| Age | Commit message (Collapse) | Author |
|---|
|
ironlake_fdi_compute_config() already checks that we have enough
FDI bandwidth. And it doesn't just use a hardcoded value but takes
into account factors such as the actual FDI frequency, shared FDI
B/C lanes, etc.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For DP pll settings, there is only two golden configs. Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.
v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The spec says to notify prior to power down and after power up. It is
unclear whether it makes a difference.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
DPLL is not needed for DSI
v2: Rebase due to added DSI PLL assertion patch.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For DSI, we need to be asserting DSI PLL, not DPLL.
This is a somewhat stopgap implementation. It's slightly ugly to have to
pass the dsi parameter to intel_enable_pipe().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The dpll actually runs at the port clock so we don't need
to multiply it again with the pixel multiplier to get the
adjusted_mode.clock. This is in contrast to the ironlake
pixel clock readout code which uses the fdi dotclock: That
one does _not_ run with multiplied pixels.
This issue goes back to the original clock readout code added
in
commit f1f644dc66cbaf5a4c7dcde683361536b41885b9
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 27 00:39:25 2013 +0300
drm/i915: get mode clock when reading the pipe config v9
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is intended to add VGA arbiter support for Intel HD graphics on
Core processors. The old GMCH registers no longer exist, so even
though it appears that i915 participates in VGA arbitration, it doesn't
work. On Intel HD graphics we already attempt to disable VGA regions
of the device. This makes registering as a VGA client unnecessary since
we don't intend to operate differently depending on how many VGA devices
are present. We can disable VGA memory regions by clearing the memory
enable bit in the VGA MSR. That only leaves VGA IO, which we update
the VGA arbiter to know that we don't participate in VGA memory
arbitration. We also add a hook on unload to re-enable memory and
reinstate VGA memory arbitration.
v3: Use explicit LEGACY_IO | LEGACY_MEM when restoring rather than
LEGACY_MASK, per Ville's comments.
v2: I915_READ/WRITE accessors don't work in i915_disable_vga, use inb/outb
directly. Also, on the driver unbind VGA enable path, acquire legacy
IO to re-enable VGA memory. Correct comment.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add patch changelog. Also squash in a fixup to have a dummy
static inline for vga_set_legacy_decoding for CONFIG_VGA_ARB=n as
reported by the 0-day kernel build bot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
fixup 2
|
|
We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.
Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
into drm-next
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-next
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
|
|
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|
|
If we don't use the return value of a mmio read our coding style is to
use the POSTING_READ macro. This avoids cluttering the mmio traces.
While at it add the missing posting read in the lcpll enable function
that Paulo spotted.
v2: Drop the _NOTRACE changes, tracing such wait_for loops in the modeset
code might actually be rather useful!
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We currently only enter PC8+ after all its required conditions are
met, there's no rendering, and we stay like that for at least 5
seconds.
I chose "5 seconds" because this value is conservative and won't make
us enter/leave PC8+ thousands of times after the screen is off: some
desktop environments have applications that wake up and do rendering
every 1-3 seconds, even when the screen is off and the machine is
completely idle.
But when I was testing my PC8+ patches I set the default value to
100ms so I could use the bad-behaving desktop environments to
stress-test my patches. I also thought it would be a good idea to ask
our power management team to test different values, but I'm pretty
sure they would ask me for an easy way to change the timeout. So to
help these 2 cases I decided to create an option that would make it
easier to change the default value. I also expect people making
specific products that use our driver could try to find the perfect
timeout for them.
Anyway, fixing the bad-behaving applications will always lead to
better power savings than just changing the timeout value: you need to
stop waking the Kernel, not quickly put it back to sleep again after
you wake it for nothing. Bad sleep leads to bad mood!
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.
The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.
For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.
This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.
v2: (this is not really v2, many previous versions were already sent,
but they had different names)
- Use the new functions to enable/disable GTIMR and GEN6_PMIMR
- Rename almost all variables and functions to names suggested by
Chris
- More WARNs on the IRQ handling code
- Also disable PC8 when there's GPU work to do (thanks to Ben for
the help on this), so apps can run caster
- Enable PC8 on a delayed work function that is delayed for 5
seconds. This makes sure we only enable PC8+ if we're really
idle
- Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
- Replace some DRM_ERRORs with WARNs
- Fix calls to restore GT and PM interrupts
- Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
- Move the force_wake chunk to its own patch
- Only restore what's missing from RC6, not everything
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This was causing WARNs in one machine, so instead of trying to guess
exactly which hotplug bits should exist, just do the test on the
non-HPD bits. We don't care about the state of the hotplug bits, we
just care about the others, that need to be 1.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If LCPLL is disabled, there's a chance we might be in package C8 state
or deeper, and we'll get a hard hang when restoring LCPLL (also, a red
led lights up on my motherboard). So grab the force_wake, which will
get us out of RC6 and, as a consequence, out of PC8+ (since we need
RC6 to get into PC8+).
