| Age | Commit message (Collapse) | Author |
|---|
|
The OMAP GPIO driver keeps track about GPIO pins that are
used as IRQ lines for two reasons:
1) To prevent GPIO banks to be disabled while one of their
GPIO pins are only used as an interrupt line.
2) To not allow another caller to set the GPIO pin as output.
Now gpiolib has an API to mark GPIO pins as used as IRQ lines
so the GPIO core only allows to set as output GPIO pins not
tied to an IRQ. So there is no need to have custom code for 2).
The IRQ usage still has to be maintained locally for 1) though.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The OMAP GPIO controller HW requires a pin to be configured in GPIO
input mode in order to operate as an interrupt input. Since drivers
should not be aware of whether an interrupt pin is also a GPIO or not,
the HW should be fully configured/enabled as an IRQ if a driver solely
uses IRQ APIs such as request_irq(), and never calls any GPIO-related
APIs. As such, add the missing HW setup to the OMAP GPIO controller's
irq_chip driver.
Since this bypasses the GPIO subsystem we have to ensure that another
driver won't be able to request the same GPIO pin that is used as an
IRQ and set its direction as output. Requesting the GPIO and setting
its direction as input is allowed though.
This fixes smsc911x ethernet support for tobi and igep OMAP3 boards
and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO OMAP controller pins can be used as IRQ and GPIO
independently so is necessary to keep track GPIO pins and
IRQ lines usage separately to make sure that the bank will
always be enabled while being used.
Also move gpio_is_input() definition in preparation for the
next patch that setups the controller's irq_chip driver when
a caller requests an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace a comma between expression statements by a semicolon. This changes
the semantics of the code, but given the current indentation appears to be
what is intended.
A simplified version of the semantic patch that performs this
transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is a batch of GPIO changes for v3.11. I have agreed with Grant
to take care of the pull requests for this development cycle.
No special things are happening in the GPIO tree this time (nice with
some calm) and I have been extra careful to do regression builds and
it's well boiled in -next.
GPIO changes for the v3.11 development cycle:
- Incremental development for the Langwell (Atom SoC), Xilinx, ICH
and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun, Wolfram Sang,
Tushar Behera, Sachin Kamat and Yijing Wang"
* tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (35 commits)
Gpio/trivial: replace numeric with standard PM state macros
gpiolib: remove warnning of allocations with IRQs disabled
gpio: grgpio: Staticize local symbols
gpio-langwell: remove Withney point support
gpio: ich: add GPO_BLINK support
gpio-sta2x11: Convert to use devm_ioremap_resource
gpio_msm: Convert to use devm_ioremap_resource
gpio-rcar: Use OUTDT when reading GPIOs configured as output
gpio-sta2x11: Fix potential NULL pointer dereference
gpio/omap: omap_gpio_init_context stub must be inline
gpio: msm-v1: Remove errant __devinit to fix compile
gpio: devres: make comments proper
GPIO: xilinx: Enable driver for Xilinx zynq
DT: Add documentation for gpio-xilinx
GPIO: xilinx: Use BIT macro
GPIO: xilinx: Use __raw_readl/__raw_writel IO functions
GPIO: xilinx: Add support for dual channel
GPIO: xilinx: Simplify driver probe function
gpio: sx150x: convert to use devm_* functions
MAINTAINERS: add linux-gpio mailing list
...
|
|
Commit ede4d7a5 ("gpio/omap: convert gpio irq domain to linear mapping")
converted the OMAP GPIO driver to use a linear mapping for the GPIO IRQ
domain instead of using a legacy mapping. Not using a legacy mapping has
a number of benefits but it requires the platform to support SPARSE_IRQ
which currently is not supported on OMAP1.
So this change caused a regression on OMAP1 platforms [1].
Since this issue is not present on all OMAP2+ platforms, there is no need to
revert the driver to use legacy domain mapping for all the platforms.
[1]: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg89005.html
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The bug fix 352a2d5bf "gpio/omap: ensure gpio context is initialised"
has caused a new warning for omap1_defconfig:
drivers/gpio/gpio-omap.c:1465:13: warning: 'omap_gpio_init_context' defined but not used [-Wunused-function]
static void omap_gpio_init_context(struct gpio_bank *p) {}
^
The solution is to mark the stub function as 'static inline' so
it gets left out of the build when unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit a2797be (gpio/omap: force restore if context loss is not
detectable) broke gpio support for OMAP when booting with device-tree
because a restore of the gpio context being performed without ever
initialising the gpio context. In other words, the context restored was
bad.
