summaryrefslogtreecommitdiffstats
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2012-08-06Bluetooth: add support for atheros 0489:e057Peng Chen
Add support for the AR3012 chip found on Fioxconn. usb-devices shows: T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 44 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e057 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: btusb: Add vendor specific ID (0a5c:21f4) BCM20702A0Manoj Iyer
Patch adds support for BCM20702A0 device id (0a5c:21f4). usb-devices after patch was applied: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21f4 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DF154D6 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) usb-devices before patch was applied: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21f4 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DF154D6 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Tested-by: Chris Gagnon <chris.gagnon@canonical.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Introduce a flags variable to Three-wire UART stateJohan Hedberg
This patch introduces a flags variable to the Three-wire UART state struct and converts the two existing bools in the struct into flags. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Improve Three-wire UART configuration handlingJohan Hedberg
The configuration request/response messages contain a configuration field which contains the sliding window size (amount of unacked reliable packets that can be pending). This patch makes sure that we configure the correct size (minimum of local and remote values) and use it when determining whether to send new packets or not. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Remove unnecessary h5_build_pkt functionJohan Hedberg
The implementation of h5_build_packet can be moved into h5_prepare_pkt since all h5_prepare_pkt does is determine whether the packet is reliable and then call h5_build_packet. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Implement proper low-power support for Three-wire UARTJohan Hedberg
This patch adds on-demand wakeup request sending (and re-sendind) when we are in low-power state. When the controller enters this state it will send a sleep message after which the host is not allowed to send any other packets until a wakeup request has been sent and the woken message received as a response to it. The wakeup requests are re-sent periodically until a woken message is received. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add initialization tracking to HCI Three-wire driverJohan Hedberg
This patch adds tracking for the uninitialized, initialized and active states for Three-wire UART. This is needed so we can handle periodic sending of the Link Establishment messages before reaching active state and so that we do not try to do any higher level HCI data transmission before reaching active state. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add initial sleep support to Three-wire UARTJohan Hedberg
This patch adds very basic support for the sleep related messages. The only thing the code does right now is send a wakeup message as soon as receiving a sleep one, essentially preventing the controller from going to sleep. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Improve rx debug logs for Three-wire UARTJohan Hedberg
Remove unnecessary debug logs and add some to more centralized places. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Use delayed init for Three-wire UARTJohan Hedberg
This patch takes into use the delayed initialization feature that the Bluetooth UART framework provides. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add delayed init sequence support for UART controllersJohan Hedberg
This patch makes it possible to have UART drivers perform an internal initialization before calling hci_register_dev. This allows moving a lot of init code from user space (hciattach) to the kernel side, thereby creating a more controlled/robust initialization process. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Simplify hci_uart_tty_close logicJohan Hedberg
This patch cleans up and reduces indentation in the hci_uart_tty_close function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add support for Three-wire Link Control packetsJohan Hedberg
This patch adds basic support for parsing and sending Three-wire UART Link Control packets. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Fix/implement Three-wire reliable packet sendingJohan Hedberg
This patch should complete the necessary code for sending reliable Three-wire packets. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add Three-wire header value convenience macrosJohan Hedberg
This patch adds convenience macros for reading Three-wire header values. This will help make the code more readable. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add initial packet sending support to Three-wire UARTJohan Hedberg
This patch adds initial packed encoding and sending support to the Three-wire UART HCI transport driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add basic packet parsing to Three-wire UART driverJohan Hedberg
This patch adds basic packet parsing to the Three-wire UART HCI driver for packets received from the controller. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add initial reliable packet support for Three-wire UARTJohan Hedberg
This patch adds initial support for reliable packets along with the necessary retransmission timer for the Three-wire UART HCI driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Add basic state tracking to Three-wire UART driverJohan Hedberg
This patch adds basic state tracking and socket buffer handling to the Three-wire UART (H5) HCI driver. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-17Bluetooth: Initial skeleton for Three-wire UART (H5) supportJohan Hedberg
This patch adds the initial skeleton for Three-wire UART (H5) support and hooks it up to the HCI UART framework. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-09Bluetooth: btmrvl: trivial style fixesAndrei Emeltchenko
Patch shortens locals scope and adds missing braces. This is a diff between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do not send vendor events to bluetooth stack". Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-30Bluetooth: bluecard_cs: Shorten scope for iobaseAndrei Emeltchenko
