| Age | Commit message (Collapse) | Author |
|---|
|
The BLC_PWM_CTL2 register does not exist before gen4. While at it, do a
slight drive by cleanup of the code.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
But disabled by default. This essentially reverts
commit bcd5023c961a44c7149936553b6929b2b233dd27
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Mar 14 14:17:55 2011 +1000
drm/i915: disable opregion lid detection for now
but leaves the autodetect mode disabled. There's also the explicit lid
status option added in
commit fca874092597ef946b8f07031d8c31c58b212144
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Feb 17 13:44:48 2011 +0000
drm/i915: Add a module parameter to ignore lid status
Which overloaded the meaning for the panel_ignore_lid parameter even
more. To fix up this mess, give the non-negative numbers 0,1 the
original meaning back and use negative numbers to force a given state.
So now we have
1 - disable autodetect, return unknown
0 - enable autodetect
-1 - force to disconnected/lid closed
-2 - force to connected/lid open
v2: My C programmer license has been revoked ...
v3: Beautify the code a bit, as suggested by Chris Wilson.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27622
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
into drm-next
Daniel writes:
Highlights of this -next round:
- ivb fdi B/C fixes
- hsw sprite/plane offset fixes from Damien
- unified dp/hdmi encoder for hsw, finally external dp support on hsw
(Paulo)
- kill-agp and some other prep work in the gtt code from Ben
- some fb handling fixes from Ville
- massive pile of patches to align hsw VGA with the spec and make it
actually work (Paulo)
- pile of workarounds from Jesse, mostly for vlv, but also some other
related platforms
- start of a dev_priv reorg, that thing grew out of bounds and chaotic
- small bits&pieces all over the place, down to better error handling for
load-detect on gen2 (Chris, Jani, Mika, Zhenyu, ...)
On top of the previous pile (just copypasta):
- tons of hsw dp prep patches form Paulo
- round scheduled work items and timers to nearest second (Chris)
- some hw workarounds (Jesse&Damien)
- vlv dp support and related fixups (Vijay et al.)
- basic haswell dp support, not yet wired up for external ports (Paulo)
- edp support (Paulo)
- tons of refactorings to prepare for the above (Paulo)
- panel rework, unifiying code between lvds and edp panels (Jani)
- panel fitter scaling modes (Jani + Yuly Novikov)
- panel power improvements, should now work without the BIOS setting it up
- extracting some dp helpers from radeon/i915 and move them to
drm_dp_helper.c
- randome pile of workarounds (Damien, Ben, ...)
- some cleanups for the register restore code for suspend/resume
- secure batchbuffer support, should enable tear-free blits on gen6+
Chris)
- random smaller fixlets and cleanups.
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (231 commits)
drm/i915: Restore physical HWS_PGA after resume
drm/i915: Report amount of usable graphics memory in MiB
drm/i915/i2c: Track users of GMBUS force-bit
drm/i915: Allocate the proper size for contexts.
drm/i915: Update load-detect failure paths for modeset-rework
drm/i915: Clear unused fields of mode for framebuffer creation
drm/i915: Always calculate 8xx WM values based on a 32-bpp framebuffer
drm/i915: Fix sparse warnings in from AGP kill code
drm/i915: Missed lock change with rps lock
drm/i915: Move the remaining gtt code
drm/i915: flush system agent TLBs on SNB
drm/i915: Kill off now unused gen6+ AGP code
drm/i915: Calculate correct stolen size for GEN7+
drm/i915: Stop using AGP layer for GEN6+
drm/i915: drop the double-OP_STOREDW usage in blt_ring_flush
drm/i915: don't rewrite the GTT on resume v4
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
drm/i915: put ring frequency and turbo setup into a work queue v5
drm/i915: don't block resume on fb console resume v2
drm/i915: extract l3_parity substruct from dev_priv
...
|
|
dev_priv has grown way too big, and grouping memebers into substructs
and moving them out of line helps re-gain some overview.
