summaryrefslogtreecommitdiffstats
path: root/drivers/ata/sata_nv.c
AgeCommit message (Collapse)Author
2008-10-10Merge branch 'upstream-2.6.28' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs libata-eh: clear UNIT ATTENTION after reset ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list libata: reorder ata_device to remove 8 bytes of padding on 64 bits [libata] pata_bf54x: Add proper PM operation pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC libata: Implement disk shock protection support [libata] Introduce ata_id_has_unload() PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver ata_piix: drop merged SCR access and use slave_link instead libata: implement slave_link libata: misc updates to prepare for slave link libata: reimplement link iterator libata: make SCR access ops per-link
2008-09-29libata: make SCR access ops per-linkTejun Heo
Logically, SCR access ops should take @link; however, there was no compelling reason to convert all SCR access ops when adding @link abstraction as there's one-to-one mapping between a port and a non-PMP link. However, that assumption won't hold anymore with the scheduled addition of slave link. Make SCR access ops per-link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29sata_nv: reinstate nv_hardreset() for non generic controllersTejun Heo
Commit 2fd673ecf0378ddeeeb87b3605e50212e0c0ddc6 which tried to remove hardreset for generic accidentally removed it for all flavors as all others were inheriting from nv_generic_ops. This patch reinstates nv_hardreset() and puts it into nv_common_ops which all flavors inherit from. nv_generic_ops now inherits from nv_common_ops and overrides .hardreset to ATA_OP_NULL. While at it, explain why nv_hardreset and ATA_OP_NULL override are necessary. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08sata_nv: disable hardreset for genericTejun Heo
of them being unifying probing, hotplug and EH reset paths uniform. Previously, broken hardreset could go unnoticed as it wasn't used during probing but when something goes wrong or after hotplug the problem will surface and bite hard. OSDL bug 11195 reports that sata_nv generic flavor falls into this category. Hardreset itself succeeds but PHY stays offline after hardreset. I tried longer debounce timing but the result was the same. http://bugzilla.kernel.org/show_bug.cgi?id=11195 So, it seems we'll have to drop hardreset from the generic flavor. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_nv: make hardreset return -EAGAIN on successTejun Heo
sata_nv hardreset can't classify but was left out while unifying follow-up SRST request mechanism[1]. This caused detection failures on those controllers. Fix it. Reported and bisected by Roland Dreier, Petr Vandrovec and Marc Dionne. Thanks guys. [1] 305d2a1ab137d11d573319c315748a87060fe82d Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Roland Dreier <rdreier@cisco.com> Cc: Petr Vandrovec <vandrove@vc.cvut.cz> Cc: Marc Dionne <marc.c.dionne@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17libata: rename SFF port opsTejun Heo
Add sff_ prefix to SFF specific port ops. This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames ops and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17[libata] sata_nv: disable ADMA by defaultJeff Garzik
Continues to have open issues, and engineering support is extremely difficult to come by, according to fellow NVIDIA engineers. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17ata: SWNCQ should be enabled by defaultZoltan Boszormenyi
Signed-off-by: Zoltan Boszormenyi <zboszor@dunaweb.hu> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17libata: make reset related methods proper port operationsTejun Heo
Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: kill port_info->sht and ->irq_handlerTejun Heo
libata core layer doesn't care about sht or ->irq_handler. Those are only of interest to the LLD during initialization. This is confusing and has caused several drivers to have duplicate unused initializers for these fields. Currently only sata_nv uses these fields. Make sata_nv use ->private_data, which is supposed to carry LLD-specific information, instead and kill ->sht and ->irq_handler. nv_pi_priv structure is defined and struct literals are used to initialize private_data. Notational overhead is negligible. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use ops inheritanceTejun Heo
libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: implement and use SHT initializersTejun Heo
libata lets low level drivers build scsi_host_template and register it to the SCSI layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This patch implements SHT initializers which can be used to initialize all the boilerplate entries in a sht. Three variants of them are implemented - BASE, BMDMA and NCQ - for different types of drivers. Note that entries can be overriden by putting individual initializers after the helper macro. All sht tables are identical before and after this patch. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: normalize port_info, port_operations and sht tablesTejun Heo