Shortening scope shall silence some warnings reported by Geert Uytterhoeven: ... drivers/bluetooth/bluecard_cs.c: warning: unused variable 'iobase' [-Wunused-variable] ... Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-30Bluetooth: Fix warning: using int as NULL pointerAndrei Emeltchenko
Fix for warnings below: ... drivers/bluetooth/bt3c_cs.c:667:20: warning: Using plain integer as NULL pointer drivers/bluetooth/btuart_cs.c:596:20: warning: Using plain integer as NULL pointer ... Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-30Bluetooth: cleanup dtl1_configDevendra Naga
Improve the error handling of dtl1_config() Signed-off-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-26Merge branch 'for-upstream' of ↵Gustavo Padovan
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2012-06-19Bluetooth: btmrvl: Do not send vendor events to bluetooth stackAndrei Emeltchenko
Vendor-specific events shall be processed in driver and not sent to bluetooth stack where they screw up HCI command countings. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-11Bluetooth: add support for atheros 0930:0219Giancarlo Formicuccia
Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ. usb-devices shows: T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0219 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-09Bluetooth: Support AR3011 in Acer Iconia Tab W500Marek Vasut
Acer used this chip connected via USB: Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x3005 AR3011 Bluetooth bcdDevice 0.01 iManufacturer 0 iProduct 0 iSerial 0 bNumConfigurations 1 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-05Bluetooth: btmrvl: add SD8787 Bluetooth AMP device IDBing Zhao
SD8787 SDIO function 3 (device ID 0x911B) is for Bluetooth AMP. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-05Bluetooth: Remove unnecessary headers includeGustavo Padovan
Most of the include were unnecessary or already included by some other header. Replace module.h by export.h where possible. Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-06-05Bluetooth: Remove 'register' usage from the subsystemGustavo Padovan
Let the compiler chooses what is best. Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-06-05Bluetooth: Rename HCI_QUIRK_NO_RESET to HCI_QUIRK_RESET_ON_CLOSESzymon Janc
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to reset device on close instead of init, not to not reset at all. Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion. Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-05-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull more networking updates from David Miller: "Ok, everything from here on out will be bug fixes." 1) One final sync of wireless and bluetooth stuff from John Linville. These changes have all been in his tree for more than a week, and therefore have had the necessary -next exposure. John was just away on a trip and didn't have a change to send the pull request until a day or two ago. 2) Put back some defines in user exposed header file areas that were removed during the tokenring purge. From Stephen Hemminger and Paul Gortmaker. 3) A bug fix for UDP hash table allocation got lost in the pile due to one of those "you got it.. no I've got it.." situations. :-) From Tim Bird. 4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll try to coalesce overlapping frags and crash. Fix from Eric Dumazet. 5) RCU routing table lookups can race with free_fib_info(), causing crashes when we deref the device pointers in the route. Fix by releasing the net device in the RCU callback. From Yanmin Zhang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits) tcp: take care of overlaps in tcp_try_coalesce() ipv4: fix the rcu race between free_fib_info and ip_route_output_slow mm: add a low limit to alloc_large_system_hash ipx: restore token ring define to include/linux/ipx.h if: restore token ring ARP type to header xen: do not disable netfront in dom0 phy/micrel: Fix ID of KSZ9021 mISDN: Add X-Tensions USB ISDN TA XC-525 gianfar:don't add FCB length to hard_header_len Bluetooth: Report proper error number in disconnection Bluetooth: Create flags for bt_sk() Bluetooth: report the right security level in getsockopt Bluetooth: Lock the L2CAP channel when sending Bluetooth: Restore locking semantics when looking up L2CAP channels Bluetooth: Fix a redundant and problematic incoming MTU check Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C Bluetooth: Fix EIR data generation for mgmt_device_found Bluetooth: Fix Inquiry with RSSI event mask Bluetooth: improve readability of l2cap_seq_list code Bluetooth: Fix skb length calculation ...
2012-05-18USB: Disable hub-initiated LPM for comms devices.Sarah Sharp
Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-16Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03CMichael Gruetzner
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to the blacklist of btusb module and add it to the ath3k module to properly load the firmware in Kernel 3.3.4 The device is integrated in e.g. some Acer Aspire 7750G. Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e03c Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Michael Gruetzner <mgruetzn@gmx.de> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btmrvl: add support for SDIO suspend/resume callbacksAmitkumar Karwar
Host sleep is activated using already configured host sleep parameters in suspend handler and it is cancelled in resume handler. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btmrvl: configure default host sleep parametersAmitkumar Karwar
Currently debugfs commands "hscfgcmd" and "gpiogap" are provided for host sleep configuration. But if user doesn't configure host sleep parameters using these commands, host sleep activation is failed during suspend (support for suspend and resume handlers is added in next patch). Default host sleep configuration is done during driver initialisation in this patch. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btusb: Dynamic alternate settingMikel Astiz
The alternate setting must be dynamically set according to the number of active SCO links, and the bit depth of the audio. The possible values for the alternate setting are described in the Bluetooth Core Specification, Volume 4, Part B, section 2.1.1. Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: btmrvl_sdio: remove pointless conditional before release_firmware()Jesper Juhl
