| Age | Commit message (Collapse) | Author |
|---|
|
On the at91_adc a minimal Sample and Hold Time is necessary for the ADC to
guarantee the best converted final value between two channels selection.
This time has to be programmed through the bitfield SHTIM in the
Mode Register ADC_MR.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The sleep mode will allow to put the adc in sleep between conversion.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
at91 adc offers the choice between two resolutions: low and high.
The low and high resolution values depends on adc IP version, as many IP
properties have been exposed through device tree, these settings have also
been added to the dt bindings.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
exynos_adc is a DT only driver and exynos_adc_match table is always
compiled in. Hence remove the macro.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Introduce iio_tigger_{set,get}_drvdata which allows to attach driver specific
data to a trigger. The functions wrap access to the triggers private_data field
and all current users are updated to use iio_tigger_{set,get}_drvdata instead of
directly accessing the private_data field. This is the first step towards
removing the private_data field from the iio_trigger struct.
The following coccinelle script has been used to update the drivers:
<smpl>
@@
struct iio_trigger *trigger;
expression priv;
@@
-trigger->private_data = priv
+iio_trigger_set_drv_data(trigger, priv)
@@
struct iio_trigger *trigger;
@@
-trigger->private_data
+iio_trigger_get_drv_data(trigger)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Without this change the exynos adc controller needed to have its phy
enabled in some out-of-driver C code. Add support for specifying the
phy enable register by listing it in the reg list.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The ad7924 is software compatible with the ad7923. The ad7904 and ad7914 are the
8 and 10 bit version of the ad7924.
While we are at it also drop the "with temperature sensor" from the Kconfig
entry, since the chips do not have a temperature sensor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver already claims to support scale reporting in its channel spec, but
doesn't actually implement this yet. This patch uses the regulator API to get
the reference voltage and calculates the scale based on that. The patch also
moves the global configuration bits into a field in the ad7923_state struct,
since depending on the RANGE bit, the range goes either from 0 to VREF or from 0
to 2 * VREF. So we need to know the setting of the RANGE bit when calculating
the scale.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Instead of leaving 'val' uninitialized return an error if the result's address
did not match that of the channel we were trying to read.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
As the exynos_adc driver only supports device tree registration.
Making driver depend on CONFIG_OF solves possible errors during probe.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
cc: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
cc: Lars Poeschel <poeschel@lemonage.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
cc: Patil, Rachna <rachna@ti.com>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
cc: Milo(Woogyom) Kim <milo.kim@ti.com>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds New driver to support:
1. Supports ADC IF found on EXYNOS4412/EXYNOS5250
and future SoCs from Samsung
2. Add ADC driver under iio/adc framework
3. Also adds the Documentation for device tree bindings
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for Analog Devices AD7923 ADC in the IIO Subsystem.
Signed-off-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg Kroah-Hartman:
"Here's the big staging tree merge for 3.9-rc1
Lots of cleanups and updates for drivers all through the staging tree.
We are pretty much "code neutral" here, adding just about as many
lines as we removed.
All of these have been in linux-next for a while."
* tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (804 commits)
staging: comedi: vmk80xx: wait for URBs to complete
staging: comedi: drivers: addi-data: hwdrv_apci3200.c: Add a missing semicolon
staging: et131x: Update TODO list
staging: et131x: Remove assignment of skb->dev
staging: wlan-ng: hfa384x.h: fix for error reported by smatch
staging/zache checkpatch ERROR: spaces prohibited around that
staging/ozwpan: Mark read only parameters and structs as const
staging/ozwpan: Remove empty and unused function oz_cdev_heartbeat
staging/ozwpan: Mark local functions as static (fix sparse warnings)
staging/ozwpan: Add missing header includes
staging/usbip: Mark local functions as static (fix sparse warnings)
staging/xgifb: Remove duplicated code in loops.
staging/xgifb: Consolidate return paths
staging/xgifb: Remove code without effect
staging/xgifb: Remove unnecessary casts
staging/xgifb: Consolidate if/else if with identical code branches
staging: vt6656: replaced custom TRUE definition with true
staging: vt6656: replaced custom FALSE definition with false
staging: vt6656: replace custom BOOL definition with bool
staging/rtl8187se: Mark functions as static to silence sparse
...
|
|
Implement external reference voltage as regulator named "vref".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
"Third set of IIO new drivers, cleanups and fixes for the 3.9 cycle
New drivers
1) A driver for ST microelectronics sensors. This driver already covers
a large set of new parts (20 gyros, accelerometer and magnetometers)
not currently covered by the existing drivers. The intent moving forward
is to merge this with the other drivers for similar parts already in tree.
The lis3l02dq driver currently in staging/iio will be trivial, the lis3
driver in misc more complex as it has a number of additional interfaces.
Any merging in of the lis3 driver will rely on the not currently
merged iio_input bridge driver and handling of freefall notifications
etc.
2) A driver for the itg3200 gyroscope.
Graduations from staging
1) Cleanup and move out of staging of the adxrs450 gyroscope driver. The
cleanup required was all minor but there were a couple of fixes hidden in
there.
Core and driver additions
1) Initial work from Guenter Roeck on device tree support for IIO's provider/
consumer code. Focuses on the iio_hwmon driver and the max1363 adc driver.
The full device tree syntax is currently under discussion but should
follow shortly.
Cleanups and fixes
1) Remove a noop function __iio_update_buffer
2) Couple of small fixes and cleanups for the max1363
"
|
|
merge commit 17cb3be61b45d716f6b21a9380925493413ce0ed
seems to have resulted in two functions that were removed in
4389fbec5b8fd0577c1e854ff5d7139329558c20 reappearing.
