| Age | Commit message (Collapse) | Author |
|---|
|
Currently, Mode-Control register is accessed by read-modify-write.
According to DMA hardware specifications datasheet, prohibits this method.
Because this register resets to 0 by DMA HW after DMA transfer completes.
Thus, current read-modify-write processing can cause unexpected behavior.
The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'.
e.g. Set DMA0=01b DMA11=10b
CTL0=33333331h
CTL2=00002333h
NOTE:
CTL0 includes DMA0~7 Mode-Control register.
CTL2 includes DMA8~11 Mode-Control register.
This patch modifies the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix for the following INFO message
=================================
[ INFO: inconsistent lock state ]
2.6.39+ #89
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
rs232/822 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&pd_chan->lock)->rlock){?.....}, at: [<c123b9a1>] pdc_desc_get+0x16/0xab
{HARDIRQ-ON-W} state was registered at:
[<c104fe28>] mark_irqflags+0xbd/0x11a
[<c1050386>] __lock_acquire+0x501/0x6bb
[<c1050945>] lock_acquire+0x63/0x7b
[<c131c51d>] _raw_spin_lock_bh+0x43/0x51
[<c123bee4>] pd_alloc_chan_resources+0x92/0x11e
[<c123ad62>] dma_chan_get+0x9b/0x107
[<c123b2d1>] __dma_request_channel+0x61/0xdc
[<c11ba24b>] pch_request_dma+0x61/0x19e
[<c11bb3b8>] pch_uart_startup+0x16a/0x1a2
[<c11b8446>] uart_startup+0x87/0x147
[<c11b9183>] uart_open+0x117/0x13e
[<c11a5c7d>] tty_open+0x23c/0x34c
[<c1097705>] chrdev_open+0x140/0x15f
[<c10930a6>] __dentry_open.clone.14+0x14a/0x22b
[<c1093dfb>] nameidata_to_filp+0x36/0x40
[<c109f28b>] do_last+0x513/0x635
[<c109f4af>] path_openat+0x9c/0x2aa
[<c109f6e4>] do_filp_open+0x27/0x69
[<c1093f02>] do_sys_open+0xfd/0x184
[<c1093fad>] sys_open+0x24/0x2a
[<c131d58c>] sysenter_do_call+0x12/0x32
irq event stamp: 2522
hardirqs last enabled at (2521): [<c131ca3b>] _raw_spin_unlock_irqrestore+0x36/0x52
hardirqs last disabled at (2522): [<c131db27>] common_interrupt+0x27/0x34
softirqs last enabled at (2354): [<c102fa11>] __do_softirq+0x10a/0x11a
softirqs last disabled at (2299): [<c10041a4>] do_softirq+0x57/0xa4
other info that might help us debug this:
2 locks held by rs232/822:
#0: (&tty->atomic_write_lock){+.+.+.}, at: [<c11a4b7a>] tty_write_lock+0x14/0x3c
#1: (&port_lock_key){-.....}, at: [<c11bad72>] pch_uart_interrupt+0x17/0x1e9
stack backtrace:
Pid: 822, comm: rs232 Not tainted 2.6.39+ #89
Call Trace:
[<c1319f90>] ? printk+0x19/0x1b
[<c104f893>] print_usage_bug+0x184/0x18f
[<c104e5b1>] ? print_irq_inversion_bug+0x10e/0x10e
[<c104f943>] mark_lock_irq+0xa5/0x1f6
[<c104fc9c>] mark_lock+0x208/0x2d7
[<c104fdc0>] mark_irqflags+0x55/0x11a
[<c1050386>] __lock_acquire+0x501/0x6bb
[<c10042ee>] ? dump_trace+0x92/0xb6
[<c1050945>] lock_acquire+0x63/0x7b
[<c123b9a1>] ? pdc_desc_get+0x16/0xab
[<c131c2d0>] _raw_spin_lock+0x3e/0x4c
[<c123b9a1>] ? pdc_desc_get+0x16/0xab
[<c123b9a1>] pdc_desc_get+0x16/0xab
[<c10504d8>] ? __lock_acquire+0x653/0x6bb
[<c123bb2c>] pd_prep_slave_sg+0x7c/0x1cb
[<c1006c3f>] ? nommu_map_sg+0x6e/0x81
[<c11bace6>] dma_handle_tx+0x2cf/0x344
[<c11bad72>] ? pch_uart_interrupt+0x17/0x1e9
[<c11baebb>] pch_uart_interrupt+0x160/0x1e9
[<c10642fb>] handle_irq_event_percpu+0x25/0x127
[<c1064429>] handle_irq_event+0x2c/0x43
[<c1065e0d>] ? handle_fasteoi_irq+0x84/0x84
[<c1065eb9>] handle_edge_irq+0xac/0xce
<IRQ> [<c1003ecb>] ? do_IRQ+0x38/0x9d
[<c131db2e>] ? common_interrupt+0x2e/0x34
[<c105007b>] ? __lock_acquire+0x1f6/0x6bb
[<c131ca3d>] ? _raw_spin_unlock_irqrestore+0x38/0x52
[<c11b798b>] ? uart_start+0x2d/0x32
[<c11b7998>] ? uart_flush_chars+0x8/0xa
[<c11a7962>] ? n_tty_write+0x12c/0x1c6
[<c1027a73>] ? try_to_wake_up+0x251/0x251
[<c11a4d0b>] ? tty_write+0x169/0x1dc
[<c11a7836>] ? n_tty_ioctl+0xb7/0xb7
[<c1094841>] ? vfs_write+0x91/0x10d
[<c11a4ba2>] ? tty_write_lock+0x3c/0x3c
[<c1094a69>] ? sys_write+0x3e/0x63
[<c131d58c>] ? sysenter_do_call+0x12/0x32
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Tested-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
ISSUE: In case PCH_DMA with I2S communications with ch8~ch11, sometimes I2S data
is not send correctly.