Over the time, port info, ops and sht structures developed quite a bit of inconsistencies. This patch updates drivers. * Enable/disable_pm callbacks added to all ahci ops tables. * Every driver for SFF controllers now uses ata_sff_port_start() instead of ata_port_start() unless the driver has custom implementation. * Every driver for SFF controllers now uses ata_pci_default_filter() unless the driver has custom implementation. * Removed an odd port_info->sht initialization from ata_piix.c. Likely a merge byproduct. * A port which has ATA_FLAG_SATA set doesn't need to set cable_detect to ata_cable_sata(). Remove it from via and mv port ops. * Some drivers had unnecessary .max_sectors initialization which is ignored and was missing .slave_destroy callback. Fixed. * Removed unnecessary sht initializations port_info's. * Removed onsolete scsi device suspend/resume callbacks from pata_bf54x. * No reason to set ata_pci_default_filter() and bmdma functions for PIO-only drivers. Remove those callbacks and replace ata_bmdma_irq_clear with ata_noop_irq_clear. * pata_platform sets port_start to ata_dummy_ret0. port_start can just be set to NULL. * sata_fsl supports NCQ but was missing qc_defer. Fixed. * pata_rb600_cf implements dummy port_start. Removed. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: kill ATA_LFLAG_HRST_TO_RESUMETejun Heo
Now that hardreset is the preferred method of resetting, there's no need for ATA_LFLAG_HRST_TO_RESUME flag. Kill it. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17libata: prefer hardresetTejun Heo
When both soft and hard resets are available, libata preferred softreset till now. The logic behind it was to be softer to devices; however, this doesn't really help much. Rationales for the change: * BIOS may freeze lock certain things during boot and softreset can't unlock those. This by itself is okay but during operation PHY event or other error conditions can trigger hardreset and the device may end up with different configuration. For example, after a hardreset, previously unlockable HPA can be unlocked resulting in different device size and thus revalidation failure. Similar condition can occur during or after resume. * Certain ATAPI devices require hardreset to recover after certain error conditions. On PATA, this is done by issuing the DEVICE RESET command. On SATA, COMRESET has equivalent effect. The problem is that DEVICE RESET needs its own execution protocol. For SFF controllers with bare TF access, it can be easily implemented but more advanced controllers (e.g. ahci and sata_sil24) require specialized implementations. Simply using hardreset solves the problem nicely. * COMRESET initialization sequence is the norm in SATA land and many SATA devices don't work properly if only SRST is used. For example, some PMPs behave this way and libata works around by always issuing hardreset if the host supports PMP. Like the above example, libata has developed a number of mechanisms aiming to promote softreset to hardreset if softreset is not going to work. This approach is time consuming and error prone. Also, note that, dependingon how you read the specs, it could be argued that PMP fan-out ports require COMRESET to start operation. In fact, all the PMPs on the market except one don't work properly if COMRESET is not issued to fan-out ports after PMP reset. * COMRESET is an integral part of SATA connection and any working device should be able to handle COMRESET properly. After all, it's the way to signal hardreset during reboot. This is the most used and recommended (at least by the ahci spec) method of resetting devices. So, this patch makes libata prefer hardreset over softreset by making the following changes. * Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is now only used to tell prereset whether soft or hard reset will be issued. * Strip out now unneeded promote-to-hardreset logics from ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and other places. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-02-06sata_nv: fix ATAPI issues with memory over 4GB (v7)Robert Hancock
This fixes some problems with ATAPI devices on nForce4 controllers in ADMA mode on systems with memory located above 4GB. We need to delay setting the 64-bit DMA mask until the PRD table and padding buffer are allocated so that they don't get allocated above 4GB and break legacy mode (which is needed for ATAPI devices). Also, if either port is in ATAPI mode we need to set the DMA mask for the PCI device to 32-bit to ensure that the IOMMU code properly bounces requests above 4GB, as it appears setting the bounce limit does not guarantee that we will not try to map requests above this point. Reported to fix https://bugzilla.redhat.com/show_bug.cgi?id=351451 Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-01sata_nv: fix for completion handlingRobert Hancock