This problem could also occur in the non device-tree case, however, it
is much less likely because when booting without device-tree we can
detect context loss via a platform specific API and so context restore
is performed less often.
Nevertheless we should ensure that the gpio context is initialised
on the first pm-runtime resume for gpio banks that could lose their
state regardless of whether we are booting with device-tree or not.
The context loss count was being initialised on the first pm-runtime
suspend following a resume, by populating the get_count_loss_count()
function pointer after the first pm-runtime resume. To make the code
more readable and logical, initialise the context loss count on the
first pm-runtime resume if the context is not yet valid.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar<santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull GPIO changes from Grant Likely:
"The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support"
I'm pulling this despite the earlier mess. Let's hope it compiles these
days.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
gpio: grgpio: Add irq support
gpio: grgpio: Add device driver for GRGPIO cores
gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
GPIO: gpio-generic: remove kfree() from bgpio_remove call
gpio / ACPI: Handle ACPI events in accordance with the spec
gpio: lpc32xx: Fix off-by-one valid range checking for bank
gpio: mcp23s08: convert driver to DT
gpio/omap: force restore if context loss is not detectable
gpio/omap: optimise interrupt service routine
gpio/omap: remove extra context restores in *_runtime_resume()
gpio/omap: free irq domain in probe() failure paths
gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
gpio: samsung: Add terminating entry for exynos_pinctrl_ids
gpio: mvebu: add dbg_show function
MAX7301 GPIO: Do not force SPI speed when using OF Platform
gpio: gpio-tps65910.c: fix checkpatch error
gpio: gpio-timberdale.c: fix checkpatch error
gpio: gpio-tc3589x.c: fix checkpatch errors
gpio: gpio-stp-xway.c: fix checkpatch error
gpio: gpio-sch.c: fix checkpatch error
...
|
|
When booting with device-tree the function pointer for detecting context
loss is not populated. Ideally, the pm_runtime framework should be
enhanced to allow a means for reporting context/state loss and we could
avoid populating such function pointers altogether. In the interim until
a generic non-device specific solution is in place, force a restore of
the gpio bank when enabling the gpio controller.
Adds a new device-tree property for the OMAP GPIO controller to indicate
if the GPIO controller is located in a power-domain that never loses
power and hence will always maintain its logic state.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The OMAP GPIO interrupt service routine is checking each bit in the
GPIO interrupt status register to see which bits are set. It is not
efficient to check every bit especially if only a few bits are set.
Therefore, instead of checking every bit use the __ffs() function,
which returns the location of the first set bit, to find all the set
bits.
This optimisation was suggested-by and developed in collaboration
with Felipe Balbi.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
68942edb09f69b6e09522d1d346665eb3aadde49 (gpio/omap: fix wakeups
on level-triggered GPIOs) already restores the fallingdetect and
risingdetect contexts in *_runtime_resume(). These registers were
modified in *_runtime_suspend() to include even those configured
as level-triggered since only edge-triggered gpios can generate
wakeup events. Therefore, the old context restores of the same
registers present later in the code is not needed any more.
Remove them.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently the IRQ domain is not freed once allocated, in the case where
omap_gpio_probe() fails. Therefore, ensure we free the domain if the
probe does fail. Furthermore, the local variable "ret" is not needed
and so remove this.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix :
gpio/gpio-omap.c:697: ERROR: space required before the open parenthesis '('
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These functions have been introduced by commit 10a8c383 (irq: introduce
entry and exit functions for chained handlers) in asm/mach/irq.h. This
patch moves them to linux/irqchip/chained_irq.h so that generic irqchip
drivers do not rely on architecture specific header files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
For OMAP devices, if a gpio is being used as an interrupt source but has
not been requested by calling gpio_request(), a call to request_irq()
may cause the kernel hang because the gpio bank may be disabled and
hence the register access will fail. To prevent such hangs, test for
this case and warn if this is detected.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently the OMAP GPIO driver uses a legacy mapping for the GPIO IRQ
domain. This is not necessary because we do not need to assign a
specific interrupt number to the GPIO IRQ domain. Therefore, convert
the OMAP GPIO driver to use a linear mapping instead.
Please note that this also allows to simplify the logic in the OMAP
gpio_irq_handler() routine, by using irq_find_mapping() to obtain the
virtual irq number from the GPIO bank and bank index.