CAUSE: The following patch I submitted before was not enough modification for
supporting DMA ch8~ch11. The modification for status register of ch8~11 was not
enough.
pch_dma: Support I2S for ML7213 IOH
author Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Mon, 9 May 2011 07:09:38 +0000 (16:09 +0900)
committer Vinod Koul <vinod.koul@intel.com>
Mon, 9 May 2011 11:42:23 +0000 (16:42 +0530)
commit 194f5f2706c7472f9c6bb2d17fa788993606581f
tree c9d4903ea02b18939a4f390956a48be1a3734517
parent 60092d0bde4c8741198da4a69b693d3709385bf1
This patch fixes the issue.
We can confirm PCH_DMA with I2S communications with ch8~ch11 works well.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Support I2S device for ML7213 IOH
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently, Direct-Start mode(*) is enabled.
Our IOH's devices must not use this mode.
This causes unexpected behavior.
This patch deletes Direct-Start setting.
(*) This mode is used in order for CPU to generate the DMA request.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix checkpatch warnings.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently, even-channel number is set as tx direction and odd is set as rx.
However, though video-in uses ch6, the direction is not tx but rx.
This patch sets video-in's DMA direction correctly.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In the function pdc_desc_get(), var 'i' is not
initialized before use. This patch fixes it.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When CONFIG_PM=n, we get the following warning:
drivers/dma/pch_dma.c:741: warning: ‘pch_dma_suspend’ defined but not used
drivers/dma/pch_dma.c:755: warning: ‘pch_dma_resume’ defined but not used
To fix it, wrap pch_dma_{suspend,resume} and
pch_dma_{save,restore}_regs functions with CONFIG_PM.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
set the number of array correctly.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
fix the following kernel error
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 _local_bh_enable_ip.clone.5+0x35/0x71()
Hardware name: To be filled by O.E.M.
Modules linked in: pch_uart pch_dma fuse mga drm cpufreq_ondemand acpi_cpufreq mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 uinput snd_hda_codec_realtek snd_hda_intel snd_hda_codec matroxfb_base snd_hwdep 8250_pnp snd_seq snd_seq_device matroxfb_DAC1064 snd_pcm joydev 8250 matroxfb_accel snd_timer matroxfb_Ti3026 ppdev pegasus parport_pc snd parport matroxfb_g450 g450_pll serial_core video output matroxfb_misc soundcore snd_page_alloc serio_raw pcspkr ext4 jbd2 crc16 sdhci_pci sdhci mmc_core floppy [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Not tainted 2.6.37.upstream_check+ #8
Call Trace:
[<c0433add>] warn_slowpath_common+0x65/0x7a
[<c043825b>] ? _local_bh_enable_ip.clone.5+0x35/0x71
[<c0433b01>] warn_slowpath_null+0xf/0x13
[<c043825b>] _local_bh_enable_ip.clone.5+0x35/0x71
[<c043829f>] local_bh_enable_ip+0x8/0xa
[<c06ec471>] _raw_spin_unlock_bh+0x10/0x12
[<f82b57dd>] pd_prep_slave_sg+0xba/0x200 [pch_dma]
[<f82f7b7a>] pch_uart_interrupt+0x44d/0x6aa [pch_uart]
[<c046fa97>] handle_IRQ_event+0x1d/0x9e
[<c047146f>] handle_fasteoi_irq+0x90/0xc7
[<c04713df>] ? handle_fasteoi_irq+0x0/0xc7
<IRQ> [<c04045af>] ? do_IRQ+0x3e/0x89
[<c04035a9>] ? common_interrupt+0x29/0x30
[<c04400d8>] ? sys_getpriority+0x12d/0x1a2
[<c058bb2b>] ? arch_local_irq_enable+0x5/0xb
[<c058c740>] ? acpi_idle_enter_bm+0x22a/0x261
[<c0648b11>] ? cpuidle_idle_call+0x70/0xa1
[<c0401f44>] ? cpu_idle+0x49/0x6a
[<c06d9fc4>] ? rest_init+0x58/0x5a
[<c089e762>] ? start_kernel+0x2d0/0x2d5
[<c089e0ce>] ? i386_start_kernel+0xce/0xd5
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently, in case of using scatter/gather mode, head of data is not sent to
destination. The cause is second descriptor address is set to NEXT.
The NEXT must have head of descriptor address.
This patch sets head of descriptor address to the NEXT.
Acked-by: Yong Wang <youg.y.wang@intel.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
[dan.j.williams@intel.com: fixed up usage of virt_to_phys()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
NULL-terminating pci_device_id in pch_dma.c and scx200_acb.c
for appying MODULE_DEVICE_TABLE (to publish modalias-es).
Signed-off-by: Dzianis Kahanovich <mahatma@eu.by>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Use {read|write}l instead of __raw_{read|write}l since PCH DMA
controller is PCI device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
