summaryrefslogtreecommitdiffstats
path: root/drivers/dma
AgeCommit message (Collapse)Author
2012-04-26Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
Pull [GIT PULL] slave-dmaengine fixes from Vinod Koul. * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine/amba-pl08x : reset phychan_hold on terminate all dma: pl330: fix a couple of compilation warnings dma/ste_dma40: fix erroneous comparison dma/ste_dma40: explicitly include regulator consumer header dma40: Improve the logic of stopping logical chan dmaengine: at_hdmac: remove clear-on-read in atc_dostart() dma: mxs-dma: enable channel in device_issue_pending call dmaengine: imx-dma: dont complete descriptor for cyclic dma
2012-04-25dmaengine/amba-pl08x : reset phychan_hold on terminate allDavide Ciminaghi
When a client calls pl08x_control with DMA_TERMINATE_ALL, it is correct to terminate and release the phy channel currently in use (if one is in use), but the phychan_hold counter must also be reset (otherwise it could get trapped in an unbalanced state). Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com> Reviewed-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-25dma: pl330: fix a couple of compilation warningsOlof Johansson
Move a couple of tests and do a minor refactor to avoid: drivers/dma/pl330.c: In function 'pl330_probe': drivers/dma/pl330.c:2929:215: warning: comparison of distinct pointer types lacks a cast [enabled by default] drivers/dma/pl330.c: In function 'pl330_tasklet': drivers/dma/pl330.c:2250:8: warning: 'pch' may be used uninitialized in this function [-Wuninitialized] drivers/dma/pl330.c:2228:25: note: 'pch' was declared here drivers/dma/pl330.c:2277:130: warning: 'pch' may be used uninitialized in this function [-Wuninitialized] drivers/dma/pl330.c:2260:25: note: 'pch' was declared here Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-23dma/ste_dma40: fix erroneous comparisonLinus Walleij
A small fallout from Vinod's conversions to dma_transfer_direction, this small comparison was done with a dma_data_direction instead. Fix it by comparing against the correct enum. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-23dma/ste_dma40: explicitly include regulator consumer headerLinus Walleij
The patch "ARM: amba: Remove AMBA level regulator support" breaks the DMA40 driver since the <linux/amba/bus.h> header implicitly included the regulator consumer header. So include it explicitly and fix the build error. Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-23dma40: Improve the logic of stopping logical chanNarayanan G
can be directly stopped by issuing a SUSPEND_REQ on the EE bits. There is no need to suspend the physical channel and restart it. Also, the support for pre-V2 hw is discontinued. EE bits for writing: 00: disable only if AS=11 or AS=00 01: enable 10: suspend_req only if AS=01 & EE=01 or EE=11 11: round / no change for writing Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-20dmaengine: at_hdmac: remove clear-on-read in atc_dostart()Nicolas Ferre
This loop on EBCISR register was designed to clear IRQ sources before enabling a DMA channel. This register is clear-on-read so a race condition can appear if another channel is already active and has just finished its transfer. Removing this read on EBCISR is fixing the issue as there is no case where an IRQ could be pending: we already make sure that this register is drained at probe() time and during resume. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-20dma: mxs-dma: enable channel in device_issue_pending callShawn Guo
Enable channel in device_issue_pending call, so that the order between cookie assignment and channel enabling can be ensured naturally. It fixes the mxs gpmi-nand breakage which is caused by the incorrect order of cookie assigning and channel enabling. Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Huang Shijie <b32955@freescale.com> Tested-by <samgandhi9@gmail.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-20dmaengine: imx-dma: dont complete descriptor for cyclic dmaVinod Koul
the cookie updates completed the cyclic dma descriptor wrongly. This caused the BUG_ON to be hit as submit is called for completed descriptor Fix this by not marking the cyclic descriptor as complete Tested-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-17dmaengine: Kconfig: fix Atmel at_hdmac entryNicolas Ferre