Unfortunatley I couldn't just call the substruct save and drop the prefix, since
that will make most member names clash with registers #defines. Changes in
i915_drv.h done by hand, everything else changed with
s/\<save\([A-Z]*\)/regfile.save\1/ in vim.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
commit 28dcc2d60cb570d9f549c329b2f51400553412a1
Author: Jani Nikula <jani.nikula@intel.com>
Date: Mon Sep 3 16:25:12 2012 +0300
drm/i915: do not expose a dysfunctional backlight interface to userspace
prevents backlight interface creation if the BIOS has not set the backlight
PWM CTL registers that contain the max PWM value. It's apparently normal on
those machines, so demote the message about it to debug level.
Reported-by: Orion Poplawski <orion@cora.nwra.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56330
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pave the way for sharing some logic between eDP and LVDS.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Create a generic struct intel_panel for sharing a data structure and code
between eDP and LVDS panels. Add the new struct to intel_connector so that
later on we can have generic EDID and mode reading functions with EDID
caching that transparently fallback to fixed mode when EDID is not
available.
Add intel_panel as a dummy first, and move data (such as the mentioned
fixed mode) to it in later patches.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup tiny conflict in intel_dp_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Get rid of saved int_lvds_connector and int_edp_connector in
drm_i915_private.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Previously intel_panel_setup_backlight() would create a sysfs backlight
interface with max brightness of 1 if it was unable to figure out the max
backlight brightness. This rendered the backlight interface useless.
Do not create a dysfunctional backlight interface to begin with.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When you reopen the lid on a laptop with PCH, the panel suddenly goes
blank sometimes. It seems because BLC_PWM_CPU_CTL register is cleared
to zero when BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1 registers are
enabled.
This patch fixes the problem by moving the call of the function setting
BLC_PWM_CPU_CTL after enabling other two registers.
Reported-and-tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This function isn't used outside of intel_panel.c, so make it static.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When we enable/disable the CPU backlight registers we can't forget to
enable/disable the PCH backlight registers. Since we're using the CPU
registers we should also unset the override bit.
Fixes a regression on the following commit:
drm/i915: properly enable the blc controller on the right pipe
The commit just deleted the code that sets the PCH registers, so it
was relying on the values set by the BIOS. I told my BIOS to boot on
the DVI monitor instead of the LVDS panel, so I noticed the bug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On gen4+ we have a bitfield to specify from which pipe the backlight
controller should take it's clock. For PCH split platforms we've
already set these up, but only at initialization time. And without
taking into account the 3rd pipe added with ivb.
For gen4, we've completely ignored these. Although we do restrict lvds
to the 2nd pipe, so this is only a problem on machines where we boot
up with the lvds on the first pipe.
So restructure the code to enable the backlight on the right pipe at
modeset time.
v2: For odd reasons panel_enable_backlight gets called twice in a
modeset, so we can't WARN_ON in there if the backlight controller is
switched on already.
v3: backlight enable can also be called through dpms on, so the check
in there is legit. Update the comment to reflect that.
Tested-By: Kamal Mostafa <kamal@canonical.com>
Bugzilla: https://bugs.launchpad.net/bugs/954661
Cc: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.
After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.
Also mark the mode argument of pch_panel_fitting const.
v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The power field was never correctly initialized.
[airlied: just took the two drm specific bits]
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This regression has been introduced in
commit ca9bfa7eed20ea34e862804e62aae10eb159edbb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Use a more current logging style. Ensure that appropriate
logging messages are prefixed with "i915: ".
Convert printks to pr_<level>. Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
A machine may need to invert the panel backlight brightness value. This
patch adds the infrastructure for a quirk to do so.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Following the documentation of the Legacy Backlight Brightness (LBB)
Register in the configuration space of some Intel PCI graphics adapters,
setting the LBB register with the value 0x0 causes the backlight to be
turned off, and 0xFF causes the backlight to be set to 100% intensity
(http://download.intel.com/embedded/processors/Whitepaper/324567.pdf).
The Acer Aspire 5734Z, however, turns the backlight off at 0xFF and sets
it to maximum intensity at 0. In consequence, the screen of this systems
becomes dark at an early boot stage which makes it unusable. The same
inversion applies to the BLC_PWM_CTL I915 register. This problem was
introduced in kernel version 2.6.38 when the PCI device of this system
was first supported by the i915 KMS module.