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
'const static ' is not a common order, better to use 'static const' instead.
building:
make EXTRA_CFLAGS=-W ARCH=arm
drivers/gpio/gpio-omap.c:1479:
warning: 'static' is not at beginning of declaration
drivers/gpio/gpio-omap.c:1485:
warning: 'static' is not at beginning of declaration
drivers/gpio/gpio-omap.c:1491:
warning: 'static' is not at beginning of declaration
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
|
|
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change was originally titled "gpio/omap: fix off-mode bug: clear debounce
clock enable mask on free/reset". The title has been updated slightly to
reflect (what should be) the final fix.
When a GPIO is freed or shutdown, we need to ensure that any debounce settings
are cleared and if the GPIO is the only GPIO in the bank that is currently
using debounce, then disable the debounce clock as well to save power.
Currently, the debounce settings are not cleared on a GPIO free or shutdown and
so during a context restore on subsequent off-mode transition, the previous
debounce values are restored from the shadow copies (bank->context.debounce*)
leading to mismatch state between driver state and hardware state.
This was discovered when board code was doing
gpio_request_one()
gpio_set_debounce()
gpio_free()
which was leaving the GPIO debounce settings in a confused state. If that GPIO
bank is subsequently used with off-mode enabled, bogus state would be restored,
leaving GPIO debounce enabled which then prevented the CORE powerdomain from
transitioning.
To fix this, introduce a new function called _clear_gpio_debounce() to clear
any debounce settings when the GPIO is freed or shutdown. If this GPIO is the
last debounce-enabled GPIO in the bank, the debounce will also be cut.
Please note that we cannot use _gpio_dbck_disable() to disable the debounce
clock because this has been specifically created for the gpio suspend path
and is intended to shutdown the debounce clock while debounce is enabled.
Special thanks to Kevin Hilman for root causing the bug. This fix is a
collaborative effort with inputs from Kevin Hilman, Grazvydas Ignotas and
Santosh Shilimkar.
Testing:
- This has been unit tested on an OMAP3430 Beagle board, by requesting a gpio,
enabling debounce and then freeing the gpio and checking the register
contents, the saved register context and the debounce clock state.
- Kevin Hilman tested on 37xx/EVM board which configures GPIO debounce for the
ads7846 touchscreen in its board file using the above sequence, and so was
failing off-mode tests in dynamic idle. Verified that off-mode tests are
passing with this patch.
V5 changes:
- Corrected author
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A pointer to "pdev->dev" is already stored in "dev", so use it in
devm_kzalloc.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/gpio/gpio-omap.c: In function 'omap_gpio_probe':
drivers/gpio/gpio-omap.c:1060: warning: assignment discards qualifiers from pointer target type
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
- New driver for AMD-8111 southbridge GPIOs
- New driver for Wolfson Micro Arizona devices
- Propagate device tree parse errors
- Probe deferral finalizations - all expected calls to GPIO will now
hopefully request deferral where apropriate
- Misc updates to TCA6424, WM8994, LPC32xx, PCF857x, Samsung MXC, OMAP
and PCA953X drivers.
Fix up gpio_idx conflicts in drivers/gpio/gpio-mxc.c
* tag 'gpio-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of_get_named_gpio_flags() return -EPROBE_DEFER if GPIO not yet available
gpiolib: Defer failed gpio requests by default
MAINTAINERS: add entry OMAP GPIO driver
gpio/pca953x: increase variables size to support 24 bit of data
GPIO: PCA953X: Increase size of invert variable to support 24 bit
gpio/omap: move bank->dbck initialization to omap_gpio_mod_init()
gpio/mxc: use the edge_sel feature if available
gpio: propagate of_parse_phandle_with_args errors
gpio: samsung: add flags specifier to device-tree binding
gpiolib: Add support for Wolfson Microelectronics Arizona class devices
gpio: gpio-lpc32xx: Add gpio_to_irq mapping
gpio: pcf857x: share 8/16 bit access functions
gpio: LPC32xx: Driver cleanup
MAINTAINERS: Add Wolfson gpiolib drivers to the Wolfson entry
gpiolib: wm8994: Convert to devm_kzalloc()
gpiolib: wm8994: Use irq_domain mappings for gpios
gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips
gpio/tca6424: merge I2C transactions, remove cast
gpio/of: fix a typo of comment message
|
|
Since the bank->dbck initialization in a one time operation there
is no need to keep this within gpio_debounce(). Therefore, moving
clk_get(bank->dbck) to omap_gpio_mod_init(). Since the value of
bank->dbck would be NULL at the beginning, this check has been
removed.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently the gpio _runtime_resume/suspend functions are calling the
get_context_loss_count() platform function if the function is populated for
a gpio bank. This function is used to determine if the gpio bank logic state
needs to be restored due to a power transition. This function will be populated
for all banks, but it should only be called for banks that have the
"loses_context" variable set. It is pointless to call this if loses_context is
false as we know the context will never be lost and will not need restoring.