Note: Discussions with hw designers are still ongoing what exactly
goes boom here. But I think we can go ahead and just merge this little
hack for now until it's clear what we actually need.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add small note about the current state of the discussion
around this hack.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The existing code was trying different vswing and preemphasis settings
in the wrong place, and wasn't trying them enough. So add a loop to
walk through them, properly disabling FDI TX and RX in between if a
failure is detected.
v2: remove unneeded reg writes, add delays around bit lock checks (Jesse)
v3: fix TX and RX disable per spec (Paulo)
fix delays per spec (Paulo)
make RX symbol lock check match TX bit lock check (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51983
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Whenever I need to work with the HSW_PWER_WELL_* register bits I have
to look at the documentation to find out which bit is to request the
power well and which one shows its current state. Rename the bits so I
won't need to look the docs every time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the power well is disabled VGA is guaranteed to be disabled.
This fixes unclaimed register messages that happen on suspend/resume.
v2: Check the actual hw power well state instead of our own tracking
to make sure VGA is _really_ off (in case the BIOS/KVMr has just its
own request bit set). Requested by Ville.
Note: Ville suggested whether it wouldn't be better to just enable the
power well over a slightly longer time in our resume code, since we
already do that. I tend to agree, but there's also the modeset force
code in the lid notifier which _also_ eventually calls redisable_vga.
We shouldn't ever need this on somewhat modern hw (everything with
opregion essentially) but the code to bail out isn't there. Hence
stick with this simple approach here for now.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67517
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Summarize the discussion around the resume sequence and lid
notifier a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
After computing the stage changes for the set_config, record those in
the debug log.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Caught by "make W=1 drivers/gpu/drm/i915/".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If we get an error event really early in the driver setup sequence,
which gen3 is especially prone to with various display GTT faults we
Oops. So try to avoid this.
Additionally with Haswell the transcoders are a separate bank of
registers from the pipes (4 transcoders, 3 pipes). In event of an
error, we want to be sure we have a complete and accurate picture of
the machine state, so record all the transcoders in addition to all
the active pipes.
This regression has been introduced in
commit 702e7a56af3780d8b3a717f698209bef44187bb0
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Oct 23 18:29:59 2012 -0200
drm/i915: convert PIPECONF to use transcoder instead of pipe
Based on the patch "drm/i915: Dump all transcoder registers on error"
from Chris Wilson:
v2: Rebase so that we don't try to be clever and try to figure out the
cpu transcoder from hw state. That exercise should be done when we
analyze the error state offline.
The actual bugfix is to not call intel_pipe_to_cpu_transcoder in the
error state capture code in case the pipes aren't fully set up yet.
v3: Simplifiy the err->num_transcoders computation a bit. While at it
make the error capture stuff save on systems without a display block.
v4: Fix fail, spotted by Jani.
v5: Completely new commit message, cc: stable.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60021
Cc: stable@vger.kernel.org
Tested-by: Dustin King <daking@rescomp.stanford.edu>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The display engine has unique coherency rules such that it requires
special handling to ensure that all writes to cursors, scanouts and
sprites are clflushed. This patch introduces the infrastructure to
simply track when an object is being accessed by the display engine.
v2: Explain the is_pin_display() magic as the sources for obj->pin_count
and their individual rules is not obvious. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port. Fix
that up by enumerating both ports if possible.
Tested-by: "Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Caught by the dead code police!
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
And also fix a small typo in the intel_encoder_dpms() comment.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The SDVO code tries to compare the encoder's and crtc's idea of the
pixel_multiplier. Normally they have to match, but when transitioning
to DPMS off, we turn off the pipe before reading out the pipe_config,
so the pixel_multiplier in the pipe_config will be 0, whereas the
encoder will still have its pixel_multiplier set to whatever value we
were using when the display was active. This leads to a warning
from intel_modeset_check_state().
