Age | Commit message (Collapse) | Author |
|
The "Local READ/WRITE failed" messages are too verbose.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
using the global printk_ratelimit() may mask other messages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
"canceled" w_read_retry_remote never completed, if they have been
canceled after drbd_disconnect connection teardown cleanup has already
run (or we are currently not connected anyways).
Fixed by not queueing a remote retry if we already know it won't work
(pdsk not uptodate), and cleanup ourselves on "cancel", in case we hit a
race with drbd_disconnect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
drbd/drbd_receiver.c: linux/mm.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
It seems to improve performance if we allow the "p_data" header in its
own frame (no MSG_MORE), but sendpage all but the last page with MSG_MORE.
This is also in preparation of a later zero copy receive implementation.
Suggested by Eduard.Guzovsky@stratus.com on drbd-dev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
quoting tcp(7):
On individual connections, the socket buffer size must be set prior to the
listen(2) or connect(2) calls in order to have it take effect.
This adds a wrapper to do so, and uses it appropriately.
Improves performance in certain situations.
Note that because we cannot easily determine which socket will be
"meta" and wich "data" (bulk) socket, we adjust both sockets.
Previously, DRBD only adjusted the bufsizes of the "data" socket.
Thanks again to Eduard.Guzovsky@stratus.com.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
On Thu, Apr 29, 2010 at 04:00:50PM -0400, Eduard.Guzovsky@stratus.com
wrote on drbd-dev@lists.linbit.com
Subject: [Drbd-dev] DRBD small synchronous writes performance improvements
> 1. TCP_QUICKACK option is set incorrectly. The goal was force TCP to
> send and ACK as a "one time" event. Instead the code permanently sets
> connection in the QUICKACK mode.
He is right, we actually want to use an even val with TCP_QUICKACK.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The late-UUID writing is delayed until the next release.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Conflicts:
fs/ext3/fsync.c
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Introduced a few days ago:
commit 45bb912bd5ea4d2b3a270a93cbdf767a0e2df6f5
Author: Lars Ellenberg <lars.ellenberg@linbit.com>
Date: Fri May 14 17:10:48 2010 +0200
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Got introduces with
commit 0c3f34516e8c5a1a0ba3585a7777d32bbbdf4ecb
Author: Philipp Reisner <philipp.reisner@linbit.com>
Date: Mon May 17 16:10:43 2010 +0200
drbd: Create new current UUID as late as possible
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
The choice was to either delay creation of the new UUID until
IO got thawed or to delay it until the first IO request.
Both are correct, the later is more friendly to users of
dual-primary setups, that actually only write on one side.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
If we detect late (= after grabing mdev->req_lock) that IO got frozen, we
return 1 to generic_make_request(), which simply will retry to make a
request for that bio.
In the subsequent call of generic_make_request() into drbd_make_request_26()
we sleep in inc_ap_bio().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Now that the peer may handle multi-bio EEs,
we can ignore the peer's limit,
and concentrate on the limits of the local IO stack.
This is safe accross drbd protocol versions,
as our queue_max_sectors() will be adjusted accordingly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
this should allow for better background resync performance.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
This should allow for better performance if the lower level IO stack
of the peers differs in limits exposed either via the queue,
or via some merge_bvec_fn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
* Only send delay_probes with protocol 93 or newer
* drbd_send_delay_probes() is called only from worker context,
no atomic_t needed for delay_seq
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
* Mention P_DELAY_PROBE in the packet naming array
* Do not corrupt the mdev->data.work list in case the timer goes
off before delay_probe_work got handled by the worker
* Do not mod_timer() twice for a single delay_probe pair
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
In a setup with a high bandwidth and high latency network, eventually
involving deep queues in routers, it is beneficial to only fill those
queues up to an limited extend with resync data.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
To reasonably control resync speed over drbd-proxy connections,
drbd has to measure the current delay of packets transmitted over
the (possibly congested) data socket vs the meta-data socket.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Delay_probes are new packets in the DRBD protocol, which allow
DRBD to know the current delay packets have on the data socket.
(relative to the meta data socket)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
The "surplus" bits of the old (smaller) bitmap must be clean
in case of online-grow without resync.
Note: Reverted 67ae8b80d4a116ab3b7094eb3723506b20c06dff as
well, since the lines added by this patch are redundant. The
bits get set by the bm_set_surplus(b) call before that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
in the meantime
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Some wish to be notified of all instances of split brain, not just those that
go unresolved. The initial-split-brain handler is called to notify someone
upon detection of all split brain conditions even if auto-recovery policies
are configured.
Signed-off-by: Adam Gandelman <adam.gandelman@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
The condition does not fit the commend (I may well be Primary,
even if I lost the disk earlier and now the connection).
And this is catched below anyways, where it also gets logged.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Even if it should never happen if the peer does behave, we need to
double check, and not even attempt access beyond end of device.
It usually would be caught by lower layers, resulting in "IO error",
but may also end up in the internal meta data area.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
In case both nodes are "inconsistent", invalidate would
have started a resync anyways, without a chance to ever
succeed, just filling the logs with warning messages.
Simply disallow that state change,
re-using the SS_NO_UP_TO_DATE_DISK return value.
This also changes the corresponding error string to
"Need access to UpToDate Data" -- I found the
"Refusing to be Primary without at least one UpToDate disk"
answer misleading in some situations anyways.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Don't forget to drain the digest in case we cannot satisfy a
checksum based resync or online-verify request.
It would additionally cause a protocoll error,
dropping the connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
block_id may be ID_SYNCER,
as well as checksum based resync request magic, or online verify magic.
Let's just drop that ASSERT.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
commit e4f925e12ea5daaa9baf2dd5af9c4951721dae95
Author: Philipp Reisner <philipp.reisner@linbit.com>
Date: Wed Mar 17 14:18:41 2010 +0100
drbd: Do not upgrade state to Outdated if already Inconsistent
prevented the necessary state transition for attaching while connected
(Diskless -> Consistent respectively Outdated).
This is the fix for the fix.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
There was a race condition:
In a situation with a SyncSource+Primary and a SyncTarget+Secondary node,
and a resync dependency to some other device. After both nodes decided
to do the resync, the other device finishes its resync process.
At that time SyncSource already sent the P_SYNC_UUID packet, and
already updated its peer disk state to Inconsistent.
The SyncTarget node waits for the P_SYNC_UUID and sends a state packet
to report the resync dependency change. That packet still carries
a disk state of Outdated.
Impact:
If application writes come in, during that time on the Primary node,
those do not get replicated, and the out-of-sync counter gets increased.
=> The completion of resync is not detected on the primary node.
=> stalled.
Those blocks get resync'ed with the next resync, since the are get
marked as out-of-sync in the bitmap.
In order to fix this, we filter out that wrong state change in the
sanitize_state() function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
To document that we know about deprecation of proc_create,
even though we are not affected, as we don't use the ->data member,
open code proc_create_data(..., NULL);
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
fix regression introduced in 8.3.3:
commit a9b17323f2875f5d9b132c2b476a750bf44b10c7
Author: Lars Ellenberg <lars.ellenberg@linbit.com>
Date: Wed Aug 12 15:18:33 2009 +0200
out-of-spinlock completion of master bio
: (bio_rw(bio) == READA)
? read_completed_with_error
: read_ahead_completed_with_error;
is obviously not what was intended.
No one noticed because of
* page-cache at work,
* local RAIDs
Impact:
Failed local READs are not retried remotely,
but errored to upper layers, causing filesystems
to remount read-only, or worse.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|