| Age | Commit message (Collapse) | Author |
|---|
|
In order to transition output drivers to using the struct tegra_output
as a helper rather than midlayer, make this callback optional. Instead
drivers should implement the equivalent as part of ->mode_fixup(). For
the conversion to atomic modesetting a new callback ->atomic_check()
should be implemented that updates the display controller's state with
the corresponding parent clock, rate and shift clock divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The output layer was initially designed to help reduce the amount of
code duplicated in output drivers. An unfortunate side-effect of that
was that it turned into a midlayer and it became difficult to make the
output drivers work without bending over backwards to fit into the
midlayer.
This commit starts to convert the midlayer into a helper library by
exporting most of the common functions so that they can be used by the
output drivers directly. Doing so will allow output drivers to reuse
common code paths but more easily override them where necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DRM core should take care of disabling all unneeded planes, so there
is no need to do this explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This structure will be extended using non-framebuffer related callbacks
in subsequent patches, so it should move to a more central location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When disabling the display controller, stop it and wait for it to become
idle. Doing so ensures that no further accesses to the framebuffer occur
and the buffers can be safely unmapped or freed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Previously output drivers would all stop the display controller in their
disable path. However with the transition to atomic modesetting the
display controller needs to be kept running until all planes have been
disabled so that software can properly determine (using VBLANK counts)
when it is safe to remove the framebuffers associated with the planes.
Moving this code into the display controller's disable path also gets
rid of the duplication of this into all output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All output drivers have open-coded variants of this function, so export
it to remove some code duplication.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This callback can be used instead of the legacy ->mode_fixup() and is
passed the CRTC and connector states. It can thus use these states to
validate the modeset and cache values in the state to be used during
the actual modeset.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to prevent drivers from having to perform the same checks over
and over again, add an optional ->atomic_disable callback which the core
calls under the right circumstances.
v2: pass old state and detect edges to avoid calling ->atomic_disable on
already disabled planes, remove redundant comment (Daniel Vetter)
v3: rename helper to drm_atomic_plane_disabling() to clarify that it is
checking for transitions, move helper to drm_atomic_helper.h, clarify
check for !old_state and its relation to transitional helpers
Here's an extract from some discussion rationalizing the behaviour (for
a full version, see the reference below):
> > Hm, thinking about this some more this will result in a slight difference
> > in behaviour, at least when drivers just use the helper ->reset functions
> > but don't disable everything:
> > - With transitional helpers we assume we know nothing and call
> > ->atomic_disable.
> > - With atomic old_state->crtc == NULL in the same situation right after
> > boot-up, but we asssume the plane is really off and _dont_ call
> > ->atomic_disable.
> >
> > Should we instead check for (old_state && old_state->crtc) and state that
> > drivers need to make sure they don't have stuff hanging around?
>
> I don't think we can check for old_state because otherwise this will
> always return false, whereas we really want it to force-disable planes
> that could be on (lacking any more accurate information). For
> transitional helpers anyway.
>
> For the atomic helpers, old_state will never be NULL, but I'd assume
> that the driver would reconstruct the current state in ->reset().
By the way, the reason for why old_state can be NULL with transitional
helpers is the ordering of the steps in the atomic transition. Currently
the Tegra patches do this (based on your blog post and the Exynos proto-
type):
1) atomic conversion, phase 1:
- implement ->atomic_{check,update,disable}()
- use drm_plane_helper_{update,disable}()
2) atomic conversion, phase 2:
- call drm_mode_config_reset() from ->load()
- implement ->reset()
That's only a partial list of what's done in these steps, but that's the
only relevant pieces for why old_state is NULL.
What happens is that without ->reset() implemented there won't be any
initial state, hence plane->state (the old_state here) will be NULL the
first time atomic state is applied.
We could of course reorder the sequence such that drivers are required
to hook up ->reset() before they can (or at the same as they) hook up
the transitional helpers. We could add an appropriate WARN_ON to this
helper to make that more obvious.
However, that will not solve the problem because it only gets rid of the
special case. We still don't know whether old_state->crtc == NULL is the
current state or just the initial default.
So no matter which way we do this, I don't see a way to get away without
requiring specific semantics from drivers. They would be that:
- drivers recreate the correct state in ->reset() so that
old_state->crtc != NULL if the plane is really enabled
or
- drivers have to ensure that the real state in fact mirrors the
initial default as encoded in the state (plane disabled)
References: http://lists.freedesktop.org/archives/dri-devel/2015-January/075578.html
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
There is no use-case where it would be useful for drivers not to
implement this function and the transitional plane helpers already
require drivers to provide an implementation.
v2: add new requirement to kerneldoc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
kfree(ERR_PTR(-ENOMEM)) will not work very well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
We can't save two values to the IRQ flags at the same time so the IRQs
are not enabled at the end. This kind of bug is easy to miss in testing
if the function is normally called with IRQs disabled so we wouldn't
enable IRQs anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Compliance testing shows that HS Trail is off by -12%. Increase the HS
Trail time to make this test pass.