Spotted due to a build kicking out
drivers/iio/adc/max1363.c:1486:12: warning: 'max1363_register_buffered_funcs_and_init' defined but not used
drivers/iio/adc/max1363.c:1521:13: warning: 'max1363_buffer_cleanup' defined but not used
This patch just removes them again.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of requiring the map to unregister, simply unregister all map entries
associated with the given iio device. This simplifies map removal and also works
for maps generated through devicetree.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
For chips with more than 8 bit ADC resolution, received data was always
masked against 0xfff, ie with a 12 bit mask. This can result in bad data
for chips with 10 bit resolution if those chips have higher bits set
(seen with MAX1139).
The receive buffer was defined as char array. This could result in
unintentional sign extensions if the upper bit in a received byte
was set. Since the chip is configured for unipolar mode, we never
have to handle negative values, and sign extensions are never needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
ERROR: "iio_triggered_buffer_setup" [drivers/iio/adc/max1363.ko] undefined!
ERROR: "iio_triggered_buffer_cleanup" [drivers/iio/adc/max1363.ko] undefined!
add select IIO_TRIGGERED_BUFFER
IIO_TRIGGERED_BUFFER in turn selects IIO_TRIGGER and IIO_KFIFO_BUF, so drop those
MAX1363_RING_BUFFER is not used anymore
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This resolves a merge issue with a iio driver, and the zram code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg Kroah-Hartman:
"Here are a number of small fixes to staging drivers for your 3.8-rc3
tree.
Well, the omapdrm fixes aren't really "small" but they were waiting on
a number of other drm patches to go in through the drm tree, and got
delayed by my vacation over the holidays. They are totally
self-contained, everyone involved have acked them, and they fix issues
that people have been having with the driver.
Other than that one, it's a bunch of tiny bugfixes for a number of
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (36 commits)
staging: zram: fix invalid memory references during disk write
staging: tidspbridge: use prepare/unprepare on dsp clocks
staging: tidspbridge: Fix build breakage due to splitting CM functions.
staging: comedi: comedi_test: fix race when cancelling command
staging: comedi: Kconfig: COMEDI_NI_AT_A2150 should select COMEDI_FC
staging: comedi: prevent auto-unconfig of manually configured devices
staging: comedi: fix minimum AO period for NI 625x and NI 628x
staging: vme_pio2: fix oops on module unloading
staging: speakup: avoid out-of-range access in synth_add()
staging: speakup: avoid out-of-range access in synth_init()
staging: rtl8192e: Fix failure to check pci_map_single()
staging: rtl8187se: Fix failure to check pci_map_single()
staging: drm/imx: fix double free bug in error path
staging: drm/imx: several bug fixes
staging: drm/imx: check return value of ipu_reset()
staging: drm/omap: fix flags in dma buf exporting
staging: drm/omap: use omapdss low level API
staging/fwserial: Update TODO file per reviewer comments
staging/fwserial: Limit tx/rx to 1394-2008 spec maximum
staging/fwserial: Refine Kconfig help text
...
|
|
This is to get the comedi fixes, and resolve the issue in comdi_test.c
and comedi_fops.c that were caused by changes in both branches.
It also allows the fwserial driver changes to be applied, as they
required the fixes that are in staging-linus.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use 'dev' of iio device in a kernel message rather than i2c client device node.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The lp8788-adc is a platform driver of lp8788-mfd.
The platform device is allocated when mfd_add_devices() is called
in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device of
iio device and device kernel message.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
use iio_triggered_buffer_setup(), iio_triggered_buffer_cleanup()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Instantiating the driver with no available regulator results in:
[39711.686393] i2c i2c-7: new_device: Instantiated device max1139 at 0x35
[39711.688687] BUG: unable to handle kernel paging request at fffffffffffffe13
[39711.688734] IP: [<ffffffff813e835b>] regulator_disable+0x1b/0x80
[39711.688788] PGD 1c0e067 PUD 1c0f067 PMD 0
[39711.688835] Oops: 0000 [#1] SMP
Caused by bad probe error path. Fix it.
Driver should also not attempt to free the interrupt in its error path if
none was allocated. Fix that problem as well.
Finally, testing if the regulator was allocated is not necessary in the
remove function, since the probe function bails out if this is the case.
Remove that check.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
regulator_get_voltage() may return negative error code.
Add error checking to avoid setting error code to st->vref_uv.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
/opt/work/linux-2.6/drivers/iio/adc/at91_adc.c: In function 'at91_adc_trigger_handler':
/opt/work/linux-2.6/drivers/iio/adc/at91_adc.c:83:22: error: 'indio_dev' undeclared (first use in this function)
/opt/work/linux-2.6/drivers/iio/adc/at91_adc.c:83:22: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
|
|
Add support for reading conversion results from the ADC and provide them
through a single IIO channel. A proper scaling factor is also exported
based on the reference voltage provided by a regulator.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The ad7796 and ad7797 are similar to the ad7792 and ad7793 but only have a
single differential input instead of two. Also some other features are missing
like the programmable gain amplifier and also not all sampling frequencies
supported by the ad7792/ad7793 are supported by the ad7796/ad7797. This patch
adds new feature flags for the features not present in the ad7796/ad7797. The
patch also adds a struct iio_info field to the chip_info struct, this becomes
necessary since the ad7796/ad7797 needs a special set of sysfs attributes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
