| Age | Commit message (Collapse) | Author |
|---|
|
As the driver and hardware always process the given data in parallel,
then it would be better to initialize tx_limit, rx_limit and rx_valid
variables just prior to being used.
This will help us to send / receive as much data as possible.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
While we have a local variable "buf_len" for dev->tx_buf_len, we don't
have such local variable for dev->tx_buf pointer. While "buf_len" is
restored at first then updated when we start processing a new i2c_msg
(determined by STATUS_WRITE_IN_PROGRESS flag), ->tx_buf is different.
Such inconsistency makes the code slightly hard to follow.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
We have some steps at the top of i2c_dw_xfer_msg() to set up a slave
address and enable DW I2C core. And it's executed only when we don't
have STATUS_WRITE_IN_PROGRESS.
But we need to make sure that STATUS_WRITE_IN_PROGRESS only indicates
that we have a pending i2c_msg to process. In other words, even if
STATUS_WRITE_IN_PROGRESS is not set, that doesn't mean we're at initial
state in the I2C transaction.
Since i2c_dw_xfer_msg() will be invoked again and again during a
transaction, those init steps have a possibility to be re-processed
needlessly. For example, this issue easily takes place when processing
a combined transaction with a certain condition (the number of tx bytes
in the first i2c_msg, equals to the Tx FIFO depth).
Consequently we should not use STATUS_WRITE_IN_PROGRESS to determine
where we're at in an I2C transaction. It would be better to separate
those initialization steps from i2c_dw_xfer_msg().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Enable RX_FULL interrupt mask by default, and hook it in the interrupt
handler. If requested amount of rx data (defined by IC_RX_TL) is not
available, we don't have to process i2c_dw_read().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.
In other words, we must never make "Tx FIFO underrun" happen during
a transaction, except for the last byte. For the safety's sake, we'd
make TX_EMPTY interrupt get triggered every time one byte is processed.
The Rx FIFO threshold needs to be set as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Symptom:
--------
When we're going to send/receive the longer size of data than the Tx
FIFO length, the I2C transaction will be divided into several separated
transactions, limited by the Tx FIFO length.
Details:
--------
As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.
Then, once a new transmit data is written to the Tx FIFO, DW I2C core
will initiate a new transaction, which leads to another START condition.
This explains how the transaction in question goes, and implies that
current tasklet-based dw_i2c_pump_msg() strategy couldn't meet the
timing constraint required for avoiding Tx FIFO underrun.
To avoid this scenario, we must keep providing new transmit data within
a given time period. In case of Fast-mode + 32-byte Tx FIFO, for
instance, it takes about 22.5[us] to process single byte, and 720[us] in
total.
This patch removes the existing tasklet-based "pump" system, and move
its jobs into the interrupt handler.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
In case a work-in-progress i2c_msg has more bytes to be written, we
need to set STATUS_WRITE_IN_PROGRESS and exit from the msg_write_idx-
searching loop. Otherwise, we will overtake the current msg_write_idx
without waiting for its transmission to be processed.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
* Calculate with accurate conditional expressions from DW manuals.
* Round ic_clk by adding 0.5 as it's important at high ic_clk rate.
* Take into account "tHD;STA" issue for _HCNT calculation.
* Take into account "tf" for _LCNT calculation.
* Add "cond" and "offset" fot further correction requirements.
For _HCNT calculation, there's one issue needs to be carefully
considered; DesignWare I2C core doesn't seem to have solid strategy
to meet the tHD;STA timing spec. If you configure _HCNT based on the
tHIGH timing spec, it easily results in violation of the tHD;STA spec.
After many trials, we came to the conclusion that the tHD;STA period
is proportional to (_HCNT + 3). For the safety's sake, this should be
selected by default.
As for _LCNT calculation, DW I2C core has one characteristic behavior;
he starts counting the SCL CNTs for the LOW period of the SCL clock
(tLOW) as soon as it pulls the SCL line. At that time, he doesn't take
into account the fall time of SCL signal (tf), IOW, he starts counting
CNTs without confirming the SCL input voltage has dropped to below VIL.