This patch adds a parameter to the i915 module to enable inversion of
the brightness variable (i915.invert_brightness).
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We have a pretty decent confusion about vertical timings of interlaced
modes. Peter Ross has written a patch that makes interlace modes work
on a lot more platforms/output combinations by doubling the vertical
timings.
The issue with that patch is that core drm _does_ support specifying
whether we want these vertical timings in fields or frames, we just
haven't managed to consistently use this facility. The relavant
function is drm_mode_set_crtcinfo, which fills in the crtc timing
information.
The first thing to note is that the drm core keeps interlaced modes in
frames, but displays modelines in fields. So when the crtc modeset
helper copies over the mode into adjusted_mode it will already contain
vertical timings in half-frames. The result is that the fixup code in
intel_crtc_mode_fixup doesn't actually do anything (in most cases at
least).
Now gen3+ natively supports interlaced modes and wants the vertical
timings in frames. Which is what sdvo already fixes up, at least under
some conditions.
There are a few other place that demand vertical timings in fields
but never actually deal with interlaced modes, so use frame timings
for consistency, too. These are:
- lvds panel,
- dvo encoders - dvo is the only way gen2 could support interlaced
mode, but currently we don't support any encoders that do.
- tv out - despite that the tv dac sends out an interlaced signal it
expects a progressive mode pipe configuration.
All these encoders enforce progressive modes by resetting
interlace_allowed.
Hence we always want crtc vertical timings in frames. Enforce this in
our crtc mode_fixup function and rip out any redudant timing
computations from the encoders' mode_fixup function.
v2-4: Adjust the vertical timings a bit.
v5: Split out the 'subtract-one for interlaced' fixes.
v6: Clarify issues around tv-out and gen2.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
There is an error in i915_read_blc_pwm_ctl, where the register values
are not being copied correctly. BLC_PWM_CTL and BLC_PWM_CTL2 are
getting mixed up. This patch fixes that so that saveBLC_PWM_CTL2 and
not saveBLC_PWM_CTL is copied to the BLC_PWM_CTL2 register.
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For i945 and earlier chips, the backlight frequency value had the low
bit (of 16) fixed to zero. The Pineview code path handled this by just
exposing the backlight range as 15 bits while other chips had the
backlight range limited to 0 .. 0xfffe.
This patch makes everyone take the pineview code path, providing 15
bits of backlight duty cycle range which seems more than sufficient to
me.
Daniel Mack reported that writing 1 to bit 0 of the duty cycle
register was causing problems on his Samsung X20 notebook, even when
the duty cycle value was less than the maximum backlight value. (He
tried a value of 29749 with max_brightness of 29750). This patch never
writes a '1' to that bit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org
|
|
When the brightness property is inquired while the backlight is disabled,
the driver returns a wrong value (zero) because it probes the value after
the backlight was turned off. This caused a black screen even after the
backlight is enabled again. It should return the internal backlight_level
instead, so that it won't be influenced by the backlight-enable state.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=41926
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/872652
Tested-by: Kamal Mostafa <kamal@canonical.com>
Cc: Alex Davis <alex14641@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The commit 47356eb67285014527a5ab87543ba1fae3d1e10a introduced a
mechanism to record the backlight level only at disabling time, but it
also introduced a regression. Since intel_lvds_enable() may be called
without disabling (e.g. intel_lvds_commit() calls it unconditionally),
the backlight gets back to the last recorded value. For example, this
happens when you dim the backlight, close the lid and open the lid,
then the backlight suddenly goes to the brightest.
This patch fixes the bug by recording the backlight level always
when changed via intel_panel_set_backlight(). And,
intel_panel_{enable|disable}_backlight() call the internal function not
to update the recorded level wrongly.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
backlight intensity on i915, so add native driver support.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Tested-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Consider a 1600x900 panel, upscaling a 1360x768 mode, full-aspect. The
old math would give you:
scaled_width = 1600 * 768; /* 1228800 */
scaled_height = 1360 * 900; /* 1224000 */
if (scaled_width > scaled_height) { /* pillarbox, and true */
width = 1224000 / 768; /* int(1593.75) = 1593 */
x = (1600 - 1593 + 1) / 2; /* 4 */
y = 0;
height = 768;
} /* ... */
This is broken. The total width of scanout would then be 1593 + 4 + 4,
or 1601, which is wider than the panel itself. The hardware very
dutifully implements this, and you end up with a black 45° diagonal from
the top-left corner to the bottom edge of the screen. It's a cool
effect and all, but not what you wanted. Similar things happen for the
letterbox case.