Signed-off-by: David Ung <davidu@nvidia.com>
[treding@nvidia.com: update specification references, add comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This allows a DRM driver unload/reload cycle to completely reset the DSI
controller and may help in situations where it's broken.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This reset is necessary to properly clean up the internal state of the
controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DSI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use a sized unsigned 32-bit data type (u32) to store register contents.
The HDMI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This prevents the compiler from warning about using a variable that is
possibly uninitialized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Most of the display controller's registers are double-buffered, a few of
them are triple-buffered. The ASSEMBLY shadow copy is latched intto the
ACTIVE copy for double-buffered registers. For triple-buffered registers
the ASSEMBLY copy is first latched into the ARM copy.
Latching into the ACTIVE copy happens immediately if the controller is
inactive. Otherwise the latching happens on the next frame boundary. The
latching of the ASSEMBLY into the ARM copy happens immediately. Latching
is controlled by a set of *_ACT_REQ and *_UPDATE bits in the
DC_CMD_STATE_CONTROL register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra114 and earlier support specifying the color of the border (i.e.
the active area of the screen that is not covered by any of the overlay
windows). By default this is set to a light blue, so set it to black to
comply with the requirements set by atomic modesetting.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
iommu_domain_alloc() returns NULL on error, it never returns error
pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The possible_crtcs mask needs to be a mask of CRTC indices. There is no
guarantee that the DRM indices match the hardware pipe number, so the
mask must be computed from the CRTC index.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DRM core now zeroes out the memory associated with CRTC, encoder and
connector objects upon cleanup, so there's no need to explicitly do that
in drivers anymore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The iommu_map_sg() function is now available in the IOMMU API, so drop
the open-coded variant.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Previously the struct bus_type exported by the host1x infrastructure was
only a very basic skeleton. Turn that implementation into a more full-
fledged bus to support proper probe ordering and power management.
Note that the bus infrastructure needs to be available before any of the
drivers can be registered. This is automatically ensured if all drivers
are built as loadable modules (via symbol dependencies). If all drivers
are built-in there are no such guarantees and the link order determines
the initcall ordering. Adjust drivers/gpu/Makefile to make sure that the
host1x bus infrastructure is initialized prior to any of its users (only
drm/tegra currently).
v2: Fix building host1x and tegra-drm as modules
Reported-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The atomic helpers rely on drm_atomic_state_clear() to reset an atomic
state if a retry is needed due to the w/w mutexes. The subsequent calls
to drm_atomic_get_{crtc,plane,...}_state() would then return the stale
pointers in state->{crtc,plane,...}_states.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With the combination of ->enable and ->active it's a bit complicated
to follow what exactly is going on sometimes within a full modeset.
Add debug output to make this all traceable.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
For historical reasons going all the way back to how the Xrandr code
was implemented the semantics of the callbacks used to enable/disable
crtcs and encoders are ... interesting.
But with atomic helpers all that complexity has been binned, with only
a well-defined on/off action left. Unfortunately the names stuck.
Let's fix that by adding enable/disable hooks every, make them the
preferred variant for atomic and update documentations.
Later on we add debug warnings when drivers have deprecated hooks. But
while everything is in-flight with lots of drivers converting to
atomic that's a bit too much - better wait for things to settle a bit
first.
v2: Fix kerneldoc, reported by Wu Fengguang.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Cursor plane updates have historically been fully async and mutliple
updates batched together for the next vsync. And userspace relies upon
that. Since implementing a full queue of async atomic updates is a bit
of work lets just recover the cursor specific behaviour with a hint
flag and some hacks to drop the vblank wait.
v2: Fix kerneldoc, reported by Wu Fengguang.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This builds on top of the crtc->active infrastructure to implement
legacy DPMS. My choice of semantics is somewhat arbitrary, but the
entire pipe is enabled as along as one output is still enabled.
Of course it also clamps everything that's not ON to OFF.
v2: Fix spelling in one comment.
v3: Don't do an async commit (Thierry)
v4: Dan Carpenter noticed missing error case handling.
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This is the infrastructure for DPMS ported to the atomic world.
Fundamental changes compare to legacy DPMS are:
- No more per-connector dpms state, instead there's just one per each
display pipeline. So if you clone either you have to unclone first
if you only want to switch off one screen, or you just switch of
everything (like all desktops do). This massively reduces complexity
for cloning since now there's no more half-enabled cloned configs to
consider.