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will allow to select this driver for newer chips. Keep dependency on AT91 because of the use of an header file located in include/mach directory. Modify the comment to reflect this. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-04-10Merge tag 'dmaengine-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine Pull dmaengine fixes from Dan Williams: 1/ regression fix for Xen as it now trips over a broken assumption about the dma address size on 32-bit builds 2/ new quirk for netdma to ignore dma channels that cannot meet netdma alignment requirements 3/ fixes for two long standing issues in ioatdma (ring size overflow) and iop-adma (potential stack corruption) * tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine: netdma: adding alignment check for NETDMA ops ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata ioat: ring size variables need to be 32bit to avoid overflow iop-adma: Corrected array overflow in RAID6 Xscale(R) test. ioat: fix size of 'completion' for Xen
2012-04-05Merge branch 'akpm' (Andrew's patch-bomb)Linus Torvalds
Merge batch of fixes from Andrew Morton: "The simple_open() cleanup was held back while I wanted for laggards to merge things. I still need to send a few checkpoint/restore patches. I've been wobbly about merging them because I'm wobbly about the overall prospects for success of the project. But after speaking with Pavel at the LSF conference, it sounds like they're further toward completion than I feared - apparently davem is at the "has stopped complaining" stage regarding the net changes. So I need to go back and re-review those patchs and their (lengthy) discussion." * emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches) memcg swap: use mem_cgroup_uncharge_swap fix backlight: add driver for DA9052/53 PMIC v1 C6X: use set_current_blocked() and block_sigmask() MAINTAINERS: add entry for sparse checker MAINTAINERS: fix REMOTEPROC F: typo alpha: use set_current_blocked() and block_sigmask() simple_open: automatically convert to simple_open() scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open() libfs: add simple_open() hugetlbfs: remove unregister_filesystem() when initializing module drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback fs/xattr.c:setxattr(): improve handling of allocation failures fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed fs/xattr.c: suppress page allocation failure warnings from sys_listxattr() sysrq: use SEND_SIG_FORCED instead of force_sig() proc: fix mount -t proc -o AAA
2012-04-05netdma: adding alignment check for NETDMA opsDave Jiang
This is the fallout from adding memcpy alignment workaround for certain IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align ops. Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-04-05simple_open: automatically convert to simple_open()Stephen Boyd
Many users of debugfs copy the implementation of default_open() when they want to support a custom read/write function op. This leads to a proliferation of the default_open() implementation across the entire tree. Now that the common implementation has been consolidated into libfs we can replace all the users of this function with simple_open(). This replacement was done with the following semantic patch: <smpl> @ open @ identifier open_f != simple_open; identifier i, f; @@ -int open_f(struct inode *i, struct file *f) -{ ( -if (i->i_private) -f->private_data = i->i_private; | -f->private_data = i->i_private; ) -return 0; -} @ has_open depends on open @ identifier fops; identifier open.open_f; @@ struct file_operations fops = { ... -.open = open_f, +.open = simple_open, ... }; </smpl> [akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-04-05ioatdma: DMA copy alignment needed to address IOAT DMA silicon errataDave Jiang
Silicon errata where when RAID and legacy descriptors are mixed, the legacy (memcpy and friends) operation must have alignment of 64 bytes to avoid hanging. This effects Intel Xeon C55xx, C35xx, E5-2600. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-04-05ioat: ring size variables need to be 32bit to avoid overflowDave Jiang