The problem is that you have an integer number of pixels, which means
it's usually impossible to upscale equally on both axes. 1360/768 is
1.7708, 1600/900 is 1.7777. Since we're constrained on the one axis,
the other one wants to come out as an even number of pixels (the panel
is almost certainly even on both axes, and the x/y offsets will be
applied on both sides). In the math above, if 'width' comes out even,
rounding down is correct; if it's odd, you'd rather round up. So just
increment width/height in those cases.
Tested on a Lenovo T500 (Ironlake).
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Daniel Manrique <daniel.manrique@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38851
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This commit changed an internal radeon structure, that meant a new driver
in -next had to be fixed up, merge in the commit and fix up the driver.
Also fixes a trivial nouveau merge.
Conflicts:
drivers/gpu/drm/nouveau/nouveau_mem.c
|
|
At least on my HP 2540p this is wrong at bootup, fine
at any other time once a lid event has occured. This is due to
_REG vs _INI ordering in the ACPI tables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit 951f3512dba5bd44cda3e5ee22b4b522e4bb09fb
drm/i915: Do not handle backlight combination mode specially
since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.
In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34524
Acked-by: Indan Zupancic <indan@nul.nu>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge in the conflicting eDP fix.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Seems like we are forever to be cursed with buggy firmware, so allow the
user to explicitly set the panel connection status.
Of secondary utility for cases where I run laptops with the lid closed,
but still want to configure the LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
The current code does not follow Intel documentation: It misses some things
and does other, undocumented things. This causes wrong backlight values in
certain conditions. Instead of adding tricky code handling badly documented
and rare corner cases, don't handle combination mode specially at all. This
way PCI_LBPC is never touched and weird things shouldn't happen.
If combination mode is enabled, then the only downside is that changing the
brightness has a greater granularity (the LBPC value), but LBPC is at most
254 and the maximum is in the thousands, so this is no real functional loss.
A potential problem with not handling combined mode is that a brightness of
max * PCI_LBPC is not bright enough. However, this is very unlikely because
from the documentation LBPC seems to act as a scaling factor and doesn't look
like it's supposed to be changed after boot. The value at boot should always
result in a bright enough screen.
IMPORTANT: However, although usually the above is true, it may not be when
people ran an older (2.6.37) kernel which messed up the LBPC register, and
they are unlucky enough to have a BIOS that saves and restores the LBPC value.
Then a good kernel may seem to not work: Max brightness isn't bright enough.
If this happens people should boot back into the old kernel, set brightness
to the maximum, and then reboot. After that everything should be fine.
For more information see the below links. This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=23472
http://bugzilla.kernel.org/show_bug.cgi?id=25072
Signed-off-by: Indan Zupancic <indan@nul.nu>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Share the lid detection code for the all panels for consistent behaviour
and a single place to add the eventual quirks for crap hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
... and not if the maximum is non-zero. This fixes the typo introduced
in 47356eb6728501452 and preserves the backlight value from boot.
[ickle: My thanks also to Indan Zupancic for diagnosing the original
regression and suggesting the appropriate fix.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org # after 47356eb6728501452
|
|
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
After a GPU reset, the backlight controller registers may be also reset
to 0. In that case we should restore those to the original values
programmed by the BIOS. Note that we still lack the code to handle the
case where the BIOS failed to program those registers at all...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Avoid confusion between i965g meaning broadwater and the gen4+ chipset
families.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.
Fixes:
Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
https://bugs.freedesktop.org/show_bug.cgi?id=29716
And a bug on one of my PineView boxes which overflowed the backlight
value.
Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
v2: Hook in DP paths to keep FULLSCREEN panel fitting on eDP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