This patch is based on an original patch from Kuan Luo of NVIDIA, posted under subject "fixed a bug of adma in rhel4u5 with HDS7250SASUN500G". His description follows. I've reworked it a bit to avoid some unnecessary repeated checks but it should be functionally identical. "The patch is to solve the error message "ata1: CPB flags CMD err, flags=0x11" when testing HDS7250SASUN500G in rhel4u5. I tested this hd in 2.6.24-rc7 which needed to remove the mask in blacklist to run the ncq and the same error also showed up. I traced the bug and found that the interrupt finished a command (for example, tag=0) when the driver got that adma status is NV_ADMA_STAT_DONE and cpb->resp_flags is NV_CPB_RESP_DONE. However, For this hd, the drive maybe didn't clear bit 0 at this moment. It meaned the hardware had not completely finished the command. If at the same time the driver freed the command(tag 0) and sended another command (tag 0), the error happened. The notifier register is 32-bit register containing notifier value. Value is bit vector containing one bit per tag number (0-31) in corresponding bit positions (bit 0 is for tag 0, etc). When bit is set then ADMA indicates that command with corresponding tag number completed execution. So i added the check notifier code. Sometimes i saw that the notifier reg set some bits , but the adma status set NV_ADMA_STAT_CMD_COMPLETE ,not NV_ADMA_STAT_DONE. So i added the NV_ADMA_STAT_CMD_COMPLETE check code." Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: convert to chained sgTejun Heo
libata used private sg iterator to handle padding sg. Now that sg can be chained, padding can be handled using standard sg ops. Convert to chained sg. * s/qc->__sg/qc->sg/ * s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg entry. There need to be two extra sg entries. The renaming is also for future addition of other extra sg entries. * Padding setup is moved into ata_sg_setup_extra() which is organized in a way that future addition of other extra sg entries is easy. * qc->orig_n_elem is unused and removed. * qc->n_elem now contains the number of sg entries that LLDs should map. qc->mapped_n_elem is added to carry the original number of mapped sgs for unmapping. * The last sg of the original sg list is used to chain to extra sg list. The original last sg is pointed to by qc->last_sg and the content is stored in qc->saved_last_sg. It's restored during ata_sg_clean(). * All sg walking code has been updated. Unnecessary assertions and checks for conditions the core layer already guarantees are removed. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04sata_nv: don't use legacy DMA in ADMA mode (v3)Robert Hancock
We need to run any DMA command with result taskfile requested in ADMA mode when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine in ADMA mode which is not allowed. Enforce this with BUG_ON() since data corruption could potentially result if this happened. Also, fail any attempt to try and issue NCQ commands with result taskfile requested, since the hardware doesn't allow this. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08nv_hardreset: update dangling reference to bugzilla entryFernando Luis Vázquez Cao
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-29[libata] sata_nv: fix SWNCQ enablingJeff Garzik
Adapted from patches by Kuan Lou @ NVIDIA and Bartlomiej Zolnierkiewicz. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29[libata] Address some checkpatch-spotted issuesJeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29[libata] fix 'if(' and similar areas that lack whitespaceJeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-25[libata] sata_nv: SWNCQ should not apply to MCP61Kuan Luo
The mcp61 has bug with ncq. Signed-off-by: Kuan Luo <kluo@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-23[libata] checkpatch-inspired cleanupsJeff Garzik
Tackle the relatively sane complaints of checkpatch --file. The vast majority is indentation and whitespace changes, the rest are * #include fixes * printk KERN_xxx prefix addition * BSS/initializer cleanups Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-15[libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61Kuan Luo
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA controller. NCQ function is disable by default, you can enable it with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on MCP51 or MCP55 rev 0xa2 platform. [akpm@linux-foundation.org: build fix] Signed-off-by: Kuan Luo <kluo@nvidia.com> Signed-off-by: Peer Chen <pchen@nvidia.com> Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-12libata-pmp-prep: implement ops->qc_defer()Tejun Heo