For all OMAP2+ devices gpio bank-0 is in an always-on power domain and so will
never lose context. We found that the get_context_loss_count() was being called
for bank-0 during the probe and returning 1 instead of 0 indicating that the
context had been lost. This was causing the context restore function to be
called at probe time for this bank and because the context had never been saved,
was restoring an invalid state. This ultimately resulted in a crash [1].
This issue is a regression that was exposed by commit 1b1287032 (gpio/omap: fix
missing check in *_runtime_suspend()).
There are multiple bugs here that need to be addressed ...
1. Why the always-on power domain returns a context loss count of 1? This needs
to be fixed in the power domain code [2]. However, the gpio driver should not
assume the loss count is 0 to begin with.
2. The omap gpio driver should never be calling get_context_loss_count for a
gpio bank in a always-on domain. This is pointless and adds unneccessary
overhead.
3. The OMAP gpio driver assumes that the initial power domain context loss count
will be 0 at the time the gpio driver is probed. However, it could be
possible that this is not the case and an invalid context restore could be
performed during the probe. To avoid this only populate the
get_context_loss_count() function pointer after the initial call to
pm_runtime_get() has occurred. This will ensure that the first
pm_runtime_put() initialised the loss count correctly.
This patch addresses issues 2 and 3 above.
[1] http://marc.info/?l=linux-omap&m=134065775323775&w=2
[2] http://marc.info/?l=linux-omap&m=134100413303810&w=2
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Franky Lin <frankyl@broadcom.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Franky Lin <frankyl@broadcom.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
It seems that currently GPIO module is not working correctly during idle
when debounce is enabled - the system almost never responds to button
presses (observed on OMAP3530 ES2.1 and OMAP3630 ES1.2 pandora boards).
Even though wakeups are probably working, it seems that the GPIO module
itself is unable to detect input events and generate interrupts.
OMAP35x TRM also states that:
"If the debounce clock is inactive, the debounce cell gates all
input signals and thus cannot be used."
So whenever we are disabling debounce clocks (for PM or other reasons),
be sure the module's debounce feature is disabled too.
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
commit 1b1287032 (gpio/omap: fix missing check in *_runtime_suspend())
broke wakeups on level-triggered GPIOs by adding the enabled
non-wakeup GPIO check before the workaround that enables wakeups
on level-triggered IRQs, effectively disabling that workaround.
To fix, move the enabled non-wakeup GPIO check after the
level-triggered IRQ workaround.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The fix in commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()) exposed another bug in the context restore path.
Currently, the per-bank context restore happens whenever the context
loss count is different in runtime suspend and runtime resume *and*
whenever the per-bank contex_loss_count == 0:
if (context_lost_cnt_after != bank->context_loss_count ||
!context_lost_cnt_after) {
omap_gpio_restore_context(bank);
Restoring context when the context_lost_cnt_after == 0 is clearly
wrong, since this will be true until the first off-mode transition
(which could be never, if off-mode is never enabled.) This check
causes the context to be restored on *every* runtime PM transition.
Before commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()), this code was never executed in non-OFF mode, so
there were never spurious context restores happening. After that
change though, spurious context restores could happen.
To fix, simply remove the !context_lost_cnt_after check. It is not
needed.
This bug was found when noticing that the smc911x NIC on 3530/Overo
was not working, and git bisect tracked it down to this patch. It
seems that the spurious context restore was causing the smsc911x to
not be properly probed on this platform.
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
We do checking for bank->enabled_non_wakeup_gpios in order
to skip redundant operations. Somehow, the check got missed
while doing the cleanup series.
Just to make sure that we do context restore correctly in
*_runtime_resume(), the bank->workaround_enabled check is
moved after context restore. Otherwise, it would prevent
context restore when bank->enabled_non_wakeup_gpios is 0.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Both omap_gpio_suspend() and omap_gpio_resume() does programming
of wakeup_en register.
_gpio_rmw(base, bank->regs->wkup_en, 0xffffffff, 0);
_gpio_rmw(base, bank->regs->wkup_en, bank->context.wake_en, 1);
This is redundant in omap_gpio_suspend() because wakeup_en
register automatically gets initialized in _set_gpio_wakeup()
and set_gpio_trigger() while being called either from
chip.irq_set_wake() or chip.irq_set_type().
