| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: log scsi_target ID at release
ieee1394: fix NULL pointer dereference in sysfs access
|
|
Regression since "ieee1394: prevent device binding of raw1394,
video1394, dv1394", commit d2ace29fa44589da51fedc06a67b3f05301f3bfd:
$ cat /sys/bus/ieee1394/drivers/raw1394/device_ids
triggers a NULL pointer dereference in fw_show_drv_device_ids.
Reported by Miles Lane.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Miles Lane <miles.lane@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: silence defined but not used warning in non-modular builds
ieee1394: rawiso: requeue packet for transmission after skipped cycle
|
|
Currently the kernel will issue the following warning:
drivers/ieee1394/raw1394.c:2938: warning: 'raw1394_id_table' defined but not used
Add #ifdef MODULE guards around the declaration.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Ditto with dv1394_id_table and video1394_id_table.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
As it seems, some host controllers have issues that can cause them to
skip cycles now and then when using large packets. I suspect that this
is due to DMA not succeeding in time. If the transmit fifo can't contain
more than one packet (big packets), the DMA should provide a new packet
each cycle (125us). I am under the impression that my current PCI
express test system can't guarantee this.
In any case, the patch tries to provide a workaround as follows:
The DMA program descriptors are modified such that when an error occurs,
the DMA engine retries the descriptor the next cycle instead of
stalling. This way no data is lost. The side effect of this is that
packets are sent with one cycle delay. This however might not be that
much of a problem for certain protocols (e.g. AM824). If they use
padding packets for e.g. rate matching they can drop one of those to
resync the streams.
The amount of skips between two userspace wakeups is counted. This
number is then propagated to userspace through the upper 16 bits of the
'dropped' parameter. This allows unmodified userspace applications due
to the following:
1) libraw simply passes this dropped parameter to the user application
2) the meaning of the dropped parameter is: if it's nonzero, something
bad has happened. The actual value of the parameter at this moment does
not have a specific meaning.
A libraw client can then retrieve the number of skipped cycles and
account for them if needed.
Signed-off-by: Pieter Palmers <pieterp@joow.be>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
The following patch limits the node speed to the host interface speed,
before using it.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
It should actually suffice to do this only for the local node's
speedcap[]. But there is another bug in the speed calculation:
The local node's speed is not correctly propagated to the speeds
which are to be used to access remote nodes.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/11772/focus=12024
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Unless you're adding a kobject to the sysfs hierarchy, there is no
point setting its kobject name.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The failure path of ohci1394_pci_probe() reuses ohci1394_pci_remove().
Doing so it missed to call ohci1394_pmac_off() in a few unlikely early
error cases.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
to reduce the size of ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
We don't want to hide something like return in a preprocessor macro.
Unroll the macro and use a goto, which also reduces the size of
ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Clean up shared code and variable names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.
Add the necessary feature call to .resume. Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
These drivers don't need to match any unit_directory type device.
They just need the id_table for module autoloading per module alias.
Not binding any of these drivers allows special-purpose drivers with
similar or same IDs to bind to devices. This currently only benefits
out-of-tree drivers; on the other hand it is in no way detrimental to
in-tree drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
replace all:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
expression_in_cpu_byteorder);
with:
beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
generated with semantic patch
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Fix I/O errors due to SYM13FW500's inability to handle larger request
sizes. Reported by Piergiorgio Sartor <piergiorgio.sartor@nexgo.de> for
firewire-sbp2 in https://bugzilla.redhat.com/show_bug.cgi?id=436879
This fix is necessary because sbp2's default request size limit has been
lifted since 2.6.25-rc1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
rescan-scsi-bus used to add SBP-2 targets which weren't there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Add the same workaround as found in fw-sbp2 for feature parity and
compatibility of the workarounds module parameter.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
sg_dma_len(sg) is invalid before the s/g list is DMA-mapped.
