| Age | Commit message (Collapse) | Author |
|---|
|
* pm-domains:
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
PM / Domains: Provide an always on power domain governor
PM / Domains: Fix default system suspend/resume operations
PM / Domains: Make it possible to assign names to generic PM domains
PM / Domains: fix compilation failure for CONFIG_PM_GENERIC_DOMAINS unset
PM / Domains: Automatically update overoptimistic latency information
PM / Domains: Add default power off governor function (v4)
PM / Domains: Add device stop governor function (v4)
PM / Domains: Rework system suspend callback routines (v2)
PM / Domains: Introduce "save/restore state" device callbacks
PM / Domains: Make it possible to use per-device domain callbacks
|
|
Some devices, like the I2C controller on SH7372, are not
necessary for providing power to their children or forwarding
wakeup signals (and generally interrupts) from them. They are
only needed by their children when there's some data to transfer,
so they may be suspended for the majority of time and resumed
on demand, when the children have data to send or receive. For this
purpose, however, their power.ignore_children flags have to be set,
or the PM core wouldn't allow them to be suspended while their
children were active.
Unfortunately, in some situations it may take too much time to
resume such devices so that they can assist their children in
transferring data. For example, if such a device belongs to a PM
domain which goes to the "power off" state when that device is
suspended, it may take too much time to restore power to the
domain in response to the request from one of the device's
children. In that case, if the parent's resume time is critical,
the domain should stay in the "power on" state, although it still may
be desirable to power manage the parent itself (e.g. by manipulating
its clock).
In general, device PM QoS may be used to address this problem.
Namely, if the device's children added PM QoS latency constraints
for it, they would be able to prevent it from being put into an
overly deep low-power state. However, in some cases the devices
needing to be serviced are not the immediate children of a
"children-ignoring" device, but its grandchildren or even less
direct descendants. In those cases, the entity wanting to add a
PM QoS request for a given device's ancestor that ignores its
children will have to find it in the first place, so introduce a new
helper function that may be used to achieve that. This function,
dev_pm_qos_add_ancestor_request(), will search for the first
ancestor of the given device whose power.ignore_children flag is
set and will add a device PM QoS latency request for that ancestor
on behalf of the caller. The request added this way may be removed
with the help of dev_pm_qos_remove_request() in the future, like
any other device PM QoS latency request.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Make the runtime PM core use device PM QoS constraints to check if
it is allowed to suspend a given device, so that an error code is
returned if the device's own PM QoS constraint is negative or one of
its children has already been suspended for too long. If this is
not the case, the maximum estimated time the device is allowed to be
suspended, computed as the minimum of the device's PM QoS constraint
and the PM QoS constraints of its children (reduced by the difference
between the current time and their suspend times) is stored in a new
device's PM field power.max_time_suspended_ns that can be used by
the device's subsystem or PM domain to decide whether or not to put
the device into lower-power (and presumably higher-latency) states
later (if the constraint is 0, which means "no constraint", the
power.max_time_suspended_ns is set to -1).
Additionally, the time of execution of the subsystem-level
.runtime_suspend() callback for the device is recorded in the new
power.suspend_time field for later use by the device's subsystem or
PM domain along with power.max_time_suspended_ns (it also is used
by the core code when the device's parent is suspended).
Introduce a new helper function,
pm_runtime_update_max_time_suspended(), allowing subsystems and PM
domains (or device drivers) to update the power.max_time_suspended_ns
field, for example after changing the power state of a suspended
device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Make dev_pm_qos_add_request() use WARN() in a better way and do not hardcode
the function's name into the message (use __func__ instead).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Most of these files were implicitly getting EXPORT_SYMBOL via
device.h which was including module.h, but that path will be broken
soon.
[ with input from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
To read the current PM QoS value for a given device we need to
make sure that the device's power.constraints object won't be
removed while we're doing that. For this reason, put the
operation under dev->power.lock and acquire the lock
around the initialization and removal of power.constraints.
Moreover, since we're using the value of power.constraints to
determine whether or not the object is present, the
power.constraints_state field isn't necessary any more and may be
removed. However, dev_pm_qos_add_request() needs to check if the
device is being removed from the system before allocating a new
PM QoS constraints object for it, so make it use the
power.power_state field of struct device for this purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Add a global notification chain that gets called upon changes to the
aggregated constraint value for any device.
The notification callbacks are passing the full constraint request data
in order for the callees to have access to it. The current use is for the
platform low-level code to access the target device of the constraint.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Implement the per-device PM QoS constraints by creating a device
PM QoS API, which calls the PM QoS constraints management core code.
The per-device latency constraints data strctures are stored
in the device dev_pm_info struct.
The device PM code calls the init and destroy of the per-device constraints
data struct in order to support the dynamic insertion and removal of the
devices in the system.
To minimize the data usage by the per-device constraints, the data struct
is only allocated at the first call to dev_pm_qos_add_request.
The data is later free'd when the device is removed from the system.
A global mutex protects the constraints users from the data being
allocated and free'd.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