This is also redundant in omap_gpio_resume() because wakeup_en
register is programmed in omap_gpio_restore_context() called
which is called from runtime resume callback.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
commit 672e302e3c (ARM: OMAP: use edge/level handlers from generic IRQ
framework) removed retrigger support in favor of using generic IRQ
framework. This patch cleans up some unused remnants of that removal.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
There is no more need to have saved_wakeup because bank->context.wake_en
already holds that value. So getting rid of read/write operation associated
with this field.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Since we already have bank->context.wake_en to keep track
of gpios which are wakeup enabled, there is no need to have
this field any more.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Since we already have context.fallingdetect and context.risingdetect
there is no more need to have these additional fields. Also, getting
rid of extra reads associated with them.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.
Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.
Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.
Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In gpio_get(), _get_gpio_datain() and _get_gpio_dataout() get rid of
un-necessary operation to compute gpio mask. The gpio offset passed
to gpio_get() is sufficient to do that.
Here is Russell's original comment:
Can someone explain to me this:
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base + bank->regs->datain;
return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
void __iomem *reg = bank->base;
int gpio = chip->base + offset;
u32 mask = GPIO_BIT(bank, gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
Given that bank->width on OMAP is either 32 or 16, and GPIO numbers for
any GPIO chip are always aligned to 32 or 16, why does this code bother
adding the chips base gpio number and then modulo the width?
Surely this means if - for argument sake - you registered a GPIO chip
with 8 lines followed by one with 16 lines, GPIO0..7 would be chip 0
bit 0..7, GPIO8..15 would be chip 1 bit 8..15, GPIO16..23 would be
chip 1 bit 0..7.
However, if you registered a GPIO chip with 16 lines first, it would
mean GPIO0..15 would be chip 0 bit 0..15, and GPIO16..31 would be
chip 1 bit 0..15.
Surely this kind of behaviour is not intended?
Is there a reason why the bitmask can't just be (1 << offset) where
offset is passed into these functions as GPIO number - chip->base ?
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In _enable_gpio_irqbank() when bank->regs->set_irqenable is TRUE,
gpio_mask can be directly set by writing to set_irqenable register
without overwriting current value. In order to ensure the same is
stored in context.irqenable1, we must avoid overwriting it with
gpio_mask at the end of the function. Instead, update irqenable1
appropriately by OR'ing with gpio_mask.
For the case where bank->regs->set_irqenable is FALSE, irqenable1
can be directly overwritten with 'l' which holds correct computed
value.
if (bank->regs->set_irqenable) {
reg += bank->regs->set_irqenable;
l = gpio_mask;
} else {
reg += bank->regs->irqenable;
l = __raw_readl(reg);
if (bank->regs->irqenable_inv)
l &= ~gpio_mask;
else
l |= gpio_mask;
}
Make similar change for _disable_gpio_irqbank().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In omap_gpio_runtime_suspend/resume() the context save/restore should
be independent of bank->enabled_non_wakeup_gpios. This was preventing
context restore of GPIO lines which are not wakeup enabled.
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
There are two functions, _set_gpio_dataout_reg() and _set_gpio_dataout_mask()
which writes to dataout register and the dataout context must be saved.
It is missing in the first function, _set_gpio_dataout_reg(). Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The GPIO trigger parameter is of type unsigned.
enum {
IRQ_TYPE_NONE = 0x00000000,
IRQ_TYPE_EDGE_RISING = 0x00000001,
IRQ_TYPE_EDGE_FALLING = 0x00000002,
IRQ_TYPE_EDGE_BOTH = (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING),
IRQ_TYPE_LEVEL_HIGH = 0x00000004,
IRQ_TYPE_LEVEL_LOW = 0x00000008,
IRQ_TYPE_LEVEL_MASK = (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH),
IRQ_TYPE_SENSE_MASK = 0x0000000f,
IRQ_TYPE_PROBE = 0x00000010,
...
};
Even though gpio_irq_type(struct irq_data *d, unsigned type) has the right type
of parameter, the subsequent called functions set_gpio_triggering() and
set_gpio_trigger() wrongly makes it signed integer. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
There are two ways through which wakeup_en register can be programmed
using gpiolib APIs as shown below. It is seen that in the second case
in _set_gpio_wakeup(), even though bank->suspend_wakeup is updated
correctly, its value is not programmed in wakeup_en register. Fix this.
irq_set_type()->gpio_irq_type()->_set_gpio_triggering()->set_gpio_trigger()
irq_set_wake()->gpio_wake_enable()->_set_gpio_wakeup()
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