The alloc order can be up to 16 and 1 << 16 will over flow the 16bit integer. Change the appropriate variables to 16bit to avoid overflow. Reported-by: Jim Harris <james.r.harris@intel.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-04-04Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "Nothing too big here, just small fixes." * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM) ARM: fix bios32.c build warning ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms ARM: fix missing bug.h include in arch/arm/kernel/insn.c ARM: sa11x0: fix build errors from DMA engine API updates
2012-03-30Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6Linus Torvalds
Pull MTD changes from David Woodhouse: - Artem's cleanup of the MTD API continues apace. - Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others. - More work on DiskOnChip G3, new driver for DiskOnChip G4. - Clean up debug/warning printks in JFFS2 to use pr_<level>. Fix up various trivial conflicts, largely due to changes in calling conventions for things like dmaengine_prep_slave_sg() (new inline wrapper to hide new parameter, clashing with rewrite of previously last parameter that used to be an 'append' flag, and is now a bitmap of 'unsigned long flags'). (Also some header file fallout - like so many merges this merge window - and silly conflicts with sparse fixes) * tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits) mtd: docg3 add protection against concurrency mtd: docg3 refactor cascade floors structure mtd: docg3 increase write/erase timeout mtd: docg3 fix inbound calculations mtd: nand: gpmi: fix function annotations mtd: phram: fix section mismatch for phram_setup mtd: unify initialization of erase_info->fail_addr mtd: support ONFI multi lun NAND mtd: sm_ftl: fix typo in major number. mtd: add device-tree support to spear_smi mtd: spear_smi: Remove default partition information from driver mtd: Add device-tree support to fsmc_nand mtd: fix section mismatch for doc_probe_device mtd: nand/fsmc: Remove sparse warnings and errors mtd: nand/fsmc: Add DMA support mtd: nand/fsmc: Access the NAND device word by word whenever possible mtd: nand/fsmc: Use dev_err to report error scenario mtd: nand/fsmc: Use devm routines mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform mtd: fsmc_nand: add pm callbacks to support hibernation ...
2012-03-30ARM: sa11x0: fix build errors from DMA engine API updatesRussell King
The recent merge of the sa11x0 code into mainline had silent conflicts with further development of the DMA engine API, leading to build errors and warnings: drivers/net/irda/sa1100_ir.c: In function 'sa1100_irda_dma_start': drivers/net/irda/sa1100_ir.c:151: error: too few arguments to function 'chan->device->device_prep_slave_sg' drivers/dma/sa11x0-dma.c: In function 'sa11x0_dma_probe': drivers/dma/sa11x0-dma.c:950: warning: assignment from incompatible pointer type Fix these. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-03-29Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
Pull slave-dmaengine update from Vinod Koul: "This includes the cookie cleanup by Russell, the addition of context parameter for dmaengine APIs, more arm dmaengine driver cleanup by moving code to dmaengine, this time for imx by Javier and pl330 by Boojin along with the usual driver fixes." Fix up some fairly trivial conflicts with various other cleanups. * 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits) dmaengine: imx: fix the build failure on x86_64 dmaengine: i.MX: Fix merge of cookie branch. dmaengine: i.MX: Add support for interleaved transfers. dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages. dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'. dmaengine: imx-dma: remove unused arg of imxdma_sg_next. dmaengine: imx-dma: remove internal structure. dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure. dmaengine: imx-dma: remove 'in_use' field of 'internal' structure. dmaengine: imx-dma: remove sg member from internal structure. dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function. dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function. dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function. dmaengine: imx-dma: remove dma_mode member of internal structure. dmaengine: imx-dma: remove data member from internal structure. dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c dmaengine: at_hdmac: add slave config operation dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic dmaengine/dma_slave: introduce inline wrappers dma: imx-sdma: Treat firmware messages as warnings instead of erros ...
