| Age | Commit message (Collapse) | Author |
|---|
|
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Little fixlets, that the build started erroring / warning about:
drivers/ata/pata_scc.c: In function 'scc_bmdma_status':
drivers/ata/pata_scc.c:734: error: structure has no member named 'active_tag'
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:866: warning: passing arg 1 of 'ata_std_prereset' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:908: warning: passing arg 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 5 of 'ata_bmdma_drive_eh' from incompatible pointer type
make[2]: *** [drivers/ata/pata_scc.o] Error 1
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: Alan Cox <alan@redhat.com>
Cc: Mel Gorman <mel@skynet.ie>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument. @present indicates whether the device seems present during
reset. It's the result of TF access during softreset and link
onlineness during hardreset. @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump the versions for drivers that were modified, but had not already
had a version number bump.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data. As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.
pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes some issues of the previous patch:
- Use mode_filter() hook to limit ATAPI UDMA mode
- "data loss" warning message
- handling of udma_mask
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It seems irq_on() in ata_bus_reset() and ata_std_postreset()
are leftover of the EDD reset. Remove them.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The commit d4b2bab4f26345ea1803feb23ea92fbe3f6b77bc added deadline support
to prereset and reset methods to libbata the pata_scc driver wasn't
converted. This patch is a naive attempt to bring this driver up to
scratch.
Build failures are:
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:870: error: too few arguments to function 'ata_std_prereset'
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:916: warning: passing argument 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:916: warning: passing argument 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:871: warning: control reaches end of non-void function
On a releated note scc_bus_post_reset() is (AFACT) identical to
ata_bus_post_reset(), would a patch to make ata_bus_post_reset() assesable
to drivers be accepted?
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert pdc_adma, pata_cs5520, pata_isapnp, pata_ixp4xx_cf,
pata_legacy, pata_mpc52xx, pata_mpiix, pata_pcmcia, pata_pdc2027x,
pata_platform, pata_qdi, pata_scc and pata_winbond to new init model.
* init_one()'s now follow more consistent init order
* cs5520 now registers one host with two ports, not two hosts. If any
of the two ports are disabled, it's made dummy as other drivers do.
Tested pdc_adma and pata_legacy. Both are as broken as before. The
rest are compile tested only.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
No code changes.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Merge order left libata-acpi and pata_scc with remainling usage of
ap->id. Kill superflous id printing and substitute the remaining ones
with ap->print_id.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is the patch for PATA controller of Celleb.
This driver uses the managed iomap (devres).
Because this driver needs special taskfile accesses, there is
a copy of ata_std_softreset(). ata_dev_try_classify() is exported
so that it can be used in this function.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
