| Age | Commit message (Collapse) | Author |
|---|
|
The patch disables non-enabled HW windows on applying
configuration, it will allow to clear windows enabled
by bootloader.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch makes sure that exynos drm framework handles deferred
probe case correctly.
Sub drivers could be probed before resources, clock, regulator,
phy or panel, are ready for them so we should make sure that exynos
drm core waits until all resources are ready and sub drivers are
probed correctly.
Chagelog v2:
- Make sure that exynos drm core tries to bind sub drivers only in case that
they have a pair: crtc and encoder/connector components should be a pair.
- Remove unnecessary patch:
drm/exynos: mipi-dsi: consider panel driver-deferred probe
- Return error type correctly.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
System hangs when FIMD registers are accessed to disable
hardware overlays. This is because of the clocks which are
not enabled before register access.
'Hardware overlay disable' is cleaned from the FIMD probe.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
In case of exynos, setting dma-burst to 16Word causes permanent
tearing for very small buffers, e.g. cursor buffer. Burst Mode
switching, which is based on overlay size is not recommended as
overlay size varies a lot towards the end of the screen. This
causes unstable DMA which results into tearing again.
Rendering small buffers with lower burst size doesn't
cause any noticable performance overhead. 128 pixel width is
selected based on mulitple experiments with exynos5 SoCs.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch separates dpi related routines from fimd.
Changelog v2:
- Rename ctx->dpi to ctx->display
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds component framework support to resolve
the probe order issue.
Until now, exynos drm had used codes specific to exynos drm
to resolve that issue so with this patch, the specific codes
are removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
If any fimd channel was already active, initializing iommu will result
in a PAGE FAULT (e.e. u-boot could have turned on the display and
not disabled it before the kernel starts). This patch checks if any
channel is active before initializing iommu and disables it.
Signed-off-by: Akshu Agrawal <akshu.a@samsung.com>
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch removes unused vidcon0 field from fimd_context structure.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch adds parallel output interface to FIMD device driver.
It also restores support for panels initialized by boot loader,
but without proper kernel driver.
Driver uses video interface bindings to find connected panel.
It uses drm_panel interface to interact with the panel.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch corrects porch calculation. It should
be calculated as a difference between adjacent
respective fields of drm_display_mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch removes all of the suspend/resume logic from the individual
drivers and consolidates it in drm_drv. This consolidation reduces the
number of functions which enable/disable the hardware to just one -- the
dpms callback. This ensures that we always power up/down in a consistent
manner.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch separates the fimd_activate function into poweron/poweroff
functions to be more consistent with the other drivers in exynos drm. It
also properly cleans up after failures in poweron. The functions have
also been shuffled around such that they are all in the same
spot in the file and poweron/poweroff can be called from the dpms function.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch moves the exynos_drm_display implementation from fimd into
the dp driver. This will allow for tighter integration of the dp driver
into the exynos drm driver.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch removes a few fimd_context members which are either entirely
unused or unneeded.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch uses the mode passed into mode_set to configure fimd instead
of directly using the panel from context. This will allow us to move
the exynos_drm_display implementation out of fimd, where it doesn't
belong.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch splits display and manager from subdrv. The result is that
crtc functions can directly call into manager callbacks and encoder
functions can directly call into display callbacks. This will allow
us to remove the exynos_drm_hdmi shim and support mixer/hdmi & fimd/dp
with common code.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch renames the display_op power_on to dpms to accurately reflect
what the function does.
The side-effect of this patch is that the new hdmi dpms callback is now
invoked twice in the dpms path. This is safe and will be dealt with when
the exynos_drm shim goes away.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch removes the apply() manager callback in favor of putting the
relevant commits in the individual drivers. This will mitigate some of
the difference between the suspend/resume path and the dpms path
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch changes the manager ops callbacks from accepting the subdrv
device pointer to taking a pointer to the manager. This will allow us
to move closer to decoupling manager/display from subdrv, and subsequently
decoupling the crtc/plane from the encoder.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch implements the intitialize manager op in fimd. This will
allow us to keep track of drm_dev in context instead of using subdev,
which in turn makes it easier to remove subdev from fimd.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch merges overlay_ops into manager_ops. In all cases,
overlay_ops is implemented in the same place as manager ops, it doesn't
serve a functional purpose, and doesn't make things more clear.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
DRM_HZ and DRM_WAKEUP macros are removed, but they still remained.
So this patch fixes build errors by replacing the macros.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Less yelling ftw!
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixed a trivial typo.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch moves platfrom_data and device tree parsing
to separate function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch adds code to get signal polarization setting
from device tree display-timings node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The patch replaces all occurrences of struct fb_videomode by
more accurate struct videomode. The change allows to remove
mode conversion function and simplifies clock divider calculation.