release_firmware() deals gracefullt with NULL pointers so there's no reason to test for one prior to calling the function. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09Bluetooth: vhci: Ignore return code of nonseekable_open()David Herrmann
The comment in ./fs/open.c clearly states that nonseekable_open() will never fail. Therefore, we can safely ignore the return code. This is the recommended way to deal with nonseekable_open(). Our current code looks like nonseekable_open() is checked for the return code. However, if we check the return code, we must also kfree() our private data if the open fails. To avoid this overhead and to avoid confusion, we simply drop the return code and return 0. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-05-09Bluetooth: Remove redundant hdev->parent fieldDavid Herrmann
We initialize the "struct device" in hci_alloc_dev() for a long time now so we can access hdev->dev.parent directly. Hence, we can drop the temporary field hdev->parent which is used in no other place than hci_add_sysfs(). SET_HCIDEV_DEV() is never called after registering a device by the drivers so we do not overwrite internal device-state. Furthermore, hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the default behavior with dev.parent = NULL is kept. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-04-27Merge branch 'for-upstream' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2012-04-24Add Foxconn / Hon Hai IDs for btusb moduleSteven Harms
This change adds 0x0489:0xe033 to the btusb module. This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook. Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e033 Rev= 2.29 S: Manufacturer=Broadcom Corp S: Product=Acer Module S: SerialNumber=60D819F74101 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Steven Harms <sjharms@gmail.com> Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-04-19Bluetooth: Add support for AR3012 [0cf3:e004]AceLan Kao
Add another vendor specific ID for Atheros AR3012 output of usb-devices: T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e004 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/922715 Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-04-13Bluetooth: Add support for Atheros [13d3:3362]AceLan Kao
Add another vendor specific ID for Atheros AR3012 device. This chip is wrapped by IMC Networks. output of usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3362 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-04-13Bluetooth: btusb: Add vendor specific ID (0489 e042) for BCM20702A0Manoj Iyer
T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e042 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DCA61B5 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Reported-by: Dennis Chua <dennis.chua@canonical.com> Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-04-09Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
2012-04-05Merge branch 'akpm' (Andrew's patch-bomb)Linus Torvalds
Merge batch of fixes from Andrew Morton: "The simple_open() cleanup was held back while I wanted for laggards to merge things. I still need to send a few checkpoint/restore patches. I've been wobbly about merging them because I'm wobbly about the overall prospects for success of the project. But after speaking with Pavel at the LSF conference, it sounds like they're further toward completion than I feared - apparently davem is at the "has stopped complaining" stage regarding the net changes. So I need to go back and re-review those patchs and their (lengthy) discussion." * emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches) memcg swap: use mem_cgroup_uncharge_swap fix backlight: add driver for DA9052/53 PMIC v1 C6X: use set_current_blocked() and block_sigmask() MAINTAINERS: add entry for sparse checker MAINTAINERS: fix REMOTEPROC F: typo alpha: use set_current_blocked() and block_sigmask() simple_open: automatically convert to simple_open() scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open() libfs: add simple_open() hugetlbfs: remove unregister_filesystem() when initializing module drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback fs/xattr.c:setxattr(): improve handling of allocation failures fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed fs/xattr.c: suppress page allocation failure warnings from sys_listxattr() sysrq: use SEND_SIG_FORCED instead of force_sig() proc: fix mount -t proc -o AAA
2012-04-05simple_open: automatically convert to simple_open()Stephen Boyd
Many users of debugfs copy the implementation of default_open() when they want to support a custom read/write function op. This leads to a proliferation of the default_open() implementation across the entire tree. Now that the common implementation has been consolidated into libfs we can replace all the users of this function with simple_open(). This replacement was done with the following semantic patch: <smpl> @ open @ identifier open_f != simple_open; identifier i, f; @@ -int open_f(struct inode *i, struct file *f) -{ ( -if (i->i_private) -f->private_data = i->i_private; | -f->private_data = i->i_private; ) -return 0; -} @ has_open depends on open @ identifier fops; identifier open.open_f; @@ struct file_operations fops = { ... -.open = open_f, +.open = simple_open, ... }; </smpl> [akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-29Bluetooth: btusb: typo in Broadcom SoftSailing idDon Zickus
I was trying to backport the following commit to RHEL-6 From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001 From: Oliver Neukum <oliver@neukum.org> Date: Wed, 21 Sep 2011 11:37:15 +0200 Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing and noticed it wasn't working on an HP Elitebook. Looking into the patch I noticed a very subtle typo in the ids. The patch has '0x05ac' instead of '0x0a5c'. A snippet of the lsusb -v output also shows this: Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 1 bDeviceProtocol 1 bMaxPacketSize0 64 idVendor 0x0a5c Broadcom Corp. idProduct 0x21e1 bcdDevice 1.12 iManufacturer 1 Broadcom Corp iProduct 2 BCM20702A0 iSerial 3 60D819F0338C bNumConfigurations 1 Looking at other Broadcom ids, the fix matches them whereas the original patch matches Apple's ids. Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads correctly. Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-17 08:43:53 +0000