2012-03-28iop-adma: Corrected array overflow in RAID6 Xscale(R) test.Don Morris
Bug: cppcheck reported overflow in array assignment (for loop walks 0 to IOP_ADMA_NUM_SRC_TEST+2, array size is IOP_ADMA_NUM_SRC_TEST). Reported as: https://bugzilla.kernel.org/show_bug.cgi?id=42677 Test code pq_src array was grown by two elements to correspond with actual usage (IOP_ADMA_NUM_SRC_TEST+2), stack consumption was kept constant by modifying the pq_dest two element array which is only used when pq_src is referenced up to IOP_ADMA_NUM_SRC_TEST elements into the address of the new last two elements of the pq_src array. This is presumed to be the original intent but would be reliant on compilers always having pq_dest contiguous with the final element of pq_src. Note: This is a re-send of a request for review from two weeks ago. Looking for review (or shootdown), adding LKML to list for a wider audience. Thanks. Updated per review comments of Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: Don Morris <don.morris@hp.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-03-27Merge branch 'platforms' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM platform updates from Russell King: "This covers platform stuff for platforms I have a direct interest in (iow, I have the hardware). Essentially: - as we no longer support any other Acorn platforms other than RiscPC anymore, we can collect all that code into mach-rpc. - convert Acorn expansion card stuff to use IRQ allocation functions, and get rid of NO_IRQ from there. - cleanups to the ebsa110 platform to move some private stuff out of its header files. - large amount of SA11x0 updates: - conversion of private DMA implementation to DMA engine support (this actually gives us greater flexibility in drivers over the old API.) - re-worked ucb1x00 updates - convert to genirq, remove sa11x0 dependencies, fix various minor issues - move platform specific sa11x0 framebuffer data into platform files in arch/arm instead of keeping this in the driver itself - update sa11x0 IrDA driver for DMA engine, and allow it to use DMA for SIR transmissions as well as FIR - rework sa1111 support for genirq, and irq allocation - fix sa1111 IRQ support so it works again - use sparse IRQ support After this, I have one more pull request remaining from my current set, which I think is going to be the most problematical as it generates 8 conflicts." Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per Russell. * 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits) ARM: 7343/1: sa11x0: convert to sparse IRQ ARM: 7342/2: sa1100: prepare for sparse irq conversion ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h ARM: sa11x0: remove unused DMA controller definitions ARM: sa11x0: remove old SoC private DMA driver USB: sa1111: add hcd .reset method USB: sa1111: add OHCI shutdown methods USB: sa1111: reorganize ohci-sa1111.c USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__) USB: sa1111: sparse and checkpatch cleanups ARM: sa11x0: don't static map sa1111 ARM: sa1111: use dev_err() rather than printk() ARM: sa1111: cleanup sub-device registration and unregistration ARM: sa1111: only setup DMA for DMA capable devices ARM: sa1111: register sa1111 devices with dmabounce in bus notifier ARM: sa1111: move USB interface register definitions to ohci-sa1111.c ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c ARM: sa1111: delete unused physical GPIO register definitions ...
2012-03-27dmaengine: imx: fix the build failure on x86_64Vinod Koul
commit 6bd081277ea0 "dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c" removed the dependency in config for the imx dma driver, whereas it should depend on ARCH_MXS Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-27mxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()Huang Shijie
[1] Background : The GPMI does ECC read page operation with a DMA chain consist of three DMA Command Structures. The middle one of the chain is used to enable the BCH, and read out the NAND page. The WAIT4END(wait for command end) is a comunication signal between the GPMI and MXS-DMA. [2] The current DMA code sets the WAIT4END bit at the last one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ | | set WAIT4END here This chain works fine in the mx23/mx28. [3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should be set not only at the last DMA Command Structure, but also at the middle one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ ^ | | | | set WAIT4END here too set WAIT4END here If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state. In the next ECC write page operation, a DMA-timeout occurs. This has been catched in the MX6Q board. [4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(), and use the dma_ctrl_flags: --------------------------------------------------------- DMA_PREP_INTERRUPT : append a new DMA Command Structrue. DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure. --------------------------------------------------------- [5] changes to the relative drivers: <1> For mxs-mmc driver, just use the new flags, do not change any logic. <2> For gpmi-nand driver, and use the new flags to set the DMA chain, especially for ecc read page. Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mxs-dma : move the mxs dma.h to a more common placeHuang Shijie
