed iomap is used. Pointer to pcim_iomap_table() is cached at host->iomap and used through out LLDs. This basically replaces host->mmio_base. * if possible, pcim_iomap_regions() is used Most iomap operation conversions are taken from Jeff Garzik <jgarzik@pobox.com>'s iomap branch. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: update libata LLDs to use devresTejun Heo
Update libata LLDs to use devres. Core layer is already converted to support managed LLDs. This patch simplifies initialization and fixes many resource related bugs in init failure and detach path. For example, all converted drivers now handle ata_device_add() failure gracefully without excessive resource rollback code. As most resources are released automatically on driver detach, many drivers don't need or can do with much simpler ->{port|host}_stop(). In general, stop callbacks are need iff port or host needs to be given commands to shut it down. Note that freezing is enough in many cases and ports are automatically frozen before being detached. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09libata: kill qc->nsect and cursectTejun Heo
libata used two separate sets of variables to record request size and current offset for ATA and ATAPI. This is confusing and fragile. This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and kills them. Also, ata_pio_sector() is updated to use bytes for qc->cursg_ofs instead of sectors. The field used to be used in bytes for ATAPI and in sectors for ATA. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-03[PATCH] libata: kill unnecessary sht->max_sectors initializationsTejun Heo
sht->max_sectors is overrided unconditionally in ->slave_configure. There's no reason to set it to any value. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-12-01[PATCH] pata : more drivers that need only standard suspend and resumeAlan
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01[PATCH] pdc202xx_old: Fix name clashes with PA-RISCAlan Cox
pdc_* functions are part of the global namespace for the PDC on PA-RISC systems and this means our choice of pdc_ causes collisions between the PDC globals and our static functions. Rename them to pdc202xx where they are for both 2024x and 2026x. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-29[PATCH] libata: add missing sht->slave_destroyTejun Heo
Many LLDs are missing sht->slave_destroy. The method is mandatory to support device warm unplugging (echo 1 > /sys/.../delete). Without it, libata might access released scsi device. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-09-28[libata] PCI ID table cleanup in various driversJeff Garzik
* Use PCI_VDEVICE() macro * const-ify pci_device_id table * standardize list terminator as "{ }" * convert spaces to tab in pci_driver struct (Alan-ism) * various minor whitespace cleanups Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-31[libata #pata-drivers] Trim trailing whitespace.Jeff Garzik
2006-08-29[libata] Add a bunch of PATA drivers.Jeff Garzik
The vast majority of drivers and changes are from Alan Cox. Albert Lee contributed and maintains pata_pdc2027x. Adrian Bunk, Andrew Morton, and Tejun Heo contributed various minor fixes and updates. Signed-off-by: Jeff Garzik <jeff@garzik.org>