This fixes a post 2.6.24 regression which prevents access to SBP-2
devices on several architectures, introduced by "ieee1394: sbp2: s/g
list access cosmetics", commit 825f1df545ab0289185373b0eaf06fb0b3487422.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Bug noted by Pieter Palmers: Isochronous transmit tasklets were
scheduled on isochronous receive events, in addition to the proper
isochronous receive tasklets.
http://marc.info/?l=linux1394-devel&m=119783196222802
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This patch speeds up sbp2 a little bit --- but more importantly, it
brings the behavior of sbp2 and fw-sbp2 closer to each other. Like
fw-sbp2, sbp2 now does not limit the size of single transfers to 255
sectors anymore, unless told so by a blacklist flag or by module load
parameters.
Only very old bridge chips have been known to need the 255 sectors
limit, and we have got one such chip in our hardwired blacklist. There
certainly is a danger that more bridges need that limit; but I prefer to
have this issue present in both fw-sbp2 and sbp2 rather than just one of
them.
An OXUF922 with 400GB 7200RPM disk on an S400 controller is sped up by
this patch from 22.9 to 23.5 MB/s according to hdparm. The same effect
could be achieved before by setting a higher max_sectors module
parameter. On buses which use 1394b beta mode, sbp2 and fw-sbp2 will
now achieve virtually the same bandwidth. Fw-sbp2 only remains faster
on 1394a buses due to fw-core's gap count optimization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The code has been in "#if 0 - #endif" since Linux 2.6.12.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Convert ieee1394 from nopage to fault.
Remove redundant vma range checks (correct resource range check is retained).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Replace sg->length by sg_dma_len(sg). Rename a variable for shorter
line lengths and eliminate some superfluous local variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
Convert to use the class iteration api.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Torsten Kaiser wrote:
> Looking that calltrace upwards, it seems replacing the
> memset(dma->sglist,...) with sg_init_table(...) would fix the BUG_ON()
> as that inits the SG_MAGIC.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch removes dead code spotted by the Intel C Compiler.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Commits
58b053e4ce9d2fc3023645c1b96e537c72aa8d9a ("Update arch/ to use sg helpers")
45711f1af6eff1a6d010703b4862e0d2b9afd056 ("[SG] Update drivers to use sg helpers")
fa05f1286be25a8ce915c5dd492aea61126b3f33 ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
drivers/ieee1394/ieee1394_core.c: Define spinlock using
DEFINE_SPINLOCK instead of assignment to SPIN_LOCK_UNLOCKED
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
At least since nodemgr got rid of coarse global locking, accesses to
struct csr1212_keyval's reference counter should be atomic and coupled
with proper barriers. Also, calls to csr1212_keep_keyval(kv) should
occur before kv is being used.
(We probably should convert refcnt to struct kref, but how to keep
csr1212_destroy_keyval's implementation non-recursively then?)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
csr1212_keep_keyval(kv) in nodemgr_process_root_directory was
unbalanced if ne->vendor_name_kv already exists. This happens for
example if eth1394 or raw1394 modify the local config ROM and it is
parsed again.
As a bonus, the attempt to add the vendor_name_kv sysfs attribute
when it already exists is now fixed for good.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
* Delete optional and empty i2c client_register and client_unregister
callbacks.
* Use the proper i2c adapter ID.
* Don't use a template to initialize the i2c_adapter structure, it's
inefficient.
* Update a misleading comment on why we use i2c_transfer rather than
higher level i2c functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The nodemgr host thread can exit on its own even when kthread_should_stop
is not true, on receiving a signal (might never happen in practice, as
it ignores signals). But considering kthread_stop() must not be mixed with
kthreads that can exit on their own, I think changing the code like this
is clearer. This change means the thread can cut its sleep short when
receive a signal but looking at the code around, that sounds okay (and
again, it might never actually recieve a signal in practice).
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
sbp2_host_reset and sbp2_handle_status_write are not serialized against
sbp2_alloc_device and sbp2_remove_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
bad_proto can be reached from points which did not take priv->lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
