| Age | Commit message (Collapse) | Author |
|---|
|
By default, the PATA pins are routed to the async address lines in which
case, no peripheral muxing needs to be done. However, if the pins get
routed through the GPIO PORTs pins, we need to make sure to request them
so that the muxing is properly set up.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected. This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.
The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This reverts commit d43744390e460dce6626fb8de2c02a24ff650005, because
it breaks the boot on several machines (mostly sparc64, at present).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: remove pointless NULL test
pata_hpt3x2n: fix clock turnaround
libata: fix reporting of drained bytes when clearing DRQ
sata_mv: add power management support for the PCI controllers.
sata_mv: store the board_idx into the host private data
pata_octeon_cf: use resource_size(), to fix resource sizing bug
libata: use the WRITE_SAME_16 define
sata_mv: move the PCI bar description initialization code
sata_mv: add power management support for the platform driver
sata_mv: support clkdev framework
sata_mv: increase PIO IORDY timeout
Fixed crazy mode-change in merge.
|
|
Remove !ap test, where ap is guaranteed not-NULL. Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The clock turnaround code still doesn't work for several reasons:
- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
or updated, so the driver can only set the chip to the DPLL clock
mode, not the PCI mode;
- the driver doesn't serialize access to the channels depending on
the current clock mode like the vendor drivers, so the clock
turnaround is only executed "optionally", not always as it should be;
- the wrong ports are written to when hpt3x2n_set_clock() is called
for the secondary channel;
- hpt3x2n_set_clock() can inadvertently enable the disabled channels
when resetting the channel state machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This information will be used in the resume function.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
|
|
Conflicts:
include/linux/kvm.h
|
|
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.
The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
|
|
Conflicts:
kernel/irq/chip.c
|
|
This reverts commit f20941f334d8fdb6b598658979709b4e94cd034b.
Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second
argument will always "win" as a minimal one"
Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio(). The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."
Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
pcmcia: rework the irq_req_t typedef
pcmcia: remove deprecated handle_to_dev() macro
pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
pcmcia: remove unused "window_t" typedef
pcmcia: move some window-related code to pcmcia_ioctl.c
pcmcia: Change window_handle_t logic to unsigned long
pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
drivers/pcmcia: remove unnecessary kzalloc
pcmcia: correct handling for Zoomed Video registers in topic.h
pcmcia: fix printk formats
pcmcia: autoload module pcmcia
pcmcia/staging: update comedi drivers
PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
PCMCIA: ss: allow PCI IRQs > 255
PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
PCMCIA: soc_common: constify soc_pcmcia_socket ops member
PCMCIA: sa1111: remove duplicated initializers
PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
...
|
|
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Comment spelling fixes and whitespace adjustment.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
ata_set_lba_range_entries used the variable max for two different things
which was confusing. Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped. Report this value in the Block Limits
Maximum Unmap LBA count field.
If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Remove superfluous timings table entry while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
MWDMA0 timings cannot be met with the PIIX based controller
programming interface.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix register naming while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Call sis_fixup() on resume.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Set correct bits to switch between UDMA2 and UDMA4.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix ->resume method to do chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).
This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
[ port of Sergei's fixes for pata_efar from commit 5f33b3b ]
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble
Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).
There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.
Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Do not clear MWDMA timings for device on the other port when
programming slave device.
This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