Move the header to a more common place. The mxs dma engine is not only used in mx23/mx28, but also used in mx50/mx6q. It will also be used in the future chips. Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to store the Freescale's header files. change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver to the new header file. Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Acked-by: Chris Ball <cjb@laptop.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-26dmaengine: i.MX: Fix merge of cookie branch.Javier Martin
When merging DMA cookie changes a small chunk of code was dropped. This broke imx-dma driver. This patch adds this chunk again and fixes the problem. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: i.MX: Add support for interleaved transfers.Javier Martin
i.MX2 and i.MX1 chips have the possibility to do interleaved transfers with two constraints: - Only one chunk can be used (i.e. only 2D transfers are allowed). - Only 2 interleaved configurations can be applied at the same time for all channels. Since this patch adds a new resource 'slots_2d' which is shared by all the DMA channels and to avoid disgustin locking BUGs, the 'lock' member has been moved to the global 'imxdma_engine' structure. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.Javier Martin
There were some 'pr_crit' and 'pr_debug' messages due to the initial merge. Replace them by 'dev_dbg' and 'dev_warn' to be consistent. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.Javier Martin
These global variables are integrated into the dmaengine structure. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove unused arg of imxdma_sg_next.Javier Martin
Since this function is always used with 'desc' as first argument and 'desc->sg' as second argument, the latter is clearly redundant and can be removed. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove internal structure.Javier Martin
This structure was created to allow an smoothless merge but was meant to be removed. Remaining members 'hw_chaining' and 'watchdog' are moved to the channel structure. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.Javier Martin
Use per-descriptor 'len' field to keep track of the remaining bytes instead. This goes on the direction of eventually removing the 'internal' structure. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.Javier Martin
It makes no sense keeping an 'in_use' flag when the multiple descriptor mechanism already prevents a new DMA transfer to be issued when another one is in course. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove sg member from internal structure.Javier Martin
This member is redundant, because it is already present in descriptor structure. Removing it will make further removing of 'internal' structure easier. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.Javier Martin
Removing this function allows moving 'ccr_to_device' and 'ccr_from_device' from internal struct to channel struct. This repesents a step forward towards removing auxiliary 'internal' structure. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.Javier Martin
This function is only used once in the driver and uses some intermediary variables that are not needed anymore. For this reason it's been merged with 'imxdma_control'. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.Javier Martin
This function is only used once in the driver and has a lot of checks that are not needed anymore. For this reason it's been merged with 'imxdma_enable_hw'. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove dma_mode member of internal structure.Javier Martin
dmaengine now provides 'enum dma_transfer_direction' to properly specify DMA transfer direction. For this reason, DMA_MODE_* defines are replaced by this new type and therefore dma_mode member becomes redundant. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: remove data member from internal structure.Javier Martin
Internal structure is just an auxiliary structure used for the initial merge which is meant to be gone. As data member is not use anywhere we can simply remove it. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-26dmaengine: imx-dma: merge old dma-v1.c with imx-dma.cJavier Martin
It is mainly a simple merge changing the prefix of some functions to fit the imx-dma namings. As there are no users of the old dma-v1.c api we can safely remove this file. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-24Merge tag 'module-for-3.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux Pull cleanup of fs/ and lib/ users of module.h from Paul Gortmaker: "Fix up files in fs/ and lib/ dirs to only use module.h if they really need it. These are trivial in scope vs the work done previously. We now have things where any few remaining cleanups can be farmed out to arch or subsystem maintainers, and I have done so when possible. What is remaining here represents the bits that don't clearly lie within a single arch/subsystem boundary, like the fs dir and the lib dir. Some duplicate includes arising from overlapping fixes from independent subsystem maintainer submissions are also quashed." Fix up trivial conflicts due to clashes with other include file cleanups (including some due to the previous bug.h cleanup pull). * tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: lib: reduce the use of module.h wherever possible fs: reduce the use of module.h wherever possible includecheck: delete any duplicate instances of module.h