WARNING: CPU: 1 PID: 2846 at drivers/gpu/drm/i915/intel_sdvo.c:1378 intel_sdvo_get_config+0x158/0x160()
SDVO pixel multiplier mismatch, port: 0, encoder: 1
Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep
CPU: 1 PID: 2846 Comm: Xorg Not tainted 3.11.0-rc3-00208-gbe1e8d7-dirty #19
Hardware name: Apple Computer, Inc. Macmini1,1/Mac-F4208EC8, BIOS MM11.88Z.0055.B03.0604071521 04/07/06
00000000 00000000 ef0afa54 c1597bbb c1737ea4 ef0afa84 c10392ca c1737e6c
ef0afab0 00000b1e c1737ea4 00000562 c12dfbe8 c12dfbe8 ef0afb14 00000000
f697ec00 ef0afa9c c103936e 00000009 ef0afa94 c1737e6c ef0afab0 ef0afadc
Call Trace:
[<c1597bbb>] dump_stack+0x41/0x56
[<c10392ca>] warn_slowpath_common+0x7a/0xa0
[<c103936e>] warn_slowpath_fmt+0x2e/0x30
[<c12dfbe8>] intel_sdvo_get_config+0x158/0x160
[<c12c3220>] check_crtc_state+0x1e0/0xb10
[<c12cdc7d>] intel_modeset_check_state+0x29d/0x7c0
[<c12dfe5c>] intel_sdvo_dpms+0x5c/0xa0
[<c12985de>] drm_mode_obj_set_property_ioctl+0x40e/0x420
[<c1298625>] drm_mode_connector_property_set_ioctl+0x35/0x40
[<c1289294>] drm_ioctl+0x3e4/0x540
[<c10fc1a2>] do_vfs_ioctl+0x72/0x570
[<c10fc72f>] SyS_ioctl+0x8f/0xa0
[<c159b7fa>] sysenter_do_call+0x12/0x22
---[ end trace 7ce940aff1366d60 ]---
Fix the problem by skipping the encoder get_config() function for
inactive encoders.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Rather than open-code the teardown of a framebuffer, export the routine
from intel_display.c. This then make intel_fbdev symmetric in its use of
the common intel_framebuffer routines to initialise and clean up the
struct intel_framebuffer. (And new features need only be added in one
location!)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Userspace can pass a mode with an unspecified vsync/hsync polarity
setting. All encoders in the Intel driver take this to mean a negative
polarity setting. The HW readout/state checker code on the other hand
needs these flags to be explicitly set, otherwise the state checker will
WARN about the mismatch.
Get rid of the WARN by making the polarity setting explicit in the
adjusted mode flags based on the requested mode flags. This will keep
the existing behavior otherwise.
Note that we could guess from the other timing parameters whether the
user wanted a VESA or other standard mode and set the polarity
accordingly. This is what the NV driver does
(drivers/gpu/drm/nouveau/dispnv04/crtc.c), but I think that's not very
exact and would change the existing behavior of the Intel driver.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65442
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: cancan,feng <cancan.feng@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
VLV wants encoder enabling before the pipe is up. With the previously
rearranged VLV DP and HDMI ->pre_enable and ->enable callbacks in place,
this no longer depends on the early ->enable hook call. Move the
->enable call at the end of the sequence, similar to the crtc enable on
other platforms. This will be needed e.g. for moving the eDP backlight
enabling to the right place in the sequence, currently done too early on
VLV.
There should be no functional changes.
v2: Rebase.
v3: Explain why this is needed in the commit message (Chris).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Otherwise we get flooded by the kernel warning us that we are doing
long sequences of IO without serialisation. For example,
WARNING: CPU: 0 PID: 11136 at drivers/gpu/drm/i915/intel_sideband.c:40 vlv_sideband_rw+0x48/0x1ef()
Modules linked in:
CPU: 0 PID: 11136 Comm: kworker/u2:0 Tainted: G W 3.11.0-rc2+ #4
Call Trace:
[<c2028564>] ? warn_slowpath_common+0x63/0x78
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c20285dd>] ? warn_slowpath_null+0xf/0x13
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c227b060>] ? vlv_dpio_write+0x1c/0x21
[<c2262b3b>] ? intel_dp_set_signal_levels+0x24a/0x385
[<c2264909>] ? intel_dp_complete_link_train+0x25/0x1d1
[<c2264c55>] ? intel_dp_check_link_status+0xf7/0x106
[<c2238ced>] ? i915_hotplug_work_func+0x17b/0x221
[<c203a204>] ? process_one_work+0x12e/0x210
[<c203a5e4>] ? worker_thread+0x116/0x1ad
[<c203a4ce>] ? rescuer_thread+0x1cb/0x1cb
[<c203d8f5>] ? kthread+0x67/0x6c
[<c2457ebb>] ? ret_from_kernel_thread+0x1b/0x30
[<c203d88e>] ? init_completion+0x18/0x18
v2: Retire the locking in vlv_crtc_enable() and do it close to the meat.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Squash in a s/mutex_lock/mutex_unlock/ fixup spotted by the 0
day kernel build/coccinelle and reported by Dan Carpenter.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Art confirms that this should work fine. Since most panels are 18bpp
with dithering from 24bpp, the existing code wouldn't be enabled in most
cases.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In the old days of the crtc helpers we've only had the encoder and
crtc ->mode_fixup callbacks. So when the lvds connector wanted to
adjust the crtc timings it had to set a driver-private mode flag to
tell the crtc mode fixup code to not overwrite them with the generic
ones.
