| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
|
|
The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a P-state driver for the Intel Sandy bridge processor. In cpufreq
terminology this driver implements a scaling driver with an internal
governor.
When built into the the kernel this driver will be the preferred
scaling driver for Sandy bridge processors.
In addition to the interfaces provided by the cpufreq subsystem for
controlling scaling drivers. The user may control the behavior of the
driver via three sysfs files located in
"/sys/devices/system/cpu/intel_pstate".
max_perf_pct: limits the maximum P state that will be requested by
the driver stated as a percentage of the avail performance.
min_perf_pct: limits the minimum P state that will be requested by
the driver stated as a percentage of the avail performance.
no_turbo: limits the driver to selecting P states below the turbo
frequency range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add an imx6q-cpufreq driver for Freescale i.MX6Q SoC to handle the
hardware specific frequency and voltage scaling requirements.
The driver supports module build and is instantiated by the platform
device/driver mechanism, so that it will not be instantiated on other
platforms, as IMX is built with multiplatform support.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that the majority of x86 CPUs out there are supported by
acpi-cpufreq, we want it to load first and, in the AMD case, drop to
powernow-k8 only on K8s. If, however, both powernow-k8 and acpi-cpufreq
are built-in, the link order matters. Correct that.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* depends/cleanup: (375 commits)
ARM: at91: fix board-rm9200-dt after sys_timer conversion
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
timer: vt8500: Move timer code to drivers/clocksource
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
...
|
|
This driver doesn't only handle cpufreq functionality for the
db8500 anymore. There are new variants which rely on it too.
Let's make the name a bit more generic.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 2aacdff entitled "cpufreq: Move common part from governors
to separate file", whenever the drivers that depend on this new file
(cpufreq_ondemand or cpufreq_conservative) are built as modules, a new
module named cpufreq_governor is created because the Makefile includes
cpufreq_governor.o twice. As drivers/cpufreq/cpufreq_governor.c contains no
MODULE directives, the resulting module has no license specified, which
results in logging of a "module license 'unspecified' taints kernel". In
addition, a number of globals are exported GPL only, and are therefore
not available. This fix establishes a new boolean configuration variable
that forces cpufreq_governor.o to be linked into the kernel whenever
either cpufreq_ondemand or cpufreq_conservative is selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Multiple cpufreq governers have defined similar get_cpu_idle_time_***()
routines. These routines must be moved to some common place, so that all
governors can use them.
So moving them to cpufreq_governor.c, which seems to be a better place for
keeping these routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support. It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
These chips are now supported by acpi-cpufreq, so we can delete all the
code handling them.
Andre: Tighten the deprecation warning message. Trigger load of
acpi-cpufreq and let the load of the module finally fail.
This avoids the problem of users ending up without any cpufreq support
after the transition.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
Pull cpufreq updates for 3.4 from Dave Jones: new drivers and some fixes.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
provide disable_cpufreq() function to disable the API.
EXYNOS5250: Add support cpufreq for EXYNOS5250
EXYNOS4X12: Add support cpufreq for EXYNOS4X12
[CPUFREQ] CPUfreq ondemand: update sampling rate without waiting for next sampling
[CPUFREQ] Add S3C2416/S3C2450 cpufreq driver
[CPUFREQ] Fix exposure of ARM_EXYNOS4210_CPUFREQ
[CPUFREQ] EXYNOS4210: update the name of EXYNOS clock register
[CPUFREQ] EXYNOS: Initialize locking_frequency with initial frequency
[CPUFREQ] s3c64xx: Fix mis-cherry pick of VDDINT
Fix up trivial conflicts in Kconfig and Makefile due to just changes
next to each other (OMAP2PLUS changes vs some new EXYNOS cpufreq
drivers).
|
|
This patch adds support cpufreq for EXYNOS5250 SoC. Basically,
the exynos-cpufreq.c is used commonly and exynos5250-cpufreq.c
is used for EXYNOS5250(two Cortex-A15 cores) SoC.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch adds support cpufreq for EXYNOS4X12 SoCs. Basically,
the exynos-cpufreq.c is used commonly and exynos4x12-cpufreq.c
is used for EXYNOS4212(two Cortex-A9 cores) and EXYNOS4412(four
Cortex-A9 cores) SoCs.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
The S3C2416/S3C2450 SoCs support two sources for the armclk.
The first source is the so called armdiv which divides the msysclk down
to provide necessary cpu rates. In this mode the core voltage must be
always at 1.3V. The frequency from the armdiv is not allowed to be
lower than the hclk frequency.
In the second mode the armclk can be sourced directly from the hclk in
the so called "dynamic voltags scaling" (dvs) mode. Here the armdiv
isn't used at all. Also in this mode the core voltage may be lowered.
Existing hardware and tests with it suggest 1.0V as sufficient.
When changing the clock source to the armdiv from the hclk, the SoC
shows stability issues if the new frequency is higher than the current
hclk frequency. Hence the driver always forces the armdiv to the hclk
frequency before the source change and lets the cpufreq issue another
set_target call for higher frequencies.
To mark the hclk frequency as lower as the corresponding armdiv
frequency it is set 1MHz below the real frequency. This lets the cpufreq
framework change between 133MHz based on hclk and 133MHz based on armdiv
at will.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Andrey Gusakov <dron0gus@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
The OMAP driver depends on CPUfreq table support for creating a table
of frequencies from the OPP layer. Ensure that it's build to avoid
link-time errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[khilman@ti.com: make user-selectable, but default y]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
To support various EXYNOS series SoCs commonly,
added exynos common structure.
exynos-cpufreq.c => EXYNOS series common cpufreq driver
exynos4210-cpufreq.c => EXYNOS4210 support cpufreq driver
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Move OMAP cpufreq driver from arch/arm/mach-omap2 into
drivers/cpufreq, along with a few cleanups:
- generalize support for better handling of different SoCs in the OMAP
- use OPP layer instead of OMAP clock internals for frequency table init
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: move to drivers]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
|
|
Add simple cpufreq driver for Maple-based boards (ppc970fx evaluation
kit and others). Driver is based on a cpufreq driver for 64-bit powermac
boxes with all pmac-dependant features removed and simple cleanup
applied.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
|
|
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This is a straight code motion patch, there are no changes to the driver
itself. The Kconfig is left untouched as the ARM CPUfreq Kconfig is all
in one big block in arm/Kconfig and should be moved en masse rather than
being done piecemeal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Concluding interface update and movement of the driver by making
the DB8500 cpufreq driver compile in the cpufreq subsystem.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
A new cpufreq module, based on the ondemand one with my additional patches
just posted. This one is more suitable for battery environments where its
probably more appealing to have the cpu freq gracefully increase and decrease
rather than flip between the min and max freq's.
N.B. Bruno Ducrot pointed out that the amd64's "do have unacceptable latency
between min and max freq transition, due to the step-by-step requirements
(200MHz IIRC)"; so AMD64 users would probably benefit from this too.
Signed-off-by: Alexander Clouter <alex-kernel@digriz.org.uk>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