Controllers which support PMP have various restrictions on which combinations of commands are allowed to what number of devices concurrently. This patch implements ops->qc_defer() which determines whether a qc can be issued at the moment or should be deferred. If the function returns ATA_DEFER_LINK, the qc will be deferred until a qc completes on the link. If ATA_DEFER_PORT, until a qc completes on any link. The defer conditions are advisory and in general ATA_DEFER_LINK can be considered as lower priority deferring than ATA_DEFER_PORT. ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and sata_sil24 are converted to use ata_std_qc_defer(). ops->qc_defer() is heavier than the original mechanism because full qc is prepped before determining to defer it, but various information is needed to determine defer conditinos and fully translating a qc is the only way to supply such information in generic manner. IMHO, this shouldn't cause any noticeable performance issues as * for most cases deferring occurs rarely (except for NCQ-aware cmd-switching PMP) * translation itself isn't that expensive * once deferred the command won't be repeated until another command completes which usually is a very long time cpu-wise. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->port_disable() hookJeff Garzik
It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik
* ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: make two port flags HRST_TO_RESUME and SKIP_D2H_BSY link flagsTejun Heo
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to ata_link->flags. This will allow host and PMP links to have different attributes. ata_port_info->link_flags is added and used by LLDs to specify these flags during initialization. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: linkify resetTejun Heo
Make reset methods and related functions deal with ata_link instead of ata_port. * ata_do_reset() * ata_eh_reset() * all prereset/reset/postreset methods and related functions This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: introduce ata_linkTejun Heo
Introduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link. This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port. This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31[libata] Bump driver versionsJeff Garzik
Bump the versions for drivers that were modified, but had not already had a version number bump. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: make ->scr_read/write callbacks return error codeTejun Heo
Convert ->scr_read/write callbacks to return error code to better indicate failure. This will help handling of SCR_NOTIFICATION. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: improve EH report formattingTejun Heo
Requiring LLDs to format multiple error description messages properly doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc() insert ", " on each invocation. __ata_ehi_push_desc() is the raw version without the automatic separator. While at it, make ehi_desc interface proper functions instead of macros. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10libata: simplify PCI legacy SFF host handlingTejun Heo
With PCI resource fix up for legacy hosts. We can use the same code path to allocate IO resources and initialize host for both legacy and native SFF hosts. Only IRQ requesting needs to be different. Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all legacy specific functions and use the renamed functions instead. This simplifies code a lot. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-02[libata] sata_nv: undo merge errorJeff Garzik
Only the ADMA entry was supposed to be able to change queue depth. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-02sata_nv: allow changing queue depthRobert Hancock
The sata_nv driver was missing the change_queue_depth hook in the SCSI host template which the other NCQ-capable libata drivers had. This made it impossible to change the queue depth by user request. Add this in. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21libata: bump versionsJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21libata: Trim trailing whitespaceJeff Garzik
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17sata_nv: fix fallout of devres conversionTejun Heo
As with all other drivers, sata_nv's hpriv is allocated with devm_kzalloc() and there's no need to free it explicitly. Kill nv_remove_one() which incorrectly used kfree() instead of devm_kfree() and use ata_pci_remove_one() directly. Original fix is from Peer Chen. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17drivers/ata: remove the wildcard from sata_nv driverPeer Chen
Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv driver is unnecessary. Also the wildcard sometimes cause sata_nv driver to be loaded for AHCI controllers,which is not as expected. Signed-off-by: Peer Chen <pchen@nvidia.com> Cc: Tejun Heo <htejun@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11libata: clean up SFF init messTejun Heo
The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11libata: reimplement suspend/resume support using sdev->manage_start_stopTejun Heo
Reimplement suspend/resume support using sdev->manage_start_stop. * Device suspend/resume is now SCSI layer's responsibility and the code is simplified a lot. * DPM is dropped. This also simplifies code a lot. Suspend/resume status is port-wide now. * ata_scsi_device_suspend/resume() and ata_dev_ready() removed. * Resume now has to wait for disk to spin up before proceeding. I couldn't find easy way out as libata is in EH waiting for the disk to be ready and sd is waiting for EH to complete to issue START_STOP. * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config(). This fixes spindown on shutdown and suspend-to-disk. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09sata_nv: fix ADMA freeze/thaw/irq_clear issuesRobert Hancock