Clock configuration is moved to separate function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch checks if a requested window supports alpha channel or not.
In case of s3c64xx, window 0 doesn't support alpha channel so if
the request pixel format is ARGB8888 then change it to XRGB8888.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This patch fixes wrong pixel format setting.
A pixel format is decided according to bpp and depth, or user-requested
format but fimd driver considered only bpp value to decide a proper pixel
format. So this patch makes a proper pixel format to be set according
to drm_framebuffer's pixel_format which is set by addfb with bpp and
depth, or addfb2 with user-requested format.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
kzalloc already has built-in error messages. Hence remove
additional ones.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Add of.h explicitly for of_* APIs.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Remove module.h header file inclusion from files since they do
not use/refer to any code from that file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch removes all MODULE_DEVICE_TABLE declarations.
Exynos drm drivers don't need to create MODULE_DEVICE_TABLE
yet because all devices of Exynos drm include in one SoC so
they cannot be plugged in as of now.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This patch removes tracking log functions which were used to debug
in the early development stage and are not so important as were.
So remove them for code clean up.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch renames check_timing to check_mode and removes the
unnecessary conversion of drm_display_mode to/from fb_videomode in
the hdmi driver.
v4:
1) Changed the commit message to add information related to renaming
the callbacks to check_mode.
2) Changed debug message to print 1/0 for interlace mode.
v3:
1) Replaced check_timing callbacks with check_mode.
2) Change the type of second parameter of check_mode callback from void
pointer paramenter to struct drm_display_mode pointer.
v2:
1) Removed convert_to_video_timing().
2) Corrected DRM_DEBUG_KMS to print the resolution properly.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The FIMD block present on S3C6400/S3C6410 SoCs is compatible with this
driver, so it can be supported by it as well.
This patch adds appropriate device IDs and driver data to enable this
driver for S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Some platforms that can be supported this driver has additional clock
source selection bits in VIDCON0 register that allows to select which
clock should be used to drive the pixel clock: bus clock or special
clock.
Since this driver assumes that special clock always drives the pixel
clock, this patch sets the selection bitfield to use the special clock.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Some platforms that can be supported with this driver have PRTCON
register instead of SHADOWCON, which requires slightly different
handling.
This patch factors out all register shadow control code from the driver
and adds a function to control register shadowing appropriately,
depending on driver data.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds pointer to driver data to fimd_context structure, to
remove the need to call drm_fimd_get_driver_data() each time access to
driver data is necessary.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Valid values for FIMD windows are from 0 to WINDOWS_NR-1
inclusive (5 windows in total). The WINDOWS_NR is also
a size of fimd_context.win_data array.
However, early-return tests for wrong values of windows
accepted a value of WINDOWS_NR which is out of bound
for fimd_context.win_data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Struct device pointer got from platform device pointer is already
alsigned as variable, but some functions do not use device pointer.
So this patch replaces thoes usages.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Common Clock Framework introduced the need to prepare clocks before
enabling them, otherwise clk_enable() fails. This patch adds clk_prepare_enable
and clk_disable_unprepare() calls to the driver.
This patch also removes clk_disable() from fimd_remove() as it will be done
by pm_runtime_put_sync.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This reverts commit b4e3a3e844a0e33cf106a1c9f27ff93340c37640.
|
|
While migrating to common clock framework (CCF), I found that the FIMD clocks
were pulled down by the CCF.
If CCF finds any clock(s) which has NOT been claimed by any of the
drivers, then such clock(s) are PULLed low by CCF.
Calling clk_prepare() for FIMD clocks fixes the issue.
This patch also replaces clk_disable() with clk_unprepare() during exit, since
clk_prepare() is called in fimd_probe().
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Replaces the "platform_get_resource() for IORESOURCE_IRQ" with
platform_get_resource_byname().
Both in exynos4 and exynos5, FIMD IP has 3 interrupts in the order: "fifo",
"vsync", and "lcd_sys".
But The FIMD driver expects the "vsync" interrupt to be mentioned as the
1st parameter in the FIMD DT node. So to meet this expectation of the
driver, the FIMD DT node was forced to be made by keeping "vsync" as the
1st paramter.
For example in exynos4, the FIMD DT node has interrupt numbers
mentioned as <11, 1> <11, 0> <11, 2> keeping "vsync" as the 1st paramter.
This patch fixes the above mentioned "hack" of re-ordering of the
FIMD interrupt numbers by getting interrupt resource of FIMD by using
platform_get_resource_byname().
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Add support for parsing the display-timing node using video helper
function.
The DT node parsing is done only if 'dev.of_node'
exists and the NON-DT logic is still maintained under the 'else' part.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Calculate the correct address offset values for alpha and color key
control registers based on exynos4 and exynos5 user manuals.
Also remove VIDOSD_C_SIZE_W0 macro and fix comments about registers for
size and alpha.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