- Only on/off, dpms standby/suspend are as dead as real CRTs. Again
reduces complexity a lot.
Now especially for backwards compat the really important part for dpms
support is that dpms on always succeeds (except for hw death and
unplugged cables ofc). Which means everything that could fail (like
configuration checking, resources assignments and buffer management)
must be done irrespective from ->active. ->active is really only a
toggle to change the hardware state. More precisely:
- Drivers MUST NOT look at ->active in their ->atomic_check callbacks.
Changes to ->active MUST always suceed if nothing else changes.
- Drivers using the atomic helpers MUST NOT look at ->active anywhere,
period. The helpers will take care of calling the respective
enable/modeset/disable hooks as necessary. As before the helpers
will carefully keep track of the state and not call any hooks
unecessarily, so still no double-disables or enables like with crtc
helpers.
- ->mode_set hooks are only called when the mode or output
configuration changes, not for changes in ->active state.
- Drivers which reconstruct the state objects in their ->reset hooks
or through some other hw state readout infrastructure must ensure
that ->active reflects actual hw state.
This just implements the core bits and helper logic, a subsequent
patch will implement the helper code to implement legacy dpms with
this.
v2: Rebase on top of the drm ioctl work:
- Move crtc checks to the core check function.
- Also check for ->active_changed when deciding whether a modeset
might happen (for the ALLOW_MODESET mode).
- Expose the ->active state with an atomic prop.
v3: Review from Rob
- Spelling fix in comment.
- Extract needs_modeset helper to consolidate the ->mode_changed ||
->active_changed checks.
v4: Fixup fumble between crtc->state and crtc_state.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Not a new type exposed to userspace, just a standard way to create
them since between range, bitmask and enum there's 3 different ways to
pull out a boolean prop.
Also add the kerneldoc for the recently added new prop types, which
Rob forgot all about.
v2: Fixup kerneldoc, spotted by Rob.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
We don't have full atomic modeset support yet, but the "nuclear
pageflip" subset of functionality (i.e., plane operations only) should
be ready. Allow the user to force atomic on for debug purposes, or for
fixed-purpose embedded devices that will only use atomic for plane
updates.
The term 'nuclear' is used here instead of 'atomic' to make it clear
that this doesn't allow full atomic modeset support, just a (very
useful) subset of the atomic functionality.
We'll drop the kernel parameter and unconditionally enable atomic in a
future patch once all of the necessary pieces are in.
v2:
- Use module_param_named_unsafe() (Daniel)
- Simplify comment on DRIVER_ATOMIC guard (Daniel)
v3:
- Make the parameter "nuclear_pageflip" rather than just "nuclear"
for clarity. (Ander)
v4:
- Make the internal variable "nuclear_pageflip" as well as the
command-line option. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This will exercise our atomic pipeline for legacy property updates.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The atomic helpers need these to prepare a new state object when
starting a new atomic operation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.
For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core. Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.
v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We want to enable/test plane updates via the atomic interface, but as
soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic
codepaths to lookup properties during drmModeGetConnector() and some of
those codepaths unconditionally dereference connector->state
(specifically when looking up the CRTC ID property in
drm_atomic_connector_get_property()). Create a dummy connector state
for each connector at init time to ensure the DRM core doesn't try to
dereference a NULL connector->state. The actual connector properties
will never be updated or contain useful information, but since we're
doing this specifically for testing/debug of the plane operations (and
only when a specific kernel module option is given), that shouldn't
really matter.
Once we start creating connector states, the DRM core will want to be
able to clean them up for us. We also need to hook up the destruction
entrypoint to the core's helper.
v2: Squash in the patch to set the state destruction hook (Ander & Bob)
v3: Only create dummy connector states when we're actually faking
atomic support. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add the top-level atomic entrypoints for check/commit. These won't get
called yet; we still need to either enable the atomic ioctl or switch to
using the non-transitional atomic helpers for legacy operations.
v2:
- Use plane->pipe rather than plane->possible_crtcs while ensuring that
only a single CRTC is in use. Either way will work fine since i915
drm_plane's are always tied to a single CRTC, but plane->pipe is
slightly more intuitive. (Ander)
- Simplify crtc/connector checking logic. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When we flip on the DRIVER_ATOMIC bit, the DRM core will start calling
this entrypoint to set and lookup driver-specific plane property values,
rather than maintaining a shadow copy in object->properties.
Note that although we add these functions to the plane vtable, they will
not yet be called. Future patches that switch our .set_property()
handler and/or enable full atomic functionality are required before
these code paths will be executed.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
All of the previous refactoring/consolidation of plane code has resulted
in intel_primary_plane_funcs, intel_cursor_plane_funcs, and
intel_sprite_plane_funcs being identical. Replace all of these with a
single 'intel_plane_funcs' vtable for simplicity.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Runtime state that can be manipulated via properties should now go in
intel_plane_state/drm_plane_state so that it can be tracked as part of
an atomic transaction.