This patch fixes some problems with ADMA-capable controllers with regard to freeze, thaw and irq_clear libata callbacks. Freeze and thaw didn't switch the ADMA-specific interrupts on or off, and more critically the irq_clear function didn't respect the restriction that the notifier clear registers for both ports have to be written at the same time even when only one port is being cleared. This could result in timeouts on one port when error handling (i.e. as a result of hotplug) occurred on the other port. As well, this fixes some issues in the interrupt handler: we shouldn't check any ADMA status if the port has ADMA switched off because of an ATAPI device, and it also checks to see if any ADMA interrupt has been raised even when we are in port-register mode. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-01libata: add deadline support to prereset and reset methodsTejun Heo
Add @deadline to prereset and reset methods and make them honor it. ata_wait_ready() which directly takes @deadline is implemented to be used as the wait function. This patch is in preparation for EH timing improvements. * ata_wait_ready() never does busy sleep. It's only used from EH and no wait in EH is that urgent. This function also prints 'be patient' message automatically after 5 secs of waiting if more than 3 secs is remaining till deadline. * ata_bus_post_reset() now fails with error code if any of its wait fails. This is important because earlier reset tries will have shorter timeout than the spec requires. If a device fails to respond before the short timeout, reset should be retried with longer timeout rather than silently ignoring the device. There are three behavior differences. 1. Timeout is applied to both devices at once, not separately. This is more consistent with what the spec says. 2. When a device passes devchk but fails to become ready before deadline. Previouly, post_reset would just succeed and let device classification remove the device. New code fails the reset thus causing reset retry. After a few times, EH will give up disabling the port. 3. When slave device passes devchk but fails to become accessible (TF-wise) after reset. Original code disables dev1 after 30s timeout and continues as if the device doesn't exist, while the patched code fails reset. When this happens, new code fails reset on whole port rather than proceeding with only the primary device. If the failing device is suffering transient problems, new code retries reset which is a better behavior. If the failing device is actually broken, the net effect is identical to it, but not to the other device sharing the channel. In the previous code, reset would have succeeded after 30s thus detecting the working one. In the new code, reset fails and whole port gets disabled. IMO, it's a pathological case anyway (broken device sharing bus with working one) and doesn't really matter. * ata_bus_softreset() is changed to return error code from ata_bus_post_reset(). It used to return 0 unconditionally. * Spin up waiting is to be removed and not converted to honor deadline. * To be on the safe side, deadline is set to 40s for the time being. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28libata: convert ata_pci_init_native_mode() users to new init modelTejun Heo
Convert drivers which use ata_pci_init_native_mode() to new init model. ata_pci_init_native_host() is used instead. sata_nv, sata_uli and sata_sis are in this category. Tested on nVidia Corporation CK804 Serial ATA Controller [10de:0054] in both BMDMA and ADMA mode. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28sata_nv: don't read shadow registers when in ADMA modeRobert Hancock
Reading from the ATA shadow registers while we are in ADMA mode may cause undefined behavior. Don't read the ATA status register when completing commands for this reason, it shouldn't be needed as the controller will notify us if the command failed. Also, don't allow commands with result taskfile requested to execute in ADMA mode, since that requires accessing the shadow registers. We also still need to override tf_read since libata will read the result taskfile on a command failure, and we need to go into port register mode before allowing this. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-09sata_nv: revert use of notifiers for nowRobert Hancock
Commit 721449bf0d51213fe3abf0ac3e3561ef9ea7827a added support for using the ADMA notifier bits to determine which commands to check for completion. However there have been reports that this causes command timeouts in certain cases. This is still being investigated. In addition, apparently the notifiers won't work if ADMA is disabled on the other port as a result of an ATAPI device being connected, and we don't handle this case properly. For now, just restore the previous behavior of checking all active commands to see if they are complete, without relying on the notifiers. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>