| Age | Commit message (Collapse) | Author |
|---|
|
Add a driver for the i2c-tiny-usb interface. This is a simple
do-it-yourself USB to I2C interface targeted at experimental and
home use. See the i2c-tiny-usb homepage for hardware details:
http://www.harbaum.org/till/i2c_tiny_usb
Signed-off-by: Till Harbaum <till@harbaum.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Platform driver for the Simtec CPLD based simple I2C logic.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This is a very simple bitbanging I2C bus driver utilizing the new
arch-neutral GPIO API. Useful for chips that don't have a built-in
I2C controller, additional I2C busses, or testing purposes.
To use, include something similar to the following in the
board-specific setup code:
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PIN_FOO,
.scl_pin = GPIO_PIN_BAR,
};
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
Register this platform_device, set up the I2C pins as GPIO if
required and you're ready to go. This will use default values for
udelay and timeout, and will work with GPIO hardware that does not
support open drain mode, but allows sensing of the SDA and SCL lines
even when they are being driven.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The i2c linux driver for blackfin architecture which supports blackfin
on-chip TWI controller i2c operation.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
New driver for the PA Semi SMBus interfaces.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the I2C bus found on the ARM Versatile and Realview
platforms. The I2C bus has a RTC and optionally some EEPROMs attached.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the I2C (Two-wire interface) controller integrated in
the Atmel AT91RM9200 processor. This driver should also be usable on
the Atmel AT91SAM9261 and AT91SAM9260 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
New I2C bus driver for Philips ARM boards (Philips IP3204 I2C IP
block). This I2C controller can be found on (at least) PNX010x,
PNX52xx and PNX4008 Philips boards.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The rest of the ITE8172 support was already removed from MIPS tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
|
|
i2c: New bus driver for TI OMAP boards
This patch adds I2C bus driver for various Texas
Instruments (TI) OMAP1/2 (http://www.ti.com/omap) series
based boards like OMAP1510/1610/1710/242x.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The following patch adds support for the OpenCores I2C controller IP
core (See http://www.opencores.org/projects.cgi/web/i2c/overview).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The SMU is the "system controller" chip used by Apple recent G5 machines
including the iMac G5. It drives things like fans, i2c busses, real time
clock, etc...
The current kernel contains a very crude driver that doesn't do much more
than reading the real time clock synchronously. This is a completely
rewritten driver that provides interrupt based command queuing, a userland
interface, and an i2c/smbus driver for accessing the devices hanging off
the SMU i2c busses like temperature sensors. This driver is a basic block
for upcoming work on thermal control for those machines, among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add support for the I2C PXA driver.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