This characteristics becomes a problem on some platforms where tf is
considerably long, and results in violation of the tLOW timing spec.
To make the driver configurable as much as possible for various cases,
we'd have separated arguments "tf" and "offset", and for safety default
values should be 0.3 us and 0, respectively.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
We couldn't know the original intent for this variable, but at this
point it's useless.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
We're strongly discouraged from using the IC_CLR_INTR register because
it clears all software-clearable interrupts asserted at the moment.
stat = readl(IC_INTR_STAT);
:
: <=== Interrupts asserted during this period will be lost
:
readl(IC_CLR_INTR);
Instead, use the separately-prepared IC_CLR_* registers.
At the same time, this patch adds all remaining interrupt definitions
available in the DesignWare I2C hardware.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This driver looks originally meant for armel machines where readw()/
writew() works perfectly fine with this hardware. But that doens't
work for big-endian systems.
This patch converts all 8/16-bit-aware usages to 32-bit variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This is required to test some drivers, for example at24.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Functions i2c_do_add_adapter() and __attach_adapter() do essentially
the same thing, differing only in how the parameters are passed. Same
for i2c_do_add_adapter() and __detach_adapter(). Introduce wrappers to
normalize the parameters, so that we do not have to duplicate the
code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
|
|
The Intel 82801 is sometimes used on systems with a BMC connected. The
BMC can access the SMBus, resulting in lost arbitration for the 82801.
We should let i2c-core retry transactions for us in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The BKL is held over a kmalloc so cannot protect anything beyond that.
The two calls before the kmalloc have their own locking.
Improve device open function by removing the now unnecessary ret variable
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The kind parameter of i2c_detect_address() always has value -1, so we
can get rid of it.
Next step is to update all i2c detect callback functions to get rid of
this now useless parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)
The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.
This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
These _setup functions are called from _probe so they can be marked
__devinit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
I2C bus drivers don't have to support I2C_M_REV_DIR_ADDR. It is a
deviation from the I2C specification, which only makes sense to
implement when really needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
|
|
Low priority thread holding the i2c bus mutex could block higher
priority threads to access the bus resulting in unacceptable
latencies. Change the mutex type to rt_mutex preventing priority
inversion.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@nokia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
|
|
We no longer need to write the adapter name to a temporary buffer.
We can write it directly to the i2c_adapter's name field. This is
more efficient.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Include the i2c_adapter in struct pmac_i2c_bus. This avoids memory
fragmentation and allows for several code cleanups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Log errors when they happen, otherwise we have no idea what went
wrong.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
|
|
I wanted to add some error logging to the i2c-powermac driver, but
found that it was very difficult due to the way the
i2c_powermac_smbus_xfer function is organized. Refactor the code in
this function so that each low-level function is only called once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
|
|
The i2c-powermac driver doesn't support arbitrary multi-message I2C
transactions, only SMBus ones. Make it clear by returning an error if
a multi-message I2C transaction is attempted. This is better than only
processing the first message, because most callers won't recover from
the short transaction. Anyone wishing to issue multi-message
transactions should use the SMBus API instead of the raw I2C API.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
|
|
As i2c/chips is deprecated, move ds1682 to a more apropriate location.
