| Age | Commit message (Collapse) | Author |
|---|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
|
|
The of_clk_set_defaults() function is used in subsystems which can
be built as module. Add the missing symbol export entry so there
is no build errors like:
"ERROR: "of_clk_set_defaults" [drivers/i2c/i2c-core.ko] undefined!".
Fixes commit: 86be408bfbd846fab3c4ac21d6f9298bd2e4b790
"clk: Support for clock parents and rates assigned from device tree"
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
There is a cut and paste bug so we check "pclk" instead of "clk".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-next-samsung
Samsung clock patches for 3.17
1) non-critical fixes (without need to push to stable):
d5e136a clk: samsung: Register clk provider only after registering its all clocks
305cfab clk: samsung: Make of_device_id array const
e9d5295 clk: samsung: exynos5420: Setup clocks before system suspend
f65d518 clk: samsung: trivial: Correct typo in author's name
2) Exynos CLKOUT driver:
800c979 clk: samsung: exynos4: Add missing CPU/DMC clock hierarchy
01f7ec2 clk: samsung: exynos4: Add CLKOUT clock hierarchy
1e832e5 clk: samsung: Add driver to control CLKOUT line on Exynos SoCs
d19bb39 ARM: dts: exynos: Update PMU node with CLKOUT related data
3) Clock hierarchy extensions:
17d3f1d clk: exynos4: Add PPMU IP block source clocks.
ca5b402 clk: samsung: register exynos5420 apll/kpll configuration data
4) ARM CLKDOWN functionality enablement for Exynos4 and 3250:
42773b2 clk: samsung: exynos4: Enable ARMCLK down feature
45c5b0a clk: samsung: exynos3250: Enable ARMCLK down feature
|
|
ABE DPLL frequency need to be lowered from 361267200
to 180633600 to facilitate the ATL requironments.
The dpll_abe_m2x2_ck clock need to be set to double
of ABE DPLL rate in order to have correct clocks
for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
If the .debug_init op is provided, it will be called by
clk_debug_create_one(). If debug_init() returns an error code,
clk_debug_create_one() will return -ENOMEM, regardless of the
value returned from debug_init(). Tweak the code to return
the actual value returned by debug_init() instead.
Signed-off-by: Chris Brand <chris.brand@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This adds the clock driver for Cirrus Logic CLPS711X series SoCs
using common clock infrastructure.
Designed primarily for migration CLPS711X subarch for multiplatform & DT,
for this as the "OF" and "non-OF" calls implemented.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch uses CLK_DIVIDER_ROUND_CLOSEST flag to specify
the divider has to round to closest div.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch extend the range of possible frequencies of the fs432c65
and fs660c32 Quad frequency synthesizers.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch added support for DT registration of ClockGenA9
It includes c32 type PLL.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch added support for ClockGenD0/D2/D3
It includes one 660 Quadfs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch added support for DT registration of ClockGenC0
It includes 2 c32 type PLL and a 660 Quadfs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch adds the support of quadfs reset handling.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch introduces polarity indication for pll power up bit
and for standby bit in order to have same code between stih416
and stih407 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch added support for DT registration of ClockGenA0
It includes c32 type PLL.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The patch supports the A9-mux clocks used by ClockGenA9
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This patch is the Flexgen implementation reusing as much as possible
of Common Clock Framework functions.
The idea is to have an instance of "struct flexgen" per output clock.
It represents the clock cross bar (by a mux element), and the pre and final dividers
(using dividers and gates elements).
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
converts clkgen_pll_data tables into static const
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
converts stm_fs tables into static const
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
There are some structs and arrays on the driver that are not used
anywhere else. Let's mark them as static.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This commit adds __iomem thoughout the sunxi clock driver, in places
where it was ommited. This cleans most of the sparse warnings we
are getting here.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Register the PLL configuration data for APLL and KPLL on Exynos5420. This
configuration data table specifies PLL coefficients for supported PLL
clock speeds when a 24MHz clock is supplied as the input clock source
for these PLLs.
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Arjun K.V <arjun.kv@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Prior to suspending the system, we need to ensure that certain
clock source and gate registers are unmasked.
while at it, add these clks to save/restore list also.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Array of struct of_device_id may be be const as expected by
of_match_table field and of_find_matching_node_and_match() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Enable ARMCLK down feature on Exynos3250 SoC. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor.
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
Enable ARMCLK down feature on all Exynos4 SoCs. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor. In idle
mode this reduces energy consumption on full frequency chosen by
cpufreq governor by approximately:
- Trats2: 6.5% (153 mA -> 143 mA)
- Trats: 33.0% (180 mA -> 120 mA)
- Gear1: 27.0% (180 mA -> 130 mA)
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature and on Exynos4412 ARMCLK down is
enabled for all 4 cores.