2012-03-23Merge branch 'amba' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull #2 ARM updates from Russell King: "Further ARM AMBA primecell updates which aren't included directly in the previous commit. I wanted to keep these separate as they're touching stuff outside arch/arm/." * 'amba' of git://git.linaro.org/people/rmk/linux-arm: ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver ARM: 7335/1: mach-u300: do away with MMC config files ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register ARM: 7309/1: realview: fix unconnected interrupts on EB11MP ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend ARM: 7221/1: mmc: mmci: Change from using legacy suspend ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction ARM: 7217/1: mmc: mmci: Put power register deviations in variant data ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
2012-03-23ioat: fix size of 'completion' for XenDan Williams
Starting with v3.2 Jonathan reports that Xen crashes loading the ioatdma driver. A debug run shows: ioatdma 0000:00:16.4: desc[0]: (0x300cc7000->0x300cc7040) cookie: 0 flags: 0x2 ctl: 0x29 (op: 0 int_en: 1 compl: 1) ... ioatdma 0000:00:16.4: ioat_get_current_completion: phys_complete: 0xcc7000 ...which shows that in this environment GFP_KERNEL memory may be backed by a 64-bit dma address. This breaks the driver's assumption that an unsigned long should be able to contain the physical address for descriptor memory. Switch to dma_addr_t which beyond being the right size, is the true type for the data i.e. an io-virtual address inidicating the engine's last processed descriptor. [stable: 3.2+] Cc: <stable@vger.kernel.org> Reported-by: Jonathan Nieder <jrnieder@gmail.com> Reported-by: William Dauchy <wdauchy@gmail.com> Tested-by: William Dauchy <wdauchy@gmail.com> Tested-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-03-21dmaengine: at_hdmac: add slave config operationNicolas Ferre
This patch introduces DMA_SLAVE_CONFIG to at_hdmac Atmel DMA driver. It is needed to fix a regression in the use of atmel-mci.c driver on Atmel AT91 platforms brouth by e2b35f3: "dmaengine/dw_dmac: Fix dw_dmac user drivers to adapt to slave_config changes" We remove some parts of the private structure "at_dma_slave" and use the information provided by "struct dma_slave_config": source/destination peripheral registers and access width. AT_DMA_SLAVE_WIDTH_* values used previously are not needed anymore as we now use the standard ones. Although some conversion functions are needed to match register expected values. Some AT91 sub-architecture specific files are slightly touched by this patch but it cannot be split because it can break compilation. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-21dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclicAlexandre Bounine
Add context parameter to device_prep_slave_sg() and device_prep_dma_cyclic() interfaces to allow passing client/target specific information associated with the data transfer. Modify all affected DMA engine drivers. Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-21dma: imx-sdma: Treat firmware messages as warnings instead of errosFabio Estevam
As the SDMA controller can operate without an external firmware being loaded, treat the firmware related messages as warnings rather than errors. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-20Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull trivial tree from Jiri Kosina: "It's indeed trivial -- mostly documentation updates and a bunch of typo fixes from Masanari. There are also several linux/version.h include removals from Jesper." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits) kcore: fix spelling in read_kcore() comment constify struct pci_dev * in obvious cases Revert "char: Fix typo in viotape.c" init: fix wording error in mm_init comment usb: gadget: Kconfig: fix typo for 'different' Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c" writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header writeback: fix typo in the writeback_control comment Documentation: Fix multiple typo in Documentation tpm_tis: fix tis_lock with respect to RCU Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c" Doc: Update numastat.txt qla4xxx: Add missing spaces to error messages compiler.h: Fix typo security: struct security_operations kerneldoc fix Documentation: broken URL in libata.tmpl Documentation: broken URL in filesystems.tmpl mtd: simplify return logic in do_map_probe() mm: fix comment typo of truncate_inode_pages_range power: bq27x00: Fix typos in comment ...
2012-03-16ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driverviresh kumar
For simple modules that contain a single amba_driver without any additional setup code then ends up being a block of duplicated boilerplate. This patch adds a new macro, module_amba_driver(), which replaces the module_init()/module_exit() registrations with template functions. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-03-13Merge branch 'rmk_cookie_fixes2' into nextVinod Koul
Conflicts: drivers/dma/imx-dma.c drivers/dma/pl330.c Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-03-13dmaengine: fix for cookie changes and mergeVinod Koul
Fixed trivial issues in drivers: drivers/dma/imx-sdma.c drivers/dma/intel_mid_dma.c drivers/dma/ioat/dma_v3.c drivers/dma/iop-adma.c drivers/dma/sirf-dma.c drivers/dma/timb_dma.c Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>