| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor. Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Delete code which sets SCSI status incorrectly as it's already been set
correctly above this incorrect code. The bug was introduced in 2009 by
commit b0e15f6db111 ("cciss: fix typo that causes scsi status to be
lost.")
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Tested-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The total number of scatter gather elements in the CISS command
used by the scsi tape code was being cast to a u8, which can hold
at most 255 scatter gather elements. It should have been cast to
a u16. Without this patch the command gets rejected by the controller
since the total scatter gather count did not add up to the right
value resulting in an i/o error.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The default is too small (1024 blocks), use h->cciss_max_sectors (8192 blocks)
Without this change, if you try to set the block size of a tape drive above
512*1024, via "mt -f /dev/st0 setblk nnn" where nnn is greater than 524288,
it won't work right.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A long time ago, probably in 2002, one of the distros, or maybe more than
one, loaded block drivers prior to loading the SCSI mid layer. This meant
that the cciss driver, being a block driver, could not engage the SCSI mid
layer at init time without panicking, and relied on being poked by a
userland program after the system was up (and the SCSI mid layer was
therefore present) to engage the SCSI mid layer.
This is no longer the case, and cciss can safely rely on the SCSI mid
layer being present at init time and engage the SCSI mid layer straight
away. This means that users will see their tape drives and medium
changers at driver load time without need for a script in /etc/rc.d that
does this:
for x in /proc/driver/cciss/cciss*
do
echo "engage scsi" > $x
done
However, if no tape drives or medium changers are detected, the SCSI mid
layer will not be engaged. If a tape drive or medium change is later
hot-added to the system it will then be necessary to use the above script
or similar for the device(s) to be acceesible.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive. Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2. This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
corresponding deallocation"
This reverts commit 978eb516a4e1a1b47163518d6f5d5e81ab27a583.
The commit was broken, relying on other changes that have not been
committed yet.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
and fix a nearby typo, "do" that should have been "due"
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
deallocation
This bit got lost somewhere along the way. Without this, panic.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cciss: change printks to dev_warn, etc.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: separate cmd_alloc() and cmd_special_alloc()
cmd_alloc() took a parameter which caused it to either allocate
from a pre-allocated pool, or allocate using pci_alloc_consistent.
This parameter is always known at compile time, so this would
be better handled by breaking the function into two functions
and differentiating the cases by function names. Same goes
for cmd_free().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: use consistent variable names
"h", for the hba structure and "c" for the command structures.
and get rid of trivial CCISS_LOCK macro.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: Set the performant mode bit in the scsi half of the driver
In a couple of places, the performant mode bit wasn't being set in
the scsi half of the driver, causing commands to seem to hang. Use
enqueue_cmd_and_start_io() where appropriate. This fixes a bug that
echo engage scsi > /proc/driver/cciss/cciss0
would hang.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Remove a debug statement left behind by accident Ths debug statement got
left behind. It was commented out after use but not deleted.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add a mode of controller operation called Performant Mode. Even though
cciss has been deprecated in favor of hpsa there are new controllers due
out next year that HP must support in older vendor distros. Vendors
require all fixes/features be upstream. These new controllers support
only 16 commands in simple mode but support up to 1024 in performant mode.
This requires us to add this support at this late date.
The performant mode transport minimizes host PCI accesses by performinf
many completions per read. PCI writes are posted so the host can write
then immediately get off the bus not waiting for the writwe to complete to
the target. In the context of performant mode the host read out to a
controller pulls all posted writes into host memory ensuring the reply
queue is coherent.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
I moved the range check after the increment. The current code would
write past the end of the array once before calling BUG().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cciss: Fix problem with scatter gather elements in the scsi half of the driver
When support for more than 31 scatter gather elements was added to the block
half of the driver, the SCSI half of the driver was not addressed, and the bump
from 31 to 32 scatter gather elements in the command block itself (not chained)
actually broke the SCSI half of the driver, so that any transfer requiring 32
scatter gather elements wouldn't work. This fix also increases the max transfer
size and size of the scatter gather table to the limit supported by the controller
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
cciss: eliminate unnecessary pointer use in cciss scsi code
An extra level of indirection was being used in some places
for no real reason.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
cciss: do not use void pointer for scsi hba data
and get rid of related unnecessary type casting
and delete some superfluous and misleading comments nearby.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
cciss: detect bad alignment of scsi commands at build time
Incidentally fix some nearby c++ style comments.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
cciss: Fix weird usage of ENXIO in cciss_scsi.c
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
cciss: fix typo that causes scsi status to be lost.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Make SCSI reset error handler decode unit attention ASC
and after a target reset wait for a unit attention that indicates
a reset occurred rather than just for any old unit attention.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Change cciss scsi error handling routines to work with interrupts enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Simplify interfaces of sendcmd() and sendcmd_withirq() so that they
provide only one way to address commands instead of three ways.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Use schedule_timeout_uninterruptible instead of schedule_timeout in the
scsi error handling code when waiting between TUR polls since we are not
interested in nor want to be interrupted by signals.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Use schedule_timeout_interruptible() instead of open-coding the set and
schedule parts.
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Fix the SCSI reset error handler to send a working, properly addressed
reset message to the target device and add code to wait for the target
device to become ready by polling it with Test Unit Ready.
The existing reset code was broken in that it didn't bother to set the
8-byte LUN address to anything besides zero, so the command was addressed
to the controller, which pretended to the driver that the command
succeeded, while doing nothing. Ages ago I tested this code, but
unbeknownst to me, my test was flawed, and what I thought was a tape drive
getting reset was actually nothing of the sort. Unfortunately, there is
still lots of Smartarray firmware that doesn't handle doing target resets
right, and this code won't help in those cases, but it also shouldn't make
things worse in those cases than they already are.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Fix cciss SCSI rescan code to better notice device changes.
If you hot-unplug a tape drive, then hot-plug a different
tape drive into the same slot in a storage enclosure,
the cciss driver wouldn't notice anything had changed, as
it was only looking at the LUN address and device type.
Now it looks at the inquiry page 0x83 device identifier,
and vendor and model strings as well.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch adds support for multi-lun devices in a SAS environment. It's
required for the support of media changers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch changes way we notify the scsi layer that something has changed
on the SCSI tape side of the driver. The user can now just tell the driver
to rescan a particular controller rather than having to know the SCSI nexus
to echo into the SCSI mid-layer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
* Fix oops on cciss rmmod due to calling pci_free_consistent with
irqs disabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
volumes
This patch allows us to display information about all of the logical volumes
configured on a particular controller without stepping on memory even when
there are many volumes (128 or more) configured.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
This patch updates the copyright information for the cciss driver. It
includes extending the year to 2007 (how timely) and some minor corrections
deemed necessary by HP legal and the Open Source Review Board. Please
consider this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
--------------------------------------------------------------------------------
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mike Miller <Mike.Miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Make cciss unconditionally include scsi/scsi.h, because of the use of
SCSI_IOCTL_GET_IDLUN and SCSI_IOCTL_GET_BUS_NUMBER.
Signed-off-by: Stephen M. Cameron <steve.cameron@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Replace scsi_device_types array API with scsi_device_type function API.
Gets rid of a lot of common code, as well as being easier to use.
- Add the new device types in SPC4 r05a, and rename some of the older ones.
- Reformat the printing of inquiry data; now fits on one line and
includes PQ.
I think I've addressed all the feedback from the previous versions. My
current test box prints:
scsi 2:0:1:0: Direct access HP 18.2G ATLAS10K3_18_SCA HP05 PQ: 0 ANSI: 2
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions. Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH. Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
this patch converts drivers/block to kzalloc usage.
Compile tested with allyesconfig.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This creates a new function, cciss_interrupt_mode called from
cciss_pci_init. This function determines what type of interrupt vector to
use, i.e., MSI, MSI-X, or IO-APIC.
One noticeable difference is changing the interrupt field of the controller
struct to an array of 4 unsigned ints. The Smart Array HW is capable of
generating 4 distinct interrupts depending on the transport method in use
during operation. These are:
#define DOORBELL_INT 0
Used to notify the contoller of configuration updates. We only use
this feature when in polling mode.
#define PERF_MODE_INT 0
Used when the controller is in Performant Mode.
#define SIMPLE_MODE_INT 2
Used when the controller is in Simple Mode (current Linux implementation).
#define MEMQ_INT_MODE 3
Not used.
When using IO-APIC interrupts these 4 lines are OR'ed together so when any
one fires an interrupt an is generated. In MSI or MSI-X mode this hardware
OR'ing is ignored. We must register for our interrupt depending on what
mode the controller is running. For Linux we use SIMPLE_MODE_INT
exclusively at this time. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
drivers/block/cciss_scsi.c:264: warning: `print_bytes' defined but not used
drivers/block/cciss_scsi.c:298: warning: `print_cmd' defined but not used
Signed-off-by: Grant Coady <gcoady@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds SCSI error handling code to the SCSI portion
of the cciss driver.
Signed-off-by: Stephen M. Cameron <steve.cameron@hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