Tested on Trats board (Exynos4210), Trats2 board (Exynos4412) and
Samsung Gear 1 (Exynos4212).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
This patch introduces a driver that handles configuration of CLKOUT pin
of Exynos SoCs that can be used to output certain clocks from inside of
the SoC to a dedicated output pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
This patch adds definitions of clocks that are used to drive clock
output signals of particular CMU sub-blocks that are then fed to PMU and
handled by Exynos CLKOUT driver added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next-sunxi
Allwinner clocks additions for 3.17
This pull request adds support for the clocks found in the newly supported
Allwinner A23 clocks.
|
|
This patch adds missing definitions of clocks from CPU and DMC clock
domains, which are necessary to properly represent CLKOUT clock hierarchy
added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into clk-next-msm
qcom clock changes for 3.17
These patches add support for a handful of Qualcomm's SoC clock
controllers: APQ8084 gcc and mmcc, IPQ8064 gcc, and APQ8064.
There's also a small collection of bug fixes that aren't critical
-rc worthy regressions because the consumer drivers aren't present
or using the buggy clocks and one optimization for HDMI.
|
|
clk-next-ti
|
|
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
The APQ8064 multimedia clock controller is fairly similar to the
8960 multimedia clock controller, except that gfx2d0/1 has been
removed and the gfx3d frequency is slightly faster when using the
newly introduced PLL15. We also add vcap clocks and a couple new
TV clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Some SR type PLLs need to be configured for a certain rate when
linux boots. Add support for these types of PLLs so that we can
program PLL15's rate on apq8064.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The mdp_lut_clk isn't a child of the mdp_clk. Instead it's the
child of the mdp_src clock. Fix it.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Sometimes we need to program PLLs with a fixed rate
configuration during driver probe. Doing this after we register
the PLLs with the clock framework causes the common clock
framework to assume the rate of the PLLs are 0. This causes all
sorts of problems for rate recalculations because the common
clock framework caches the rate once at registration time unless
a flag is set to always recalculate the rates.
Split the qcom_cc_probe() function into two pieces, map and
everything else, so that drivers which need to configure some
PLL rates or otherwise twiddle bits in the clock controller can
do so before registering clocks. This allows us to properly
detect the rates of PLLs that are programmed at boot.
Fixes: 49fc825f0cc2 "clk: qcom: Consolidate common probe code"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Clocks that don't have a pre-divider don't list any pre-divider
in their frequency tables, but their tables are initialized using
aggregate initializers. Use tagged initializers so we properly
assign the m and n values for each frequency. Furthermore, the
mmcc_pxo_pll8_pll2_pll3 array improperly mapped the second
element to pll2 instead of pll8, causing the clock driver to
recalculate the wrong rate for any clocks using this array along
with a rate that uses pll2. Plus the .num_parents field is 3
instead of 4 so you can't even switch the parent to pll3. Finally
I noticed that the jpegd clock improperly indicates that the
pre-divider width is only 2, when it's actually 4 bits wide.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
In the case of HDMI clocks, we want to bypass the RCG's ability
to divide the output clock and pass through the parent HDMI PLL
rate. Add a simple set of clk_ops to configure the RCG to do
this. This removes the need to keep adding more frequency entries
to the tv_src clock whenever we want to support a new rate.
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add a driver for the global clock controller found on IPQ8064 based
platforms. This should allow most non-multimedia device drivers to probe
and control their clocks.
This is currently missing clocks for USB HSIC and networking devices.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the multimedia clock controller found on the APQ8084
based platforms. This will allow the multimedia device drivers to
control their clocks.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
[sboyd: Rework parent mapping to avoid conflicts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
sun6i-apb0-gates uses the "clock-indices" DT property to indicate
valid gate bits or holes in between. However, the rest of sunxi
clock drivers use bitmaps for this purpose.
This patch modifies sun6i-apb0-gates to use bitmaps as well, to be
consistent with the sunxi platform. Also add the missing call to
clk_register_clkdev, so system clock lookups will work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
|
|
Add the clock tree definition for the new rk3288 SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This adds a clock driver that handles the specific muxes, dividers and gates
of rk3188 and rk3066 SoCs.
The structure of the clock list resembles the arrangement of their
counterparts in the clock architecture diagrams found in the SoC
documentation.
Clocks exported to the clock provider are currently limited to well known
or measured ones. So additional clock exports may be necessary in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
All Rockchip SoCs at least down to the ARM9-based RK28xx include the reset-
controller for SoC peripherals in their clock controller.
While the older SoCs (ARM9 and Cortex-A8) use a regular scheme to change
register values, the Cortex-A9 SoCs use a hiword-mask making locking unecessary.
To be compatible with both schemes the reset controller takes a flag to
decide which scheme to use, similar to the other HIWORD_MASK flags used in the
clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
All known Rockchip SoCs down to the RK28xx (ARM9) use a similar pattern to
handle their plls:
|--\
xin32k ----------------|mux\
xin24m -----| pll |----|pll|--- pll output
\---------------|src/
|--/
The pll output is sourced from 1 of 3 sources, the actual pll being one of
them. To change the pll frequency it is imperative to remux it to another
source beforehand. This is done by adding a clock-listener to the pll that
handles the remuxing before and after the rate change.
The output mux is implemented as a separate clock to make use of already
existing common-clock features for disabling the pll if one of the other
two sources is used.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