We add a new 'intel_create_plane_state' function so that the proper
initial value for this property (and future properties) doesn't have to
be repeated at each plane initialization site.
v2:
- Stick rotation in common drm_plane_state rather than
intel_plane_state. (Daniel)
- Add intel_create_plane_state() to consolidate the places where we
have to set initial state values. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Replace all the vlv_gpu_freq(), vlv_freq_opcode(),
*GT_FREQUENCY_MULTIPLIER, and /GT_FREQUENCY_MULTIPLIER instances
with intel_gpu_freq() and intel_freq_opcode() calls.
Most of the change was performed with the following semantic patch:
@@
expression E;
@@
(
- E * GT_FREQUENCY_MULTIPLIER
+ intel_gpu_freq(dev_priv, E)
|
- E *= GT_FREQUENCY_MULTIPLIER
+ E = intel_gpu_freq(dev_priv, E)
|
- E /= GT_FREQUENCY_MULTIPLIER
+ E = intel_freq_opcode(dev_priv, E)
|
- do_div(E, GT_FREQUENCY_MULTIPLIER)
+ E = intel_freq_opcode(dev_priv, E)
)
@@
expression E1, E2;
@@
(
- vlv_gpu_freq(E1, E2)
+ intel_gpu_freq(E1, E2)
|
- vlv_freq_opcode(E1, E2)
+ intel_freq_opcode(E1, E2)
)
@@
expression E1, E2, E3, E4;
@@
(
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_gpu_freq(E3, E4);
- } else {
- E2 = intel_gpu_freq(E3, E4);
- }
+ E2 = intel_gpu_freq(E3, E4);
|
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_freq_opcode(E3, E4);
- } else {
- E2 = intel_freq_opcode(E3, E4);
- }
+ E2 = intel_freq_opcode(E3, E4);
)
One hunk was manually undone as intel_gpu_freq() ended up
calling itself. Supposedly it would be possible to exclude
certain functions via !=~, but I couldn't get that to work.
Also the removal of vlv_gpu_freq() and vlv_opcode_freq() compat
wrappers was done manually.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Rename the vlv_gpu_freq() and vlv_freq_opecode() functions to have
an intel_ prefix, and handle non-VLV/CHV platforms in them as well.
Leave the vlv_ names around for now since they're currently used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently the 'gt_cur_freq_mhz' file shows the actual GPU frequency on
VLV/CHV, and the last requested frequency on other platforms. Change the
meaning of the file on VLV/CHV to follow the the other platforms, and
introduce a new file 'gt_act_freq_mhz' which shows the actual frequency
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently we don't call valleyview_set_rps() when changing the min/max
limits through sysfs if the current frequency is still within the new
limits. However that means we sometimes forget to update PMINTRMSK.
Eg. if the current frequency is at the old minimum, and then we reduce
the minum further we should then enable the 'down' interrupts in PMINTRMSK
but currently we don't.
Fix it up by always calling valleyview_set_rps() (just like we do for
!vlv/chv platforms). This also allows the code to be simplified a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Calls have been added to invalidate/flush DRRS whenever invalidate/flush is
called as part of frontbuffer tracking.
Apart from calls as a result of GEM tracking to fb invalidate/flush, a
call has been added to invalidate fb obj from crtc_page_flip as well. This
is to track busyness through flip calls.
The call to fb_obj_invalidate (in flip) is placed before queuing flip for this
obj.
drrs_invalidate() and drrs_flush() check for drrs.dp which would be NULL if
it was setup in drrs_enable(). This covers for the condition when DRRS is
not supported.
v2: Removing the call to invalidate_drrs from page_flip.
This has not been tested on Android yet, but, in case DRRS transtions do not
work as expected, check by adding back this call in page_flip.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Calling enable/disable DRRS when enable/disable DDI are called.
These functions are responsible for setup of drrs data (in enable) and
reset of drrs (in disable).
has_drrs is true when downclock_mode is found and SEAMLESS_DRRS is set in
the VBT. A check has been added for has_drrs in these functions, to make
sure the functions go through only if DRRS will work on the platform with
the attached panel.
V2: [By Ram]: WARN_ON is used when intel_edp_drrs_enable() is called more than
once [Rodrigo]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add DRRS work function to trigger a switch to low refresh rate,
when no activity is detected on screen till 1 sec duration.
v2: [By Ram]: drrs.dp also protected with drrs.mutex and worker function
is renamed to intel_edp_drrs_downclock_work [Chris]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Self-explanatory code is better code.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Const is good for you. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