Build tested.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
at24: Use timeout also for read
i2c: Fix userspace_device list corruption
MAINTAINERS: Add missing i2c files
i2c/tsl2550: Fix lux value in extended mode
|
|
Fix userspace_device list corruption. The corruption was caused by
clients not being removed when adapters with such clients were
themselves removed. Something like the following would trigger it
(assuming i2c-stub gets adapter number 3):
# modprobe i2c-stub chip_addr=0x50
# echo 24c08 0x50 > /sys/bus/i2c/devices/i2c-3/new_device
# rmmod i2c-stub
# modprobe i2c-stub chip_addr=0x50
# echo 24c08 0x50 > /sys/bus/i2c/devices/i2c-3/new_device
For the records, the stack trace in the kernel logs look like this:
kernel: WARNING: at lib/list_debug.c:30 __list_add+0x8b/0x90()
kernel: Hardware name: (...)
kernel: list_add corruption. prev->next should be next (c137fc84), but was (null). (prev=f57111b8).
kernel: Modules linked in: (...)
kernel: Pid: 4669, comm: bash Not tainted 2.6.32-rc8 #259
kernel: Call Trace:
kernel: [<c111eb8b>] ? __list_add+0x8b/0x90
kernel: [<c111eb8b>] ? __list_add+0x8b/0x90
kernel: [<c103265c>] warn_slowpath_common+0x6c/0xc0
kernel: [<c111eb8b>] ? __list_add+0x8b/0x90
kernel: [<c10326f6>] warn_slowpath_fmt+0x26/0x30
kernel: [<c111eb8b>] __list_add+0x8b/0x90
kernel: [<c11ba165>] i2c_sysfs_new_device+0x1c5/0x250
kernel: [<c10861be>] ? might_fault+0x2e/0x80
kernel: [<c11b9fa0>] ? i2c_sysfs_new_device+0x0/0x250
kernel: [<c118c625>] dev_attr_store+0x25/0x30
kernel: [<c10e305c>] sysfs_write_file+0x9c/0xf0
kernel: [<c109d35c>] vfs_write+0x9c/0x160
kernel: [<c10e2fc0>] ? sysfs_write_file+0x0/0xf0
kernel: [<c109d4dd>] sys_write+0x3d/0x70
kernel: [<c1002ed8>] sysenter_do_call+0x12/0x36
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
According to the TAOS Application Note 'Controlling a Backlight with
the TSL2550 Ambient Light Sensor' (page 14), the actual lux value in
extended mode should be obtained multiplying the calculated lux value
by 5.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This allows i2c-pnx to free its interrupt handler when the module
is removed or if an error occurs; using the same dev_id for both
request_irq and free_irq is desirable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
|
|
Added missing mach/i2c.h and linux/io.h header file includes
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Limit minimum jiffie timeout to 2 to prevent early timeout on systems
with low tick rates
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Change SB900 to its formal code name Hudson-2.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).
This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Enable clock before START, disable it after STOP.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
check cpu_is_mx1() when disable delay.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.
If we don't check busy bit, START/STOP may fail on some fast CPUs.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
We recently removed the acpi_device_uid() interface because nobody
used it. I don't think it's essential here either.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Conflicts:
MAINTAINERS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Clearly mark ACPI drivers as such
i2c: Add driver for SMBus Control Method Interface
i2c-pnx: Correct use of request_region/request_mem_region
MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
i2c-piix4: Add AMD SB900 SMBus device ID
i2c/chips: Remove deprecated pcf8574 driver
i2c/chips: Remove deprecated pca9539 driver
i2c/chips: Remove deprecated pcf8575 driver
gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
i2c/scx200_acb: Provide more information on bus errors
i2c: Provide compatibility links for i2c adapters
i2c: Convert i2c adapters to bus devices
i2c: Convert i2c clients to a device type
i2c/tsl2550: Use combined SMBus transactions
i2c-taos-evm: Switch echo off to improve performance
i2c: Drop unused i2c_driver.id field
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
As I2C is used by PMICs also, make the busses available early via
subsys_initcall().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The mv64xxx_i2c_intr() irq handler in drivers/i2c/busses/i2c-mv64xxx.c
is declared as returning 'int', resulting in this compile-time warning:
drivers/i2c/busses/i2c-mv64xxx.c: In function 'mv64xxx_i2c_probe':
drivers/i2c/busses/i2c-mv64xxx.c:540: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Fix: correct the return type to 'irqreturn_t'.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