When converting things to the new infrastructure I've kept the entire
logic and only moved the flag to pipe_config->timings_set. But this
logic is pretty tricky and already caused regressions:
commit 21d8a4756af5fdf4a42e79a77cf3b6f52678d443
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 08:07:30 2013 +0200
drm/i915: fix pfit regression for non-autoscaled resolutions
So take advantage of the flexibility our own modeset infrastructure
affords us and prefill default crtc timings. This allows us to rip out
->timings_set. Note that we overwrite things again when retrying the
pipe config computation due to bandwidth constraints to avoid bogus
crtc timings if the encoder only does relative adjustments (which is
how the pfit code works). Only a theoretical concern though since
platforms where we retry (pch-split platforms) do not need
adjustements (since only the old gmch pfit needs that). But let's
better be safe than sorry.
Since we now initialize the crtc timings before calling the
encoder->compute_config functions the crtc initialization in the gmch
pfit code is now redudant and so can be removed.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add a paragraph to the commit message to explain why we can
ditch the crtc timings initialization call from the gmch pfit code, to
answer a question from Rodrigo's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The encoder->mode_set callback from the crtc helpers is now completely
unused in our driver. Good riddance!
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Everyone is now using our own ->compute_config callback, which means
we can now also make that callback mandatory.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We need the correct clock to accurately assess whether we need to
enable the double wide pipe mode or not.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Stuart Abercrombie <sabercrombie@google.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.
v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://people.freedesktop.org/~airlied/linux'
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218ba18fcde11ef0e22b07e6365645788
Merge: 42577ca 058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea2f341b626b255d9898a5ca5fabbf0a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.
Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:
Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.
The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.
v2: - Rebase.
- Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
- Remove/add a useless/needed POSTING_READ (Ben)
- Early return in case LCPLL is already restored (Ben)
- Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
- Add interrupt assertions (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We currently don't support HDMI clock bending nor use SSC for DP or
HDMI on Haswell, so the only case where we need CLKOUT_DP is for VGA.
v2: - Replace the IS_ULT check for LPT-LP
- Simplify GEN0/DBUFF0 check due to change on the previous patch
- Also check for SBI_SSCCTL_DISABLE (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now it implements 3 different sequences from BSpec and also has
support for ULT.
v2: - Change IS_ULT checks for LPT-LP checks
- Add check for LPT-LP + with_fdi (Ben)
- Merge DBUFF0/GEN0 bit definitions since they're the same
register (Ben)
- DBUFF0 (1<<0) is Disable, not Enable
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=47941
BugLink: https://bugs.launchpad.net/bugs/1163720
BugLink: https://bugs.launchpad.net/bugs/1162026
Some machines suffer from non-functional backlight controls if
BLM_PCH_PWM_ENABLE is set, so provide a quirk to avoid doing so.
Apply this quirk to Dell XPS 13 models.
Tested-by: Eric Griffith <EGriffith92@gmail.com>
Tested-by: Kent Baxley <kent.baxley@canonical.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The next step is to modify lpt_enable_clkout_dp to enable support for
"Sequence to enable CLKOUT_DP" and "Sequence to enable CLKOUT_DP
without spread".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Because lpt_init_pch_refclk implements the "Sequence to enable
CLKOUT_DP for FDI usage and configure PCH FDI I/O", which is very
similar to "Sequence to enable CLKOUT_DP" and "Sequence to enable
CLKOUT_DP without spread". With the extracted functions we can more
easily implement the two missing sequences.
v2: Rebase (WaMPhyProgramming:hsw comment).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The machines that fall in the "is_sdv" case are some very early
pre-production steppings. This patch may break VGA output after
suspend/resume on these machines.
Even the documentation for the is_sdv cases was removed from BSpec.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
PSR must be enabled after transcoder and port are running.
And it is only available for HSW.
v2: move enable/disable to intel_ddi
v3: The spec suggests PSR should be disabled even before backlight (by pzanoni)
v4: also disabling and enabling whenever panel is disabled/enabled.
v5: make it last patch to avoid breaking whenever bisecting. So calling for
update and force exit came to this patch along with enable/disable calls.
v6: Remove unused and unecessary psr_enable/disable calls, as notice by Paulo.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the psr exit code in the busy ioctl since I didn't merge
that part of the infrastructure yet - it needs more thought.